Pentair Side Pool Cleaner User manual

LEGEND® PLATINUM INSTALLATION MANUAL
LEGEND
®
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Installation Guide
Pressure Side Pool Cleaner

LEGEND® PLATINUM INSTALLATION MANUAL
© 2005 Pentair Water Pool and Spa, Inc. All rights reserved.
This document is subject to change without notice.
1620 Hawkins Ave., Sanford, NC 27330 • [phone]
10951 West Los Angeles Ave., Moorpark, CA 93021 • [phone]
Trademarks and Disclaimers. The Pentair Water Pool and Spa logo is a trademark of Pentair Water Pool and Spa, Inc. The Legend Platinum logo
is a registered trademark of Pentair Water Pool and Spa, Inc. Other trademarks and trade names may be used in this document to refer to either
the entities claiming the marks and names or their products. Pentair Water Pool and Spa, Inc. disclaims any proprietary interest in trademarks and
trade names other than its own.
Customer Service
If you have questions about ordering Pentair replacement parts, and pool products,
please use the following contact information:
Customer Service (8 A.M. to 5 P.M. — Eastern and Pacific Times)
Phone: [phone]
Fax: [phone]
Technical Support
Sanford, North Carolina (8 A.M. to 5 P.M. — Eastern Time)
Phone: [phone]
Fax: [phone]
Moorpark, California (8 A.M. to 5 P.M. — Pacific Time)
Phone: [phone] (Ext. 5591)
Fax: [phone]
Web site
visit www.pentairpool.com and www.staritepool.com to find information about our products

LEGEND® PLATINUM INSTALLATION MANUAL
Important Information:
The Legend®Platinum automatic pool cleaner comes ready to connect into a female threaded 1-1/2"
line, dedicated to our Universal Booster Pump. Also, if you have a chlorinator, solar system or other air
inducing equipment, contact our Technical Support Department at 1-800-831-7133 before you install the
Legend®Platinum. (See diagram on page 2).
The following are important facts to remember before installing and operating the Legend®Platinum.
1. Always disconnect the Legend®Platinum from the pool wall when cleaning or back washing the pool
filter.
2. After cleaning or back washing, let the filtration system run for at least five minutes before reconnecting
the Legend®Platinum.
3. New plumbing lines should be flushed out before installing the Legend®Platinum.
4. The Legend®Platinum should not be used to remove plaster dust in new pools.
5. Always remove the Legend®Platinum before swimmers enter the pool.
6. Always handle the Legend®Platinum with care. Do not let children or pets play with the unit:
it is not a toy.
7. Always pick up the Legend®Platinum by the Vacuum Tube especially when lifting the unit out of the
water.
8. Unless checking the wheel RPM, do not handle the Legend®Platinum while it is operating.
9. Always remove the Legend®Platinum from the pool before chemical shock treatments. As a rule, any
pool water that is unsafe for swimming is unsafe for the Legend®Platinum.
10. Carefully cut the feed hose following the instructions on Page 3.
By following these simple guidelines, you can help protect against injury and prolong the life of
your Legend®Platinum.
Before the Legend®Platinum is installed, please take a moment to record the serial number. This number
is located on your warranty card and on the back of the Legend®Platinum near the rear jets. You will be
asked for this number when you contact our Technical Support Department.
SERIAL #__________________________________
LL105PM / LL105PMG
LL105PMTGG / LL105PMTWW
LL105PMTRW / LL105PMTYW
LEGEND
®

LEGEND® PLATINUM INSTALLATION MANUAL
TABLE OF CONTENTS
I. Introduction ................................................................................................................................1
A. Thank You for Choosing the Legend®Platinum. ................................................................. 1
B. What to Expect from the Legend®Platinum. ..................................................................... 1
II. Installation Instructions .............................................................................................................. 2
A. Legend®Platinum Components ........................................................................................ 2
B. Pool Connections ............................................................................................................. 2
C. Booster Pump Installation ................................................................................................ 2
D. Installing the Twist Lock Pressure Relief Valve (Wall Fitting) ............................................ 3
E. Cutting the Feed Hose ................................................................................................... 3-6
F. Checking Operation ......................................................................................................... 7
G. Fine Tuning the Legend®Platinum..................................................................................... 7
1. Thrust Jet Adjustment ................................................................................................. 7
2. Sweep Hose Adjustment ............................................................................................. 7
3. Checking Wheel RPM ................................................................................................. 8
III. Operation & Periodic Maintenance ............................................................................................. 9
A. Connecting/Disconnecting the Legend®Platinum ............................................................. 9
B. Turning the Legend®Platinum On/Off ............................................................................... 9
C. Cleaning the Sand & Silt Bag ........................................................................................... 9
D. Periodic Maintenance ....................................................................................................... 9
1. Wall Fitting Screen ...................................................................................................... 9
2. Tires & Bearings ....................................................................................................... 10
3. Roller Rings .............................................................................................................. 10
4. Debris Bags .............................................................................................................. 10
5. Sweep Hose .............................................................................................................. 10
6. Debris Valve .............................................................................................................. 10
E. Back Washing the Pool Filter .......................................................................................... 10
F. Storage and Winterizing ................................................................................................. 10
G. Accessories ...................................................................................................................10
1. Sweep Hose Weight .................................................................................................. 10
2. Leaf Bag ................................................................................................................... 10
IV. Troubleshooting ................................................................................................................... 11-12
Legend®Platinum Parts List ........................................................................................... 13-14
Legend®Platinum Exploded View ........................................................................................ 15

LEGEND® PLATINUM INSTALLATION MANUAL
I. Introduction
A. Thank You for Choosing the
Legend®Platinum Pool Cleaner
Congratulations on the purchase of your new
automatic pool cleaner. The Legend®Platinum is
designed to give you years of dependable and
efficient service. With the Legend®Platinum, you and
your family will spend more time relaxing and
enjoying your pool and less time cleaning it.
The Legend®Platinum has been designed and built
with time proven features and patented innovations
to create an automatic pool cleaner that will give you
years of dependable service. The Legend®Platinum
is built with pride in the U.S.A., by people who care
about the product using state of the art materials and
backed by a limited warranty that protects against
defects in parts and construction.
Like any mechanical device, the Legend®Platinum
requires some preventative maintenance and the
replacement of certain working parts. We
recommend that you have your Legend®Platinum
checked annually. For best results have your
Legend®Platinum installed by a qualified swimming
pool professional.
For pool owners with plumbing and mechanical
experience, installation instructions are included in
this manual.
Please put safety first! Be sure to take your
Legend®Platinum out of your pool and store it
carefully in a shaded area before anyone enters the
pool.
B. What to Expect from the Legend®
Platinum
When operating correctly, the Legend®Platinum will
travel randomly throughout the pool, vacuuming and
sweeping the bottom. The climbing ability of the
Legend®Platinum is dependent on the pool’s shape.
It will climb better in pools without sharp angles or
curves in the transition from the pool floor to the pool
wall.
The Legend®Platinum comes equipped with a
Wall Fitting (Part # EW22-White, Part # LLW22PM-
Gray) that features a Twist Lock Automatic
Pressure Relief Valve. If the Legend®Platinum is
receiving too much water pressure to the unit, the
relief valve will automatically reduce water pressure.
Approximately every three minutes and 30 seconds,
the Legend®Platinum will go into a back up mode.
At this time, the Back Up Valve will pull the Legend®
Platinum away from problem areas.
The Sweep Hose operates in a gentle sweeping
motion to prevent debris from becoming trapped in
hard to reach corners of the pool.
1

LEGEND® PLATINUM INSTALLATION MANUAL
II. Installation Instructions
A. Legend®Platinum Components
The Legend®Platinum Box Contains:
1. Cleaner Head
2. Sand & Silt Bag
3. Sweep Hose
4. Complete Feed Hose
a. 1 - 8½ in. hose
b. 2 - 10 ft. long hoses
c. 1 - 30 in. soft hose/1 - 7½ ft. soft hose
d. 10 - Floats
e. 3 - Swivels
f. 1- Back-Up Valve
g. 10 - Mender Nuts
h. 1 - Wall Fitting complete
B. Pool Connections
The Legend®Platinum comes equipped to connect
to a female threaded 1-1/2 in. line, dedicated to our
Universal Booster Pump.
Also, if the pool doesn't have a dedicated cleaner
line please contact our Technical Support
Department at 1-800-831-7133.
C. Booster Pump Installation
If you already have a 3/4 horsepower booster pump
installed at your equipment pad and it is operational,
skip this section and proceed to Installing the Twist
Lock Pressure Relief Valve (Wall Fitting).
Detailed booster pump installation instructions are
packaged separately in our booster pump box.
Please follow these instructions carefully.
The booster pump is not self-priming and needs to
be fed with water taken from the pool filter before
any type of in-line chlorinator. See figure below.
2

LEGEND® PLATINUM INSTALLATION MANUAL
D. Installing the Twist Lock Pressure
Relief Valve (Wall Fitting)
1. Take out any existing pool cleaner and/or wall
fitting.
2. Turn on the filtration pump and booster pump,
flush out the plumbing line.
3. Turn off filter pump and booster pump.
4. Remove the Wall Adapter from the Wall Fitting
and screw Adapter by hand into the dedicated
line. Turn until tight.
WALL ADAPTER
INSTALLED
QUICK
LOCK
PEG
QUICK DISCONNECT
O-RING
5. Take the Wall Fitting and Twist Lock the Wall Fitting
into the Wall Adapter 1/4 turn and pull out, to a
snug fit. Once the Wall Adapter is secure, you
can now twist lock and unlock to remove Wall
Fitting with ease from the Wall Adapter.
3
E. Cutting the Feed Hose
The Hose assembly comes in 5 sections now
covering approximately 30 ft. of the pool, which
provides ample hose for most residential pools. The
Back-Up Valve is now 30 in. from the head cleaner
and should always remain this distance. For larger
pools see #14 on page 6 for instructions on Adding
Additional Feeder Hose.
1. Take Feeder Hose out of box (it will be
approximately 30 feet long). Before installing
the unit, you should lay the feed hose out straight
in the sun, (for one day if possible). The hose has
been curled up in the box and sometimes will go
around in a circle. If this happens, take the first or
second section of hose from the wall and reverse
it, (turn it around). You might have to reverse both
sections to correct the problem. Make sure the
feed hose is cut and installed properly.
2. Measure how deep your pool is by using your
telepole or the clear end of the feeder hose.
Cut the clear (soft) hose equal to the depth of your
pool. (Hint: the grate or domed main drain at
the bottom is usually the deepest point.)
Example: The clear (soft) hose is 10 ft. long, if the
pool is 8½ ft. deep, cut 1½ ft. off of the clear (soft)
hose. If the depth is greater than 10 ft., do not cut
the clear (soft) hose.
Deepest End of Pool
Telepole / Clear (Soft) Hose
Measure and Mark the Water Level
Main Drain

LEGEND® PLATINUM INSTALLATION MANUAL
4
7½ FT.
EXAMPLE DIMENSION
(Your Measurement May Differ)
NOT TO SCALE
MARKED SWIVEL
FARTHEST POINT OF POOL PERIMETER
FROM WALL FITTING
STEPS
1. With the feed hose assembly attached to the pool wall, hold the feed hose assembly
by the opposite end with the clear hose and walk the perimeter of the pool to locate
the farthest point on the perimeter from the wall fitting without stretching the hose assembly.
2. Measure the distance that the hose assembly extends beyond the pool perimeter
farthest point located in Step 1 — (7½ ft. in this example).
3. Cut half of the length obtained from Step 2 — (3¾ ft. in this example),
equally from each of the 10 foot lengths of white or grey hose on either
side of the marked swivel.
10 FOOT
WHITE OR GREY
HOSE SECTION
10 FOOT
WHITE OR GREY
HOSE SECTION
10 FOOT
SOFT HOSE
BACK UP
VALVE
REMOVE EXCESS MATERIAL
FROM HOSE ON EITHER SIDE OF
MARKED SWIVEL AS DESCRIBED
IN STEPS 2 AND 3.
WALL FITTING
SWIVEL
SWIVEL
FLOATS
FLOATS
FLOATS
EXAMPLE OF HOSE ASSEMBLY
BEFORE CUTTING TO LENGTH
EXAMPLE OF FINISHED HOSE ASSEMBLY
AFTER CUTTING TO LENGTH
WHITE OR GREY
HARD HOSE SECTION
MARKED SWIVEL
END OF
SOFT HOSE
(End remains 30 in.)
SOFT HOSE
(Cut to your pool depth)
BACK UP VALVE FURTHEST POINT
OF POOL PERIMETER
FROM WALL FITTING
STEPS
4. Reassemble the hoses using the supplied mender nuts
as shown in
FIGURE 1 .
5. Your complete finished hose assembly should look like this.
The end of the 30 inch clear hose should reach just to the
furthest edge of the pool perimeter as shown.
WHITE OR GREY
HARD HOSE SECTION
FIGURE 1
WHITE OR GREY
HARD HOSE SECTION
(WALL FITTING SIDE)
WHITE OR GREY
HARD HOSE SECTION
(CLEANER SIDE)
MARKED SWIVEL

LEGEND® PLATINUM INSTALLATION MANUAL
5
7. Re-assemble the hoses and the swivel using
mender nuts (see Figure below, Step 1). Put
mender nut on swivels first, then push hose over
swivel (see Figure below, Step 2). Rotate mender
nut over hose clockwise until tight. Note: Keep
as many floats as possible on the long feed
hoses, spaced evenly apart to hold hose up
on top of water.
FEED
HOSE
MENDER
NUT
BARB ON SWIVEL
OR LEGEND
STEP 1
STEP 2
STEP 3
PUSH HOSE OVER BARB
PUSH MENDER NUT TOWARD HOSE AND ROTATE
CLOCKWISE BY HAND UNTIL TIGHT
SMALL END
OF MENDER
NUT AWAY
FROM HOSE
E. Cutting the Feed Hose - (cont.)
3. Lay the telepole next to the clear (soft) hose. If
the clear (soft) hose is longer than the mark on
the telepole, cut the excess from the end attached
to the white (hard) hose. Do not cut off the float.
Leave the first float in position next to the
Back-Up Valve. Place the second float midway
between the first float and the Hose Swivel.
4. Attach feed hose to the wall fitting and attach to
the pool wall. Hold the end of the 30 in. clear (soft)
hose and walk the perimeter of the pool keeping
the hose straight (do not stretch hose) to find the
farthest point of the pool from the wall fitting.
5. Measure the excess length between the farthest
point of the pool from Wall Fitting and the end of
30 in. clear (soft) hose.
6. Half of this measured length to be cut equally
from the 10 ft. long hoses next to the Marked
Swivel. (Example: Half of 6 ft. = 3 ft. each). If you
are cutting more than 2 ft. off the hoses, remove
the floats next to the Marked Swivel from both
hoses. See Figures on page 4.
Water Level
White (Hard) Hoses Swivel
Cut and Remove the
Excess Hose Length Cut Clear (Soft) Hose Equal to
the Deepest Pool Water Level
Telepole / Clear (Soft) Hose

LEGEND® PLATINUM INSTALLATION MANUAL
E. Cutting the Feed Hose - (cont.)
8. When cutting hoses, please use strong scissors
or a sharp knife. Be sure to slide the floats out of
the way when cutting hose.
9. Put extra mender nut on the Legend®Platinum
mast and push soft hose gently over mast at
1/2 in., turn mender nut around soft hose tight.
Note: The Back-Up Valve still should be 30 in.
from the head of the cleaner.
FEED HOSE
MENDER NUT
FEED MAST
SWIVEL
10. Now take the bag, EU16, out of the box and firmly
twist lock the bag onto the top of the Legend®
Platinum throat over rubber debris valve.
11.Review and check list: Hoses cut properly and
floats evenly spaced. Mender nuts tight around
swivels, back up valve, Legend®Platinum mast
and wall fitting. Make sure wall fitting is securely
locked into place.
12.Lower your complete Legend®Platinum
assembly into your pool carefully. It should look
like figure below.
13.Go back to your equipment and turn filter pump
on first (wait 30 seconds to force air out of the
hose), then turn booster pump on.
14.For large pools requiring more hose length you
will need to purchase one (1) additional hose
(LLD45-White or LLD45PM-Gray), four (4) floats
(ED10P-White or LLD10PM-Gray), one (1) swivel
(ED05-White or LLD05PM-Gray), and two (2)
mender nuts (ED15-White or LLD16PM-Gray).
Attach extra hose between long hoses using
floats, swivel and mender nuts. Divide extra hose
overage by three (3) this time to keep all hoses
the same length.
FIRST
SWIVEL
SECOND
SWIVEL THIRD
SWIVEL
SHORT
WHITE
HOSE
LONG
WHITE
HOSE
LONG
WHITE
HOSE BACK UP
VALVE
CLEAR
HOSE
6

LEGEND® PLATINUM INSTALLATION MANUAL
F. Checking Operation
When operating correctly, the Legend®Platinum will
travel in a random pattern throughout the pool,
vacuuming and sweeping the bottom. The climbing
ability of the Legend®Platinum is dependent on the
pools structure and water flow coming into the pool.
It will perform more efficiently in pools without sharp
angles or curves in the transition from the floor of the
pool to the wall.
The Legend®Platinum comes with a Twist Lock
Pressure Relief Valve (Wall Fitting). If the Legend®
Platinum is receiving too much water pressure, the
Relief Valve in the Wall Fitting will release the excess
water pressure.
Approximately every three minutes and 30 seconds
the Legend®Platinum will go into a back-up mode.
The Back-Up Valve cycle time, while in the back-up
mode, is approximately 30 seconds, pulling the
Legend®Platinum from problem areas.
New Back-Up Valve Information:
The Back-Up Valve Insert (#MBUVP) which is slid
into the slot over the jet of the valve. This is secured
with a stainless steel screw (#VX-9) as show in the
diagram. The insert will be set from the factory with
the smaller (1/4") hole over the opening of the jet.
The smaller hole is used for the Platinum cleaner. If
you change the insert to the larger (3/8") hole, the
Back-Up Valve will have decreased jet pressure and
possible not pull the unit backwards.
If the Legend®Platinum does not travel to all areas
of the pool, turn off the booster pump and pool
filtration pump and make the necessary adjustments
from the instructions in the next section.
G. Fine Tuning the Legend®Platinum
1. Thrust Jet Adjustment
There are Thrust Jets located in the back of the
Legend®Platinum. These Thrust Jets alter the
direction of the cleaner. The factory standard position
for the jets are: Left jet set slightly to the right and
Right jet straight out.
(See illustration below.)
Screw
MBUVP
Back-Up Valve
2. Sweep Hose Adjustment
The Sweep Hose operates in a gentle sweeping
motion to prevent debris from becoming trapped in
hard to reach corners of the pools. To increase or
decrease the motion of the Sweep Hose, there is an
adjustment screw located on the Feed Mast Barb
below the Ballast Float. Turning the screw clockwise
will decrease the motion and counter clockwise to
increase the motion of the Sweep Hose.
Patents Pending
LEFT RIGHT
7

LEGEND® PLATINUM INSTALLATION MANUAL
3. Checking Wheel RPM
To determine whether the Legend®Platinum is
receiving the proper water pressure, turn off the
booster pump, pool pump and carefully remove the
Legend®Platinum from the pool.
Mark the front drive Tire/Wheel with a marker, or use
the Logo located on the side of tire as a marker to
count the rotations of the wheel per minute.
Have someone turn on pool pump and then booster
pump while you place the Legend®Platinum in
the pool just beneath the water surface. (Be sure to
hold onto the Sweep Hose to avoid getting wet).
Count the rotations of the marked wheel for exactly
one minute. (Be sure the Back-Up Valve isn't cycling
at this time). The rotations will give you the
Revolutions Per Minute, (RPM).
For proper performance, the Legend®Platinum
operates between 28-32 RPM. If the RPM is below
28 then call your local Pool Professional or contact
our Technical Support Department at 1-800-831-7133.
If the RPM is more than 32, at the Wall Fitting
unscrew the Pressure Valve slowly until the RPM
falls between 28-32.
If you have any additional questions, please
contact our Technical Support Department @
1-800-831-7133.
8

LEGEND® PLATINUM INSTALLATION MANUAL
III. Operation/Periodic Maintenance
A. Connecting/Disconnecting the
Legend®Platinum
Turn off booster pump and pool pump. Then take the
Wall Fitting and twist lock the Wall Fitting clockwise
into the Wall Adapter. To disconnect the Legend®
Platinum, unlock and twist counter clockwise. The
Wall Adapter should remain in the pool wall.
B. Turning On/Off the Legend®Platinum
The Legend®Platinum operates off the booster pump
coming from the equipment pad, and can be turned
on or off by merely turning on/off your booster pump
time clock.
C. Cleaning the Sand & Silt Bag
Carefully unlock the debris bag from the vacuum tube
and open the Velcro®Brand Fastener closure at the
top of debris bag and dump debris.
If you have a lot of debris in your pool, especially
after a storm, you can run your Legend®Platinum in
two shorter cycles per day and empty the debris bag
between cycles.
Reconnect the debris bag to the vacuum tube.
Do NOT over turn.
If the Velcro®Brand Fastener strip on top of the debris
bag does not stay secure, rinse well, let it dry and
clean with a stiff brush.
A Helpful Hint: It is easier to empty the debris bag
when it is dry. A second bag may be used while the
full debris bag is drying.
It's best to empty the debris bag when it becomes
half full. The Legend®Platinum will have better
performance if the bag is not overloaded.
D. Periodic Maintenance
The following parts are wear items that should be
checked, maintained or replaced as needed. Wear
items are considered any working or moving part(s)
being worn due to the use of the cleaner. Wear items
are not covered under warranty.
1. Wall Fitting Screen
Inside the wall fitting is a filter screen that acts as a
secondary filter. This screen is to keep debris that is
passed by the pool filter out of the Legend®Platinum.
Running the Cleaner without the filter screen can
damage the Legend®Platinum and will void the
warranty.
A continuous plugged or dirty screen is a sign of
problems in your pool filtration system and you need
to contact your local pool professional.
To clean the filter screen, pull the screen out from
inside the Wall Fitting and rinse thoroughly and push
back inside the wall fitting.
Whenever cleaning, back washing or repairing the
filter, remove the wall fitting and flush out the
dedicated line before using the Legend®Platinum.
9

LEGEND® PLATINUM INSTALLATION MANUAL
III. Operation/Periodic Maintenance -
(cont.)
2. Tires & Bearings
The tires are designed to protect the bottom of your
pool and provide better traction. You need to rotate
or replace the tires when edges become rounded.
The Wheel Bearings are warranted free of defects
when shipped from Pentair Water Pool and Spa, Inc.,
and are considered a wear item. A good bearing will
spin freely.
3. Roller Rings
Your Sweep Hose has a series of Roller Rings to
protect the Sweep Hose. Replace the rings as
needed. You can rotate the Roller Rings to prevent
flat spots.
4. Debris Bags
Fine Mesh Sand & Silt Bag
The Legend®Platinum comes with a Sand & Silt bag
for general use in all pools. We do not recommend
using the fine mesh bag to pick up leaves and twigs
or other large debris for they have sharp points and
edges that can poke holes and eventually rip the bag.
Optional Leaf Bag
The leaf bag is a larger mesh bag made to pick up
heavier debris such as leaves, twigs, acorns, etc.
This bag can be helpful especially after a storm.
A Helpful Hint: To prolong the life of bags, remove
cleaner from pool before adding chemicals.
5. Sweep Hose
The Sweep Hose is provided to help keep the bottom
and sides of your pool clean. The Sweep Hose is
warranted free of defects when shipped from the
factory, and is considered a wear item.
6. Debris Valve
This valve is located under the Debris Bag, it is
designed to keep the debris inside the bag. It
functions like a check valve to allow the debris to
only enter through the bag one way. Replacement is
needed when valve begins to stiffen.
E. Back Washing the Pool Filter
Always disconnect the Legend®Platinum from the
pool wall before cleaning or back washing the pool
filter. After cleaning or back washing, let the pool
filtration system run for a minimum of five minutes to
flush out the return lines before reconnecting the
Legend®Platinum.
F. Storage and Winterizing
Never leave or store the Legend®Platinum in direct
sunlight. When storing the Legend®Platinum for the
winter, be sure to drain all the water from it. This is
important since freeze damage is not covered under
the warranty. Also, remove the Wall Fitting.
G. Accessories
1. Sweep Hose Weight
If the sweep hose tends to break the surface of the
water therefore squirting nearby windows or innocent
bystanders, a weight can be installed to the end of
the sweep hose.
(Part # for Hose Weight is EH09C)
2. Leaf Bag (See Debris Bags #4)
10

LEGEND® PLATINUM INSTALLATION MANUAL
To insure the best performance from your cleaner,
follow the troubleshooting guide listed below.
IV. TROUBLESHOOTING AND PERFORMANCE TIPS
Problem: Legend®Platinum will not back up.
Solution: 1. Determine if the Back-Up Valve is
cycling. (Hold the valve out of the
water and the jet should come on for
approx. 30 seconds, and shut off for
approx. 3 minutes and 30 seconds).
2. Check the wheel RPM (See page 8).
3. Empty the debris bag if full or half full.
Problem: Legend®Platinum will not climb.
Solution: 1. Even if your pool doesn't show algae
you still need to brush the sides of the
pool wall.
2. Check the wheel RPM (See page 8).
3. Reposition the Thrust Jet. Loosen the
four screws to adjust the Thrust Jet.
A reminder: The climbing ability of the Legend®
Platinum is dependent on the pool's shape and
available water pressure. It will climb better in pools
without sharp angles or curves in the transition
from the pool floor to the pool wall.
Problem: Hoses tangling.
Solution: 1. Check the length of the Feed Hose,
they may be to long. (See pages 3-6 ).
2. Check to see that the Feed Hose is
floating on top of surface. Check hose
floats for even spacing.
3. Twist the Hose Swivels to see if they
spin freely and replace any that will not.
4. Lay out the Feed Hose straight in the
full sun to remove any memory.
A. PROBLEMS & SOLUTIONS
Problem: Legend®Platinum doesn't move or
moves sluggishly or hangs up on steps.
Solution: 1. Be sure filter pump and booster pump
are on and working properly. (You may
need to clean your pool filter system).
2. Check the Wall Fitting screen for debris
and rinse clean.
3. Check wheel RPM (See page 8).
4. Determine if the Back-Up Valve is
cycling. (Hold the valve out of the
water and the jet should come on for
approx. 30 seconds and shut off for
approx. 3 minutes and 30 seconds.)
5. Check all the Hose connections and
Swivels for leaks that can cause loss
of water pressure.
6. Check debris that may be jammed in
the gear teeth on one of the front drive
wheels. Gently rotate the front wheels
backward to dislodge debris.
Problem: Legend®Platinum falling over or lying on
it's side.
Solution: 1. This usually indicates the bag needs
to be emptied.
2. Check to see if the ballast float
(EA20-White or LLA20G-Gray) is
leaking by checking if there is water
inside. Unscrew by pull back while
turning counter-clockwise. When it
comes off, shake it and listen for water
in float.
11

LEGEND® PLATINUM INSTALLATION MANUAL
IV. TROUBLESHOOTING AND PERFORMANCE TIPS
A. PROBLEMS & SOLUTIONS - (cont.)
Problem: Sweep Hose is sucked into the cleaner.
Solution: 1. Adjust the Sweep Hose using the
Adjustment Screw located on the
bottom of the Swivel Mast. Turn
Adjustment Screw clockwise until the
Sweep Hose is in a gentle sweeping
motion.
Problem: Booster Pump very noisy.
Solution: 1. Make sure Wall Fitting is mounted in
pool wall correctly.
2. Make sure Pool Filtration system is
working properly.
3. Contact your local Pool Professional -
possible Booster Pump problem.
Problem: Sweep Hose breaks surface and sprays
nearby windows, patio decks and
bystanders.
Solution: 1. Adjust Sweep Hose to a gentle
sweeping motion.
2. Add optional Sweep Hose weight
(See page 10).
12

LEGEND® PLATINUM INSTALLATION MANUAL
LEGEND®PLATINUM PARTS LIST
Part #
LLU5PM
LLU145N
LLU145NG
EU10N
LLU10NG
LLU6
LLU6G
EC86
EC83
EC80
EA40
LLA40G
EC110
LLC110PM
EX120
LLX120
EC120
LLC120G
EB5L
LLB5G
EB10
EB25
LLB25PM
EB20
LLB20G
EA20
LLA20PMG
EH07
LLH07PM
EU15
EU15G
EU16
EU16G
EU9
EU7
E18
EC130
LLC130G
EC135
LLC135G
EC65
EC70
EC45
LLC6PM
LLC6PMG
Diagram #
1
2
2
3
3
4
4
5
6
7
8
8
9
9
10
10
11
11
12
12
13
14
14
15
15
16
16
17
17
18
18
19
19
20
21
22
23
23
24
24
25
26
27
28
28
Description
Top Cover - Gray
Main Frame - White
Main Frame - Gray
Bottom Cover - White
Bottom Cover - Gray
Feed Mast w/O-Ring - White
Feed Mast w/O-Ring - Gray
Turbine Drive Shaft - Complete
Turbine Spacers
Turbine Bearings - Gray
Turbine Shaft Shield - White
Turbine Shaft Shield - Gray
Turbine Cover w/Elbow - White
Turbine Cover w/Elbow - Gray
Turbine Cover Hose - 9" length - White
Turbine Cover Hose - 9" length - Gray
Venturi Jet - Hose - 7 3/4" length - White
Venturi Jet - Hose - 7 3/4" length - Gray
Sweep Hose - Complete - White
Sweep Hose - Complete - Gray
Sweep Hose - Wear Ring
Sweep Hose - Jet w/Collar - White
Sweep Hose - Jet w/Collar - Gray
Sweep Hose - Adjustment Screw - White
Sweep Hose - Adjustment Screw - Gray
Ballast Float - White
Ballast Float - Gray
Sweep Hose - Hose Sleeve - White
Sweep Hose - Hose Sleeve - Gray
Coarse Mesh Bag - White Collar
Coarse Mesh Bag - Gray Collar
Fine Mesh Bag - White Collar
Fine Mesh Bag - Gray Collar
Debris Valve
O-Ring for Feed Mast
O-Ring for Thrust Jet
Thrust Jets - White
Thrust Jets - Gray
Thrust Jet Plates - White
Thrust Jet Plates - Gray
Axle - Large Wheels
Axle Plate
Axle - Lock Washer
Wheel w/out Bearings - White
Wheel w/out Bearings - Gray
Quantity
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
9
1
1
1
1
1
1
17
17
1
1
1
1
1
1
2
2
2
2
2
4
4
8
4
4
4
13

LEGEND® PLATINUM INSTALLATION MANUAL
LEGEND®PLATINUM PARTS LIST
Part #
LLC60PM
E10
LL10PM
EC55
LLC55PM
LLC1PM
LLC1PMG
EB15
EC40
LLD50
LLD50PM
ED10P
LLD10PM
LLD45
LLD45PM
ED05
LLD05PM
LLU1
LLU1PM
ED15
LLD15PM
LLW22PM
EW22
LL25PM
E25
E24
LL23PM
E23
EC64
EG15
EC131
LLC131G
EU30
EU76
EU147
LLU147G
EU79
EU80
LLU8G
EU80
LLU81PM
LLU81PMG
Diagram #
29
30
30
31
31
32
32
33
34
35
35
36
36
37
37
38
38
39
39
40
40
41
41
41
41
42
43
43
44
45
46
46
47
48
49
49
50
51
51
52
53
53
Description
Wheel Bearings Only - Gray
Back-Up Valve - White
Back-Up Valve - Gray
Wheel Screw - Plastic - White
Wheel Screw - Plastic - Gray
Wheel - Rubber Tire - White
Wheel - Rubber Tire - Gray
Hose Clamp
Screw
Feed Hose - clear soft - 10'
Feed Hose - Gray soft - 10'
Float - Feed Hose - White
Float - Feed Hose - Gray
Feed Hose - 10' - White
Feed Hose - 10' - Gray
Swivel - Feed Hose - White
Swivel - Feed Hose - Gray
Adapter Hose - 8-1/2" - White
Adapter Hose - 8-1/2" - Gray
Mender Nut - plastic - White
Mender Nut - plastic - Gray
Wall Fitting - Gray
Wall Fitting - White
Pressure Relief Valve - Gray
Pressure Relief Valve - White
Screen - Wall Fitting
Quick Disconnect Adapter - Gray
Quick Disconnect Adapter - White
Wheel - Plastic Washer
Gears - for Back-Up Valve
Thrust Jet Repair Kit includes: (White)
E18, EC130, EC135
Thrust Jet Repair Kit includes: (Gray)
E18, LLC130G, LLC135G
Screw for EA40 or LLA40G
and EC110 or LLC110PM
Axle Bolt
Snap Fit Vac Tube Posts - White
Snap Fit Vac Tube Posts - Gray
Nut & Bolt - Feed Mast to Vac Tube
Venturi Jet - White
Venturi Jet - Gray
Screw - Cover to Frame
Front Bumper - White
Front Bumper - Gray
Quantity
8
1
1
4
4
4
4
5
8
1
1
10
10
2
2
2
2
1
1
8
8
1
1
1
1
1
1
1
4
1
1
1
5
8
2
2
1
2
2
2
1
1
14

LEGEND® PLATINUM INSTALLATION MANUAL
LEGEND®PLATINUM EXPLODED VIEW
15
8.5" FIRST 10'
HOSE SECOND 10' HOSE
30" SOFT
HOSE
7.5' SOFT
HOSE

LEGEND® PLATINUM INSTALLATION MANUAL
5/31/06 P/N YYPLATINSTALL REV. C
© Pentair Water Pool and Spa, Inc. All rights reserved.
Printed in USA.