BWT BC 30 User manual

MAINTENANCE & CLEANING
0 2021/02 :
A
USER MANUAL
MANUEL D’UTILISATION
BEDIENUNGSANLEITUNG
RECHARGEABLE
POOL & SPA VACUUM
ASPIRATEUR PISCINE
ET SPAS
RECHARGEABLE
WIEDERAUFLADBAR
ER POOLSAUGER

MAINTENANCE & CLEANING
1
2021/02 : A
Table Of Contents
SAFETY WARNINGS & INSTRUCTIONS P.
GETTING STARTED P.
Charging The Battery P.
Set-Up Before Use P.
Telescopic pole connector assembly P.
Telescopic pole (not included) assembly P.
Suction head / corner nozzle assembly P.
Pool Preparation P.
OPERATION P.
EMPTYING THE FILTER P.
MAINTENANCE & STORAGE P.
BATTERY DISPOSAL P.
How to remove the battery pack P.
TROUBLESHOOTING P.
Remark: Product/parts photos/drawings in this manual are for demonstration only.
Product/parts in photos/drawings may vary with the model purchased.
Accessories / parts shown in this manual are not necessarily included with every
model.

MAINTENANCE & CLEANING
2
2021/02 : A
Table des matières
AVERTISSEMENTS DE SÉCURITÉ ET
INSTRUCTIONS
P.
DÉBUT DES OPÉRATIONS P.
Chargement de la batterie P.
Réglage avant l’utilisation P.
Montage du connecteur de manche télescopique P.
Montage du manche télescopique (non inclus) P.
Assemblage de la tête d’aspiration/ manchette
d’aspiration d’angle
P.
Préparation de la piscine P.
FONCTIONNEMENT P.
VIDER LE FILTRE P.
ENTRETIEN ET STOCKAGE P.
MISE AU REBUT DE LA BATTERIE P.
Comment retirer le bloc de batteries P.
DEPANNAGE P.
Remarque: Les photos / dessins de produits / pièces de ce manuel sont uniquement à
titre de démonstration. Le produit / les pièces dans les photos / dessins peuvent varier
en fonction du modèle acheté
Tous les accessoires / pièces illustrés dans ce manuel ne sont pas inclus avec
chaque modèle

MAINTENANCE & CLEANING
3
2021/02 : A
Inhaltsverzeichnis
SICHERHEITSWARNUNGEN UND -HINWEISE S.
ERSTE SCHRITTE S.
Laden der Batterie S.
Vorbereitung vor der Benutzung S.
Montage Teleskopstangenkupplung/Griff S.
Montage der Teleskopstange(nicht inbegriffen) S.
Montage des Saugkopfs / Eckdüse S.
Vorbereitung des Beckens S.
BETRIEB S.
ENTLEEREN DES FILTERS S.
INSTANDHALTUNG UND LAGERUNG S.
ENTSORGUNG DES AKKUS S.
Entfernen den Akku S.
FEHLERBEHEBUNG S.
Kommentare Produkte/Teile auf den Fotos/Zeichnungen in dieser Anleitung dienen nur
zur Veranschaulichung. Produkte/Teile auf den Fotos/Zeichnungen können beim
gekauften Artikel variieren.
Das in dieser Anleitung gezeigte Zubehör/Teile sind nicht unbedingt bei jedem
Modell enthalten.

MAINTENANCE & CLEANING
4
2021/02 : A
SAFETY WARNINGS & INSTRUCTIONS
Information contained in this Instruction Manual will help you operate the item safely,
protect yourself and others from hazards, and prevent damage to the device and other
property.
SAVE THESE INSTRUCTIONS
WARNING!
- This is not a TOY. Children should be kept out of reach from this pool
vacuum and its accessories.
- Never allow children to operate this pool vacuum.
- This appliance is not intended for use by persons with reduced physical,
sensory, mental capabilities, or a lack of experience and knowledge,
unless they are given supervision or instructions concerning the safe use
of the appliance and understand the hazards involved by a person
responsible for their safety.
- Children must not play with this product.
- Cleaning and maintenance of the pool vacuum must not be carried out
by children.
- Make sure the pool vacuum is fully immersed in the pool before initiating
operation. The minimum water level required to operate the pool vacuum
must reach above the power ON/OFF switch of the pool vacuum when it
is held in a vertical position. Operating the pool vacuum when it is not
immersed correctly could damage the unit and void the warranty.
- Maximum operating depth in water is 3 meters (10ft).
- Maximum water temperature: 5˚C (41˚F) –35˚C (95˚F).
- Detachable supply unit (external adaptor).
- The pool vacuum should only be recharged with the external adaptor and
charging base delivered with this product.
- For the purposes of recharging the battery, only use the detachable
supply unit (external adaptor model number: DSS12D-0841000-B /
DSS12D-0841000-C / DSS12D-0841000-D/ LX084100U) that provided
with this pool vacuum to charge the battery.
- Connect the external adaptor to a power source through a residential
current device (RCD) / a ground fault circuit interrupter (GFCI). If in doubt,
consult a qualified electrician.
- Do not use this pool vacuum if any damage is detected.
- Replace damaged parts with ones that are certified by the distributor or
manufacturer.
- Turn off the power, disconnect the external adaptor from the power
source, and unplug the external adaptor from the charging base before
detaching the pool vacuum from the charging base.
- Disconnect the pool vacuum from the supply mains and make sure the
pool vacuum is OFF prior to carrying out regular maintenance – such as
cleaning the filter and the charging contact plates.
- Do not attempt to replace the installed rechargeable Li-ion battery pack.
- DO NOT handle the pool vacuum, external adaptor, and charging base

MAINTENANCE & CLEANING
5
2021/02 : A
while it is charging with wet limbs and without shoes.
- You should not operate this pool vacuum when people/pets are present
in the water.
- DO NOT use this pool vacuum without an intact fitler cage in place, as
your warranty will be voided as a result.
- Suction entrapment hazard: This pool vacuum generates suction. Do not
allow hair, body, or any loose parts of your clothing to make contact with
the suction hole of the pool vacuum during its operation.
- Never insert body parts, clothing or other objects into the openings and
moving parts of the pool vacuum.
- DO NOT use this pool vacuum to pick up any toxic substance, flammable,
and combustible liquids (i.e. gasoline) in the presence of explosive or
flammable fumes.
- Under no circumstances should you attempt to disassemble the pool
vacuum and replace the impeller, motor, and battery by yourself.
- Never insert fingers or any object to touch the impeller.
- The built-in battery must be removed by a skilled technician before it is
scrapped.
- This pool vacumm contains a battery that are only to be removed by
skilled persons.
- The pool vacumm must be disconnected from the supply mains as the
battery is removed.
- For details regarding battery recycling/disposal, refer to the section
“BATTERY DISPOSAL” in this manual and contact your local authorities
for more information.
- The battery must be disposed safely in accordance with local ordinances
or regulations.
- External adaptor and charging base:
Never use the external adaptor and charging base for anything
other than charging the battery of the pool vacuum that is
supplied in the same pack.
The external adaptor and charging base should not be used
outdoors, nor should it be exposed to rain, humidity, and any
liquid or heat.
The transformer (or external adaptor) is to be located outside
zone 1
Keep the external adaptor and charging base out of reach of
children.
Never use the external adaptor and charging base if any damage
is detected.
DO NOT handle the external adaptor and charging base with wet
hands.
DO NOT handle the pool vacuum, external adaptor, and charging
base while charging with wet hands and without shoes.

MAINTENANCE & CLEANING
6
2021/02 : A
Keep the external adaptor disconnected from power when it is
not in use.
Never attempt to open the external adaptor and charging base.
If the supply cord of the external adaptor is damaged, the external
adaptor must be replaced by the manufacturer or its service
agent to prevent hazards of any kind.
Make sure the pool vacuum and the charging base are
completely dry before charging.
CAUTION!
-This pool vacuum is designed for underwater use only; it is not an all-
purpose vacuum cleaner. DO NOT attempt to use it to clean anything other
than your pool / spa.
-Use only original accessories delivered with this product.
-DO NOT use this pool vacuum right after pool-shocking. It is recommended
to leave the pool circulating for at least 24-48 hours.
-If you are planning on using the pool vacuum in a saltwater pool, make sure
all salt are dissolved before deploying the pool vacuum.
-DO NOT use this pool vacuum with another automatic cleaner/cleaner
simultaneously in the pool/spa.
-Avoid picking up hard, sharp objects with this product. They may damage
the pool vacuum and filter.
-Exercise caution when cleaning pool stairs.
-To avoid damages to the external adaptor and charging base, do not
attempt to carry the pool vacuum by the cord of external adaptor / charging
base or pull the cord to disconnect it from the power source andcharging
base.
-Charge the pool vacuum indoor in a clean, dry area with good ventilation
and an ambient temperature between 5˚C (41˚F) and 35˚C (95˚F).
-DO NOT leave the pool vacuum charged for over 10 hours.
-If the pool vacuum will not be used for an extended period, detach it from
the charging base and use a damp cloth to clean and dry the pool vacuum
and accessories. Make sure to charge the pool vacuum to about 30% to
50% of the battery capacity before it is stored. Store in a well-ventilated
area away from sunlight, heat, ignition sources, pool chemicals, and
children. Never leave the pool vacuum plugged in for long-term storage.
Recharge the pool vacuum every three months.
Above warnings and cautions are not intended to incorporate all possible
instances for risks and / or severe injuries. Pool / spa owners should always
exercise extra caution and common sense when utilizing the product.

MAINTENANCE & CLEANING
7
2021/02 : A
GETTING STARTED
Charging the battery
IMPORTANT NOTE: Fully charge the pool vacuum (about 6 hrs) before using
it for the first time.
WARNING!
Use only the original external adaptor and charging base provided.
Make sure the pool vacuum and the charging contact plates are clean
and dry before set-up and charging. (TIPS: Use a cotton bud to dry the
charging contact plates)
Charging must be done indoors, in a well-ventilated area away from
sunlight, children, heat, ignition sources, and with an ambient
temperature between 5˚C (41˚F) and 35˚C (95˚F).
Never use the external adaptor and charging base if any damage is
detected.
The charging contact plates are waterproof. However, remnants of
water on the contact plates could result in natural occurrence of stains
(a byproduct of chemical reaction between water and electric currents).
Otherwise, the stains can be removed by light scrubbing with a cotton
bud soaked with juice of lemon or vinegar.
Make sure that the pool vacuum is turned off prior to charging.
1. Place the unit on a flat surface. Make sure the pool vacuum is off by
turning the power ON/OFF switch to the OFF position prior to charging.
2. Align and slide the hook of the charging base onto the side notch at the
bottom of the main body until it stops. Make sure their contact plates are
properly in contact.

MAINTENANCE & CLEANING
8
2021/02 : A
3. Plug the jack of the external adaptor into the charging port at the end of
the charging base.
4. Connect the external adaptor to the power source. Once the pool vacuum
begins charging, the indicator light on the external adaptor will turn red.
Normally, it takes about 4-6 hours to reach a full charge. The indicator
light will turn green when the pool vacuum is almost fully charged.
NOTE: if the motor is generating noise, ensure “OFF” is selected on the
power switch.
Immediately disconnect the external adaptor from the power source if you
detect any of the following:
- Offensive or unusual odor
- Excessive heat
- Deformation, cracks, leaks
- Smoke
5. When charging is complete, disconnect the external adaptor from the
power source and detach the charging base from the unit and external
adaptor.
Normally, the pool vacuum can operat up to 30 minutes on a full charge (charged for 4-6
hours)
Note: Clean the filter cage regularly. Excessive debris inside the filter cage increases the
burden to the motor operation and shortens the operating duration as a result.
FACT: Rechargeable lithium-Ion battery is classified as a consumable item. It has a limited
life and will gradually lose its capacity to hold a charge. Therefore, running time of the
pool vacuum will gradually reduce through repeated charging and discharging in operation.
Once the lifespan of the battery reaches its end, refer to section “BATTERY DISPOSAL”
for instructions regarding battery disposal.

MAINTENANCE & CLEANING
9
2021/02 : A
NOTE: Let the pool vacuum rest for 30 to 40 minutes before charging it again.
Set-Up Before Use
Telescopic pole connector assembly
Press down the side pins of the connector and insert it inside the main body. Turn the
connector in either direction until the pin is secured in the hole, as shown in the diagram.
Telescopic pole (not included) assembly
Note: a V-clip is installed inside the pole connector to secure the telescopic pole (not
included) in position. Slide the telescopic pole onto the pole connector. Press on the side
pins of the connector and slide the telescopic pole further down until the pins of the
connector are secured inside the holes of the pole.
To release the telescopic pole, press down the side pins simultaneously and pull out the
pole.
Suction head/corner nozzle assembly
Insert the suction head directly into the suction mouth of the pool vacuum until the side
tabs of the transparent canister clip in the side holes of the suction head.

MAINTENANCE & CLEANING
10
2021/02 : A
NOTE: To replace the brushes on the suction head, lift one end and pull the brush out to
make space for a new one.
WARNING! For vinyl liner and fibreglass pools, it is recommended to keep the brushes
on the suction head to avoid damaging the pool.
Pool Preparation
-If there are stones, roots or metal corrosion in contact with the underside of the
liner, discard them prior to using the pool vacuum. If necessary, seek assistance
from a qualified professional.
-If the liner is brittle, damaged or wrinkled, contact a qualified professional to
perform the necessary repairs or perform a liner replacement prior to using the
pool vacuum.
-If you are using a saltwater pool, make sure all salt are dissolved before placing
the pool vacuum into the water.
OPERATION
WARNING!
Make sure the pool vacuum is off
Do not use the pool vacuum if any damage is detected.
Oil stain could occur due to possible leakage of lubricants applied to the
O-ring.

MAINTENANCE & CLEANING
11
2021/02 : A
Do not operate this pool vacuum if there are people/pets present in the
water.
Make sure the pool vacuum is fully immersed in the pool before initiating
operation. The minimum water level required to operate the pool vacuum
must reach above the power ON/OFF switch of the pool vacuum when it
is held in a vertical position. Operating the pool vacuum when it is not
immersed correctly could damage the unit and void the warranty.
DO NOT use the pool vacuum without an intact filter cage in place. Using
your pool vacuum without an intact filter cage in place will VOID your
warranty.
DO NOT leave the pool vacuum in the water when it is not in use.
1) Bring your pool vacuum to the side of your pool / spa. Immerse the pool vacuum in
water and turn the power ON/OFF switch to the ON position to initiate operation.
CAUTION! Make sure the pool vacuum is always facing downwards when it is placed into
the pool. Otherwise it may bend the pole connector and damage it during the process.
2) To remove the pool vacuum from the pool / spa, lift the pool vacuum while pointing it
downwards in order to allow water to escape from the outlet valve. Water is going to
escape via the pole connector and draining holes inside the connector chamber on the
rear body.
CAUTION! Make sure the pool vacuum is always facing downwards when it is removed
from the pool. Otherwise, the pole connector may be bent and damage the pool vacuum
in the process.
3) Rinse the pool vacuum with fresh water after every use. DO NOT use any detergent.
EMPTYING THE FILTER
WARNING! Using the pool vacuum without a filter cage in place will
VOID your warranty.
In order to maximize the cleaning efficiency, be sure to clean the filter cage before and
after each use.
CAUTION! If the pool vacuum is charging, disconnect the external adaptor from the power
source and detach the pool vacuum from the charging base. Make sure the pool vacuum
is OFF
Emptying the filter cage
1. Place the pool vacuum on a stable surface.
2. Press the locking button until the locking hole on the clear canister is released. Slide
the canister away until the notch on the bottom of canister opening is released from
the hook on the bottom of main body. Remove the filter cage from the main body.

MAINTENANCE & CLEANING
12
2021/02 : A
CAUTION! Replace the damaged filter cage immediately before the next operation.
3. Clean out the debris and rinse the filter cage with water. If brushing is deemed
necessary, use only a soft brush to clean the filter cage gently and carefully.
To re-install the canister, first align the notch of the canister with the hook on main body
and then press the canister onto main body. Make sure the locking hole on the clear
canister is secured with the locking button.
MAINTENANCE & STORAGE
NOTE:
1. Be sure to clean and dry the charging contact plates after every use to avoid the
forming of stains (byproduct of a natural chemical reaction between electric current
and water). Otherwise, the stains can be removed by light scrubbing with a cotton bud
soaked with juice of lemon or vinegar.
2. Battery discharges on its own during storage. Make sure to charge the pool vacuum
to about 30% to 50% of the battery capacity before it is stored.
3. You must re-charge the battery at least once every three months when it is not in use.
Unplug the external adaptor from socket and then unplug the adapter jack from the
charging base.
Detach accessories from the pool vacuum. If necessary, rinse the pool vacuum and
accessories with fresh water. DO NOT use detergent.
Make sure to drain the water from the unit and pole connector.
Use a damp cloth to clean and dry the pool vacuum and its accessories.
Store them in a well-ventilated area away from the sunlight, children, heat, ignition
sources, and pool chemicals. Ambient temperature for storage should be 10˚C – 25˚C
(50˚F – 77˚F). NOTE: A higher temperature may reduce the battery life during storage.

WARNING!
-Never attempt in any way to disassemble the pool vacuum.

MAINTENANCE & CLEANING
13
2021/02 : A
-Under no circumstances should you attempt to disassemble the pool
vacuum and replace the impeller, motor and battery by yourself.
CAUTION!
Excessive heat can damage the battery and reduce its lifespan as a result.
Consult your dealer regarding battery replacement if the following happens:
-Battery does not charge fully.
- Battery operation time is noticeably reduced. Observe and record the run times of the
first few operations (on a full charge). Use these run times as a reference point for
comparison with run times in the future.
The battery must be removed from the pool vacuum before it is scrapped.
The pool vacuum must be disconnected from the supply mains when removing the
battery
The battery is to be disposed safely and according to local ordinances or regulations.
NOTE: Incorrect maintenance may reduce the battery life and affect its capacity as a
result.
BATTERY DISPOSAL (To be carried out by an authorized technician)
Your pool vacuum battery is a maintenance-free rechargeable lithium-ion battery
pack, which must be disposed properly. Recycling is required; please contact your
local authority for information.
WARNING!Never attempt to disassemble a battery pack
Remove all personal items such as rings, bracelets, necklaces and
watches when the battery pack is unwired from the pool vacuum.
A battery can produce a short circuit current high enough to weld a ring
(or similar item) to metal, causing a severe burn in the process.
Wear complete eye protection, gloves and protective clothing when the
battery pack is being removed.
Avoid touching the wires altogether and avoid allowing them to make
contact with any metal items, which could cause sparking and/or short
circuit the battery.
Never smoke or allow a spark or flame in the vicinity of the battery or the
pool vacuum.
Do not expose the battery to fire or intense heat as this may result in an
explosion.

CAUTION!
If a battery leak occurs, avoid contact with the leaking fluids and place the damaged
battery in a plastic bag.
-If leaking fluids come in contact with skin and clothing, wash immediately with plenty
of soap and water.
-If leaking fluids come in contact with eyes, immediately flush eyes with cool running
water for at least 15 minutes and do not rub them. Seek medical attention as soon as
possible.

MAINTENANCE & CLEANING
14
2021/02 : A
How to remove the battery pack for battery disposal only (To be done by
authorized technician)
Recommended tools (not included): Phillips screwdriver and small slot
screwdriver
1. Press on the locking button and detach the clear canister from the body.
Use a small screwdriver to detach the ring from the body. It is hard to detach
the ring by screwdriver, use cutting plier to cut.
2. Use Philips screwdriver to unscrew all the screws on the main body.
3. Separate the body in two halves to access the main chamber. Use a
Philips screwdriver to remove the end cover and access the battery pack.
4. Use Philips screwdriver to unscrew screw on the corner of the supporting
plate as pointed at. Use clamp to catch the plate and pull it out to expose
the wire connectors on the PCB.

MAINTENANCE & CLEANING
15
2021/02 : A
5. Locate the middle connector as indicated, press the clip on the connector
and pull it out. NOTE: Wrap the connector immediately with insulating tape
in order to avoid short circuit caused by the contact of both wire terminals.

MAINTENANCE & CLEANING
16
2021/02 : A
TROUBLESHOOTING
Problem
Possible Cause
Solution
Pool vacuum does not capture
debris
Battery is running out
Charge the battery again.
Impeller is jammed
Power off the pool vacuum and visually check the gap
in the middle of the pool vacuum to see if the impeller
is jammed by large debris. If possible, use a small
tool to remove the debris carefully. If necessary,
contact your dealer for further instructions.
WARNING! Make sure the pool vacuum is
powered off when the unit is being serviced.
Impeller is broken
Contact your dealer for impeller replacement.
Filter cage is full
Clean the filter cage.
Debris escapes from the filter
Suction nozzle flap is
broken
Suction nozzle flap works like a door to prevent debris
from escaping from the filter. Contact dealer for
replacement part and instructions.
Filter cage is damaged.
Replace with a new filter cage.
Outlet valve comes off.
Without the outlet valve, the pool vacuum might
capture debris through this opening. Contact dealer
for a valve replacement.
Telescopic pole connector
cannot be secured in assembly
Side pin on the
connector is broken
Replace with a new telescopic pole connector.
Pool vacuum is activated even
though the switch indicates it’s
off.
Presence of magnetic
objects nearby has
inadvertently switched
on the motor.
Move the magnetic objects or vacuum away from
each other.
Pool vacuum cannot be
charged / recharged
Battery is damaged
Contact dealer for battery replacement.
WARNING! DO NOT open the pool vacuum
and replace the battery by yourself. This could result
in severe or fatal injury and the warranty will be
voided as a result.
Charging plates on
charging base and pool
vacuum are not
contacted properly
Make sure that the charging base is assembled on
the pool vacuum completely and their contact plates
are contacted properly
External adaptor
damaged Contact dealer for replacement.
WARNING! Using the wrong external adaptor
will result in damaging the pool vacuum / battery and
voiding the warranty as a result.
Pool vacuum does not move
smoothly
Wheel is jammed
Clean out the debris from the wheel.
Operation time is shorter as
expected
Battery is not fully
charged
Charge the pool vacuum for at least 6 hrs. NOTE: if
any stains are found on the charging contact plates,
remove them by using a cotton bud soaked with
lemon juice or vinegar
Environmental Programmes, WEEE European Directive
Please respect the European Union regulations and help to protect the environment.
Return non-working electrical equipment to a facility appointed by your municipality that properly
recycles electrical and electronic equipment. Do not dispose them in unsorted waste bins. For
items containing removable batteries, remove batteries before disposing of the product.
© 2020
BWT Holding GmbH
20010021
All rights reserved. No part of this document may be reproduced or transmitted in any form or by
any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written
permission (V1)
If soft copy of this instruction manual is required, please contact our customer service by email.
SAVE THESE INSTRUCTIONS

MAINTENANCE & CLEANING
17
2021/02 : A
AVERTISSEMENTS DE SÉCURITÉ ET NSTRUCTIONS
Les informations contenues dans ce manuel d'instructions vous permettront d’utiliser
l’appareil en toute sécurité, à vous protéger ainsi que les autres et à éviter d'endommager
l'appareil ou d'autres biens.
CONSERVER CE MANUEL
AVERTISSEMENT !
- Ceci n’est pas un JOUET. Les enfants doivent être maintenus hors de la
portée de cet aspirateur de piscine et de ses accessoires.
- Ne jamais permettre aux enfants de faire fonctionner ce aspirateur de
piscine.
- Ce dispositif n'est pas destiné à être utilisé par des personnes ayant des
capacités physiques, sensorielles ou mentales diminuées, ou un manque
d'expérience et de connaissances, sauf si elles sont sous supervision ou
ont reçu des instructions concernant l'utilisation sûre de l'appareil par une
personne responsable de leur sécurité.
- Les enfants ne doivent pas jouer avec ce aspirateur de piscine..
- Le nettoyage et l'entretien du aspirateur de piscine ne doit pas être
effectués par des enfants.
- Assurez-vous que l’aspirateur de piscine est totalement immergé dans la
piscine avant de commencer l’opération. Le niveau d’eau minimum exigé
pour faire fonctionner l’aspirateur de piscine doit dépasser l’interrupteur
Marche / Arrêt de l’aspirateur de piscine lorsqu’il est maintenu en position
verticale. Faire fonctionner l’aspirateur de piscine lorsqu’il n’est pas
immergé correctement pourrait endommager l’unité et annuler la
garantie.
- La profondeur maximale de fonctionnement dans l’eau est de 3 mètres
(10 pieds).
- Température maximale de l’eau : 5˚C – 35˚C
- Unité d'alimentation détachable (transformateur).
- À l’effet de recharger la batterie, utiliser seulement l’unité d’alimentation
amovible (modèle transformateur : DSS12D-0841000-B / DSS12D-
0841000-C / DSS12D-0841000-D /LX084100U) qui est fourni avec cet
aspirateur de piscine pour charger la batterie.
- Pour recharger la batterie, utilisez uniquement l'unité d'alimentation
amovible (transformateur) fournie avec ce produit
- Connecter le transformateur à une source d'alimentation par
l'intermédiaire d'un dispositif différentiel à courant résiduel (DDR) ou d'un
disjoncteur de fuite à la terre (GFCI). En cas de doute, consultez un
électricien professionnel qualifié.
- Ne pas utiliser cet aspirateur de piscine si un dommage quelconque est
détecté.
- Remplacer les pièces endommagées avec des pièces certifiées par le
distributeur ou le fabricant.
- Mettre hors tension, débrancher le transformateur de la source
d’alimentation, et débrancher le transformateur de la base de
chargement avant de séparer l’aspirateur de piscine de la base de

MAINTENANCE & CLEANING
18
2021/02 : A
chargement.
- Débrancher l’aspirateur de piscine du réseau d’alimentation et s’assurer
que l’aspirateur de piscine est hors tension avant d’effectuer l’entretien
régulier – tel que le nettoyage du filtre et des plaques de contact de
chargement.
- Ne remplacez pas la batterie rechargeable Li-ion pré-installée.
- NE manipulez PAS le aspirateur de piscine, le transformateur et la base
de chargement pendant la charge avec des membres mouillés et sans
chaussures..
- Vous ne devrez pas faire fonctionner cet aspirateur de piscine lorsque
des personnes/animaux de compagnie sont présents dans l’eau.
- Ne pas utiliser cet aspirateur de piscine sans une cage de filtre intact en
place, car votre garantie serait annulée de ce fait.
- Danger de piégeage de l’aspiration : Cet aspirateur de piscine produit
une aspiration. Ne pas permettre que les cheveux, le corps, ou toutes
parties lâches de vos vêtements entrent en contact avec l’orifice
d’aspiration de l’aspirateur de piscine pendant son fonctionnement.
- Ne jamais introduire des parties du corps, vêtements ou autres objets
dans les ouvertures et pièces mobiles de l’aspirateur de piscine.
- NE PAS utiliser cet aspirateur de piscine pour ramasser des substances
toxiques, inflammables ou liquide combustibles (comme de l'essence),
ni en présence de vapeurs explosives ou inflammables.
- En aucun cas, vous ne devrez tenter de démonter l’aspirateur de piscine
et de remplacer la turbine, le moteur, et la batterie de par vous-même.
- Ne jamais insérer les doigts ou un quelconque objet dans la turbine.
- La batterie intégrée doit être retirée par un technicien qualifié avant d'être
mise au rebut.
- Cet aspirateur de piscine contient une batterie qui ne peut être retirée
que par des personnes qualifiées.
- L’aspirateur de piscine doit être déconnecté du réseau d'alimentation lors
du retrait de la batterie..
- Pour plus de détails sur la mise au rebus de la batterie veuillez vous
reporter à la section "MISE AU REBUT DE LA BATTERIE" de ce manuel
et contactez les autorités locales pour plus d'informations.
- La batterie doit être détruite en toute sécurité conformément aux
réglementations locales.
- Le transformateur et base de chargement :
Ne jamais utiliser le transformateur et la base de chargement pour tout
autre chose que le chargement de la batterie de l’aspirateur de piscine
qui est fournie dans le même bloc.
Le transformateur et la base de chargement ne doivent pas être
utilisés à l'extérieur, ni exposés à la pluie, à l'humidité et à tout liquide
ou chaleur.
Le transformateur doit être situé à l'extérieur de la zone 1
Maintenir le transformateur et la base de chargement hors de la portée
des enfants.

MAINTENANCE & CLEANING
19
2021/02 : A
Ne jamais utiliser le transformateur et la base de chargement si un
dommage quelconque est détecté.
NE PAS manipuler le transformateur et la base de chargement avec
des mains humides.
NE PAS manipuler l’aspirateur de piscine, le transformateur, et la base
de chargement pendant la charge avec des mains humides et sans
chaussures.
Maintenir le transformateur débranché du courant lorsqu’il n’est pas
utilisé.
Ne jamais tenter d’ouvrir le transformateur et la base de chargement.
Si le cordon d’alimentation du transformateur est endommagé, ce
transformateur doit être remplacé par le fabricant ou son agent de
service pour empêcher des dangers de toute nature.
S’assurer que l’aspirateur de piscine et la base de chargement sont
complètement secs avant de charger.
MISE EN GARDE !
- Cet aspirateur de piscine est uniquement conçu pour une utilisation sous l’eau ; il ne
s’agit pas d’un aspirateur tout usage. NE PAS tenter de l’utiliser pour nettoyer tout autre
chose que votre piscine / spa.
- Utiliser uniquement les accessoires originaux livrés avec ce produit.
- Ne pas utiliser cet aspirateur de piscine juste après le nettoyage chimique de la piscine.
Il est recommandé de laisser circuler l’eau dans la piscine durant au moins 24-48 heures.
- Pour les piscines d'eau salée, s’assurer que tout le sel est dissous avant de placer le
aspirateur de piscine dans l'eau.
- Ne pas utiliser cet aspirateur de piscine avec un autre aspirateur / nettoyeur électrique
simultanément.
- Éviter de ramasser des objets durs ou pointus avec ce aspirateur de piscine.. Ils peuvent
endommager l’aspirateur de piscine et le filtre.
- Prendre des précautions lors du nettoyage des marches de la piscine.
- Pour éviter d'endommager l transformateur et la base de chargement, ne tentez pas de
porter l’aspirateur de piscine par le cordon du transformateur / base de chargement et
ne tirez pas sur le cordon pour le débrancher de la source d’alimentation et de la base
de chargement..
- Charger l’aspirateur de piscine à l’intérieur dans une zone propre et sèche avec une
bonne aération et une température ambiante entre 5˚C et 35˚C.
- NE PAS laisser l’aspirateur de piscine chargé pendant plus de 10 heures.
- Si l’aspirateur de piscine n’est pas utilisé pendant une longue période de temps, le
séparer de la base de chargement et utiliser un chiffon humide pour nettoyer et sécher
l’aspirateur de piscine et ses accessoires. S’assurer de recharger l’aspirateur électrique
à 30%- 50% avant de le stocker. Le ranger dans une zone bien aérée éloignée de la
lumière solaire, de la chaleur, des sources d’ignition, des produits chimiques pour la
piscine et des enfants. Ne jamais laisser l’aspirateur de piscine branché pour un
stockage à long terme. Recharger l’aspirateur de piscine tous les trois mois.
Les avertissements et mises en garde ci-dessus ne prétendent pas inclure tous les
possibles cas de risques et / ou de blessures graves. Les propriétaires de piscine /
spas doivent toujours prendre des précautions supplémentaires et utiliser leur bon sens
lorsqu’ils utilisent le produit.