Pentair HYDROMATIC 118-5 Manual

Sump Pump Hide-Away Basin System
(14.5" W, 16" H, 1.5" Discharge Opening)
118-5 SYSTEM
NOTE! To the installer: Please make sure you provide
this manual to the owner of the pumping equipment or
to the responsible party who maintains the system.
Pump System Installation and Service Manual

2
Thank you for purchasing your
Hydromatic®product. To help ensure
years of trouble-free operation, please
read the following manual carefully.
Before operation:
Read the following instructions
carefully. Reasonable care and safe
methods should be practiced. Check
local codes and requirements before
installation.
Attention:
This manual contains important
information for the safe use of this
product. Read this manual completely
before using this product and refer to
it often for continued safe product
use. DO NOT THROW AWAY OR
LOSE THIS MANUAL. Keep it in a
safe place so that you may refer to it
often.
Warning:
Before handling these pumps and
controls, always disconnect the power
first. Do not smoke or use
sparkable electrical devices or flames
in a septic (gaseous) or possible
septic sump.
Warranty void if product is
modified, drilled, painted, or altered
in any way; if used to pump
hot water, or to pump liquids other
than water (such as but not limited to
chemicals, fertilizers, flammable
liquids, herbicides, mud, tar, cement,
wood chips); or otherwise abused.
The model 118-5 Hide-Away Basin
System is specially designed for
pumping wastewater from laundry
General
Information
Pump
Warning
using 1-1/2" or 1-1/4" PVC pipe on
the discharge line, a Hydromatic
CV-170 check valve is recommend-
ed. Once check valve has been
installed, plumb the discharge line
into an existing drain line.
Basin:
Hydromatic’s 118-5 Hide-Away
Basin System includes a corrosion-
resistant polypropylene tank with a
gasket cover. An inlet strainer is pro-
vided in the basin cover above the
inlet. The strainer is sealed and held
in place with the four screws provided.
Installation
Instructions
Electrical
Information
Diagram 1 shows the various
connections that must be made for
proper installation and operation.
This is only a guide; actual
installation may vary depending on
the particular situation.
Inlet:
A 1-1/2" inlet is provided on the
118-5 Hide-Away Basin System. One
method of hookup is to use a 1-1/2"
PVC MIP adapter or a 1-1/2" PVC
MIP marvel connection (or a similar
type of connection). You may use a
1-1/2" extension tailpiece or 1-1/2"
PVC pipe; it depends on the type of
fittings used on the basin inlet. The
P-Trap should be installed once the
appropriate connections are made on
the basin inlet. Once these fittings are
installed the rest of the piping may be
plumbed.
Vent:
Provision has been made for a 2" vent
to allow maximum volume for any
application and proper operation of
pump. The vent may be reduced to no
less than 1-1/4". Venting is essential
for proper pump operation and should
not be omitted. The 118-5 Hide-Away
Basin System may be vented into an
existing vent stack or use a BOCA in-
line vent. Check local codes.
Discharge:
Do not restrict discharge line below
1-1/4". A check valve MUST be
installed to prevent backflow of
water after each cycle. If you are
Caution:
Always disconnect pump from the
electrical power source before doing
any maintenance. Your sink pump
system is manufactured for easy
maintenance. Each unit is
individually factory-tested to ensure
proper adjustment and operation.
If unit fails to operate properly,
carefully read instructions again to
make sure correct procedure has been
followed.
Note: The basin strainer requires
routine maintenance. The strainer
should be removed and cleaned
monthly to prevent clogging.
WARNING! Risk of electrical
shock. This pump is supplied with a
grounding conductor and grounding
type attachment plug. To reduce risk
of electrical shock, connect only to a
properly grounded grounding-type
receptacle. This pump has not been
investigated for use in swimming
pool areas.
trays, washing machines, wet bars,
water softeners, dehumidifiers, etc.
This pump system installs above
floor level, no need to dig a sump!
This pump system cannot be used for
laundry/dishwasher applications in a
commercial or industrial environment.
System
Maintenance

3
DO NOT WORK ON PUMP
UNTIL POWER IS
UNPLUGGED.
DO NOT cut off ground pin or use an
adapter fitting. DO NOT use an
extension cord. The pump power
cord should be connected to a
separately fused, grounded 115 volt
line with a minimum capacity of 15
amps. NEVER touch the pump when
it is connected to electrical power.
The receptacle should be located at
least 4 feet above floor level.
When wiring this pump follow all
local electrical and safety codes and
ordinances as well as the most recent
National Electrical Code.
N.E.C., ANSI/NFPA 70 - 2000.
118-5
Parts List
Inlet Pipe
and Trap
(not supplied)
Laundry Tray
Wet Bar
Dehumidifier
Water Softener
Washing Machine
etc. (not supplied)
Pump, Switch and
Internal Piping
Tank
Gas-tight
Cover
Discharge Pipe
and Check Valve
(not supplied)
Vent Pipe
(not included)
Inlet
Opening
Discharge
Opening
Clean-out
Filter
Vent
Opening
Pipe
Included
11/2"
11/2"
141/2"
2"
11"
16"
Ref. No. Description Part No. Qty.
1 BASIN, SINK TANK 25530C000 1
2 BV-A1, SUMP PUMP 52623-000-1 1
3 COVER, SINK BASIN 25540C001 1
4 GASKET, COVER 23150074000 3.38
5 SCREW, 10-32 X 3/4" PANHEAD PHILLIPS 05434A061 8
6 COVER, SINK TANK STRAINER 25686A000 1
7 GASKET, STRAINER 25688B000 1
8 STRAINER 25685A000 1
9 FASTENERS, 1/4-20 X 5/8" 18475A007 4
10 PIPE, 1-1/2 X 12" TOE 13665-018-3 1
11 GROMMET, ELECTRICAL 25689A000 1
12 NAMEPLATE 14849-000-1 1
13 LABEL, WARNING 14848-000-1 1
14 CARTON 14851-000-1 1
Diagram 1

Item # E-03-423 5/07Part # 5625-423-1
WARRANTY
Hydromatic®warrants to the original purchaser of each Hydromatic product(s) that any part
thereof that proves to be defective in material or workmanship within one year from date of installation or
18 months from manufacture date, whichever comes first, will be replaced at no charge with a new or
remanufactured part, F.O.B. factory. Purchaser shall assume all responsibility and expense from removal,
reinstallation and freight. Any item(s) designated as manufactured by others shall be covered only by the
express warranty of the manufacturer thereof. This warranty does not apply to damage resulting from
accident, alteration, design, misuse or abuse. The pump must be installed, operated and maintained in
accordance with the published instructions of the appropriate Installation & Service Manual.
All dual seal non-clogs and 3–5 HP grinders must have seal failure and heat sensors attached and functional
for Warranty to be in effect. If a seal failure should occur, Hydromatic will cover only the lower seal and labor
thereof. Labor is based on Authorized Service Center contract allowance. If the heat sensor is not attached
and functional, Warranty is void. If the seal failure sensor is not attached and functional, Warranty is void.
If the material furnished to the Buyer shall fail to conform to this contract or to any of the terms of this
written warranty, Hydromatic shall replace such nonconforming material at the original point
of delivery and shall furnish instruction for its disposition. Any transportation charges involved in such
disposition shall be for the Buyer’s account. The Buyer’s exclusive and sole remedy on account or in respect
of the furnishing of material that does not conform to this contract or to this written warranty, shall be to
secure replacement thereof as aforesaid. Hydromatic shall not in any event be liable for the cost of any labor
expended on any such material or for any incidental or consequential damages to anyone by
reason of the fact that such material does not conform to this contract or to this written warranty.
ALL IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY
AND THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE DISCLAIMED
TO THE SAME EXTENT AS THE EXPRESS WARRANTY CONTAINED HEREIN. Some states do not
allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
MANUFACTURER EXPRESSLY DISCLAIMS AND EXCLUDES ANY LIABILITY FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED
WARRANTY ARISING IN CONNECTION WITH THIS PRODUCT, INCLUDING WITHOUT
LIMITATION, WHETHER IN TORT, NEGLIGENCE, STRICT LIABILITY CONTRACT OR
OTHERWISE. Some states do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state.
– Your Authorized Local Distributor –
USA
740 East 9th Street, Ashland, Ohio 44805
Tel: [phone] Fax: [phone] www.hydromatic.com
CANADA
269 Trillium Drive, Kitchener, Ontario, Canada N2G 4W5
Tel: [phone] Fax: [phone]
© 2007 Hydromatic®Ashland, Ohio. All Rights Reserved.