Pentair HYPRO 9306C Series User manual

KEEP FOR FUTURE REFERENCE
pentair.com
INSTALLATION AND
OPERATION MANUAL
CAST IRON & STAINLESS STEEL SERIES
9306C 9306S
L-1546 Rev. E (12-09-19) Pentair 375 5th Ave. NW, New Brighton, MN 55112 Phone: [phone] -OR- 800-424-9776 Fax: [phone] www.pentair.com
EC REP
EU Authorized Representative:
QNET BV Hommerterweg 286 6436 AM Amstenrade, The Netherlands KvK Zuid-Limburg 14091511

L-1546 (Rev E) -2-
Contents
EU Language Manuals............................................................................................................................................................3
Introduction.................................................................................................................................................................4
Description.....................................................................................................................................................4
Intended Uses............................................................................................................................................................4
Purpose of Manual....................................................................................................................................................4
Misuses...........................................................................................................................................................5
 PumpIdentication.....................................................................................................................................................5
Pump Technical Data..............................................................................................................................................................6
Fluid Pumping Applications......................................................................................................................................10
Tools................................................................................................................................................................10
Lifting,Transport, and Intermediate Storage...............................................................................................................10
Assembly and Installation......................................................................................................................................................11
Assembly.......................................................................................................................................11
Installation...................................................................................................................................11
Control Systems.......................................................................................................................................................13
Commissioning Start-Up, Operation, Shutdown..................................................................................................................14
Information.............................................................................................................................................14
Start-Up, Operation, Shutdown...............................................................................................................................14
Maintenance and Servicing..................................................................................................................................................16
Information............................................................................................................................16
Disposal.................................................................................................................16
Cleaning.................................................................................................................16
Maintenance, Routine Servicing, and Inspection.....................................................................................................17
Troubleshooting.....................................................................................................................17
Replacement Parts...................................................................................................................................................18
Declaration of Incorporation.................................................................................................................................................19
Warranty. ..................................................................................................................................................................Last page

L-1546 (Rev E)-3-
EU Language Manuals
DO NOT attempt to install or operate your pump before reading the manual. Original copies of the manual for Hypro
pumpsareprovidedinEnglish.Tondacopyinyournativelanguage,gotowww.hypropumps.com.
Vor dem Ablesen des Handbuches versuchen Sie NICHT, Ihre Pumpe zu installieren. Originale des Handbuches fur
Hypro-PumpenwerdenaufenglischzurVerfugunggestellt.ZueineKopieinIhrerMuttersprachenden,zu
www.hypropumps.com zu gehen (German)
N’essayez pas d’installer votre pompe avant de lire le manuel. Des exemplaires originaux du manuel pour des pompes
de Hypro sont fournis en anglais. Pour trouver une copie dans votre langue maternelle pour aller a
www.hypropumps.com (French)
NON tentare di installare la vostra pompa prima di leggere il manuale. Esemplare originale del manuale per Hypro
pompe sono in inglese. Per trovare una copia nella vostra lingua andare a www.hypropumps.com (Italian)
Непытайтесьустановитьвашнасосдочтенияруководства.Оригинальныекопииэтогоруководствадлянасосы
Hyproнаанглийскомязыке.Найтикопиюнавашроднойязыкперейтикwww.hypropumps.com(Russian)
NO intente instalar su bomba antes de leer el manual. Copias originales del manual para Hypro se provee de bombas
en ingles. Para encontrar una copia en tu idioma nativo ir a www.hypropumps.com (Spanish)
NIEprobowaćinstalowaćpompyprzedjejodczytanieminstrukcji.OryginalnekopieinstrukcjiobsługipompHyprosą
dostarczanewjęzykuangielskim.Abyuzyskaćkopięwtwoimojczystymjęzykuprzejdźdowww.hypropumps.com
(Polish)
Takmayacalışmayınokumadanoncepompanınmanuel.OrijinalkopyalarınıHypropompalarıicinIngilizceolarak
sunulmuştur.Birkopyasınıbulmakicinyereldilgitwww.hypropumps.com(Turkish)
Nao tente instalar a bomba antes de ler o manual. As copias originais dos manuais para Hypro bombas sao
fornecidos em Ingles. Para encontrar uma copia em sua lingua nativa ir para www.hypropumps.com (Portuguese)
VERGEETNIETuwpompvoorhetlezenvanhethandboek.ExemplarenvandehandleidingvoorHypropompenzijn
beschikbaarinhetEngels.Opzoeknaareenexemplaarinuweigentaalganaarwww.hypropumps.com(Dutch)

L-1546 (Rev E) -4-
Introduction
Description
Hyprocentrifugalpumpsaredesignedforcreatingandboostingpressureinuidcircuits.Thepumpoperatesbytaking
inuidfromtheinletportafterwhichitisslungbytheimpellerandexpelledthroughtheoutletport.Constructionfeatures
include housings, impellers and seals which come in a variety of materials in order to be resistant to a range of chemicals.
Standardmodelsofcentrifugalpumpsrotateclockwise,whenlookingattheshaftendofthepump.
Intended Uses
Hyprocentrifugalpumpsareintendedforcreatingorboostingdynamicpressureinapproveduids.Hyprocentrifugal
pumps should never be used to pump liquids above 140°F (60°C), or below 34°F (1°C). For pumps equipped with
hydraulic motors, the pump should not be run if the hydraulic oil temperature exceeds 135°F (57°C). Any uses outside
ofthosespeciedinthismanualareconsideredmisusesandareprohibited.ContactHyprotechnicalservicewithany
questionsregardingspecicacceptableuses.
Purpose of Manual
Hypro has provided this manual to provide instructions and requirements that must be met when installing, using and
maintaining the product(s) included in this document.
If the product is sold, the seller must pass this manual onto the new owner.
The following special attention notices are used to notify and advise, the user of this product, of procedures that may be
dangerous to the user or result in damage to the product.
ATTENTION
Attention is used to notify of installation, operation, or maintenance information that is important but not safety related.
Thissymbolisusedtodenotethepresenceofanelectricalhazardthatwillresultinpersonalinjury,deathorproperty
damage.
Thissymbolisusedtodenotethepresenceofahazardthatwillresultinpersonalinjury,deathorpropertydamage.
California Proposition 65 Warning --Thisproductandrelatedaccessoriescontainchemicalsknowntothe
State of California to cause cancer, birth defects or other reproductive harm.

L-1546 (Rev E)-5-
Misuses
Hyprocentrifugalpumpsaredesignedtooperateeffectivelywithinthespeciedspeed,pressureandenvironmental
ranges.Goingoutsideoftheserangeswillvoidthewarrantyandcouldcausedamagetoproperty,seriousinjury,ordeath.
• DO NOTrunthepumpfasterthanthemaximumspeciedspeed.
• DO NOTrunthepumphigherthanthemaximumspeciedpressure.
• DO NOT run pumps when the liquid has exceeded the maximum or minimum temperature limit (see Intended Uses).
• DO NOT pump non-approved liquids.
• DO NOT pump water or other liquids for human consumption.
• DO NOToperateanyHypropumpundertheinuenceofdrugsoralcohol.
• DO NOT run the pump dry.
• DO NOTrunthepumphydraulicmotorhigherthanthespeciedRPM,pressureorow.
Pump Identication
Hypro uses serialized labeling to enable users to precisely identify the pump’s manufacturing date.
Serial Number:
First and second digits: year (14 = 2014)
Third through fth digits: consecutive day of the year the pump was manufactured.
Sixth through tenth digits: unique pump serial number.

L-1546 (Rev E) -6-
Pump Technical Data
(Allspecicationsandperformancedataarebasedonwaterasacarrieruid.)
9306C(S)-HM1C, -HM3C, and -HM5C
Pump Dimensions
HM1,3,5
Dim. Inch mm
A 8.56 217.4
B9.33 237.0
C 5.19 131.8
D 3.81 96.8
E 3.88 96.8
HM1 F 11.78 299.2
HM3 F 12.28 311.9
HM5 F 11.90 302.3
HM1,3,5
G 5.03 127.8
H 5.25 133.4
I 2.63 66.8
J 1.91 48.5
9306C(S)-HM1C-3U, -HM3C-3U, and -HM5C-3U
Pump Dimensions
HM1,3,5
Dim. Inch mm
A 8.93 226.8
B9.65 245.1
C 5.51 140.0
D 3.81 96.8
E 3.88 96.8
HM1 F 12.64 321.1
HM3 F 13.14 333.8
HM5 F 12.76 324.1
HM1,3,5
G 5.89 149.6
H 5.25 133.4
I 2.63 66.8
J 1.91 48.5
9306C(S)-HM1C-U, -HM3C-U, and -HM5C-U
Pump Dimensions
HM1,3,5
Dim. Inch mm
A 9.45 240.0
B9.66 245.4
C 5.51 140.0
D 4.33 110.0
E 3.88 96.8
HM1 F 12.64 321.1
HM3 F 13.14 333.8
HM5 F 12.76 324.1
HM1,3,5
G 6.20 157.5
H 5.25 133.4
I 2.63 66.8

L-1546 (Rev E)-7-
Pump Technical Data
9306C-HM1C, 9306S-HM1C, 9306C-HM3C, 9306S-HM3C, 9306C-HM5C, 9306S-HM5C
Pump Specications
Pump
Hydraulic
Max PSI
[BAR]
Max Flow
Rate (GPM)
[LPM]
Max
Pressure
(PSI)
[BAR]
Max Hyd
Flow
(GPM)
[LPM] Ports
Hydraulic
Ports
Dry
Weight
Mounting
Bolts
9306C-HM1C
3000
[206.84]
207 [783.6] 130 [8.9] 13 [49.2]
2" NPT
Inlet
1-1/2"NPT
outlet
1/2" NPT
inlet
3/4" NPT
outlet
33lbs
(15kg)
3/8" OR
M10
9306S-HM1C 214 [810] 135 [9.3] 24 [90.8]
9306C-HM3C 212 [802.5] 140 [9.6] 17 [64.4]
9306S-HM3C 207 [783.6] 130 [8.9] 13 [49.2]
9306C-HM5C 214 [810] 135 [9.3] 24 [90.8]
9306S-HM5C 212 [802.5] 140 [9.6] 17 [64.4]
9306C-HM1C-3U, 9306S-HM1C-3U, 9306C-HM3C-3U, 9306S-HM3C-3U, 9306C-HM5C-3U, 9306S-HM5C-3U
Pump Specications
Pump
Hydraulic
Max PSI
[BAR]
Max Flow
Rate (GPM)
[LPM]
Max
Pressure
(PSI)
[BAR]
Max Hyd
Flow
(GPM)
[LPM] Ports
Hydraulic
Ports
Dry
Weight
Mounting
Bolts
9306C-HM1C-3U
3000
[206.84]
285 [1078.8] 130 [8.9] 13 [49.2]
300 x 220
Universal
Flange
1/2" NPT
inlet
3/4" NPT
outlet
33lbs
(15kg)
3/8" OR
M10
9306S-HM1C-3U 322 [1218.9] 130 [8.9] 24 [90.8]
9306C-HM3C-3U 285 [1078.8] 140 [9.6] 17 [64.4]
9306S-HM3C-3U 285 [1078.8] 130 [8.9] 13 [49.2]
9306C-HM5C-3U 322 [1218.9] 130 [8.9] 24 [90.8]
9306S-HM5C-3U 285 [1078.8] 140 [9.6] 17 [64.4]
9306C-HM1C-U, 9306S-HM1C-U, 9306C-HM3C-U, 9306S-HM3C-U, 9306C-HM5C-U, 9306S-HM5C-U
Pump Specications
Pump
Hydraulic
Max PSI
[BAR]
Max Flow
Rate (GPM)
[LPM]
Max
Pressure
(PSI)
[BAR]
Max Hyd
Flow
(GPM)
[LPM] Ports
Hydraulic
Ports
Dry
Weight
Mounting
Bolts
9306C-HM1C-U
3000
[206.84]
207 [783.6] 130 [8.9] 13 [49.2]
220 X 220
Universal
Flange
1/2" NPT
inlet
3/4" NPT
outlet
33lbs
(15kg)
3/8" OR
M10
9306S-HM1C-U 214 [810] 135 [9.3] 24 [90.8]
9306C-HM3C-U 212 [802.5] 140 [9.6] 17 [64.4]
9306S-HM3C-U 207 [783.6] 130 [8.9] 13 [49.2]
9306C-HM5C-U 214 [810] 135 [9.3] 24 [90.8]
9306S-HM5C-U 212 [802.5] 140 [9.6] 17 [64.4]

L-1546 (Rev E) -8-
Pump Technical Data
Performance Charts
0
1
2
3
4
5
6
7
8
9
10
0 100 200 300 400 500 600 700 800 900
B
A
R
LPM
9306C-HM1C & 9306S-HM1C METRIC
41.6 LPM
45.4 LPM
49.2 LPM
0
20
40
60
80
100
120
140
0 50 100 150 200 250
P
S
I
GPM
9306C-HM1C & 9306S-HM1C
11 GPM
12 GPM
13 GPM
0
1
2
3
4
5
6
7
8
9
10
0 100 200 300 400 500 600 700 800 900
B
A
R
LPM
9306C-HM1C & 9306S-HM1C METRIC
41.6 LPM

45.4 LPM

49.2 LPM
0
20
40
60
80
100
120
140
0 50 100 150 200 250
P
S
I
GPM
9306C-HM1C & 9306S-HM1C
11 GPM
12 GPM
13 GPM
0
20
40
60
80
100
120
140
160
0 50 100 150 200 250
P
S
I
GPM
9306C-HM3C & 9306S-HM3C
18 GPM
20 GPM
22 GPM
24 GPM
0
1
2
3
4
5
6
7
8
9
10
0 100 200 300 400 500 600 700 800 900
B
A
R
LPM
9306C-HM3C & 9306S-HM3C METRIC
68.1 LPM
75.5 LPM
83.3 LPM
90.8 LPM
0
20
40
60
80
100
120
140
160
0 50 100 150 200 250
P
S
I
GPM
9306C-HM5C & 9306S-HM5C
15 GPM
16 GPM
17 GPM
0
1
2
3
4
5
6
7
8
9
10
0 100 200 300 400 500 600 700 800 900
B
A
R
LPM
9306C-HM5C & 9306S-HM5C METRIC
56.8 LPM
60.6 LPM
64.4 LPM
9306C-HM1C-U and 9306S-HM1C-U9306C-HM1C-U and 9306S-HM1C-U9306C-HM1C-U and 9306S-HM1C-U 9306C-HM1C-U and 9306S-HM1C-U
9306C-HM3C-U and 9306S-HM3C-U 9306C-HM3C-U and 9306S-HM3C-U
9306C-HM5C-U and 9306S-HM5C-U 9306C-HM5C-U and 9306S-HM5C-U
9306C-HM5C & 9306S-HM5C METRIC
9306C-HM3C & 9306S-HM3C METRIC
9306C-HM1C & 9306S-HM1C METRIC
9306C-HM5C & 9306S-HM5C
9306C-HM3C & 9306S-HM3C
9306C-HM1C & 9306S-HM1C

L-1546 (Rev E)-9-
Pump Technical Data
Performance Charts
0
20
40
60
80
100
120
0 50 100 150 200 250 300
P
S
I
GPM
9306C-HM1C-3U & 9306S-HM1C-3U
13 GPM
11 GPM
12 GPM
0
1
2
3
4
5
6
7
8
0 200 400 600 800 1000 1200
B
A
R
LPM
9303C-HM1C-3U & 9306S-HM1C-3U METRIC
41.6 LPM
45.4 LPM
49.2 LPM
0
20
40
60
80
100
120
0 50 100 150 200 250 300 350
P
S
I
GPM
9306C-HM3C-3U & 9306S-HM3C-3U
22 GPM
20 GPM
18 GPM
24 GPM
0
1
2
3
4
5
6
7
8
0 200 400 600 800 1000 1200 1400
B
A
R
LPM
9303C-HM3C-3U & 9306S-HM3C-3U METRIC
68.1 LPM
75.7 LPM
83.3 LPM
90.8 LPM
h
0
20
40
60
80
100
120
0 50 100 150 200 250 300 350
P
S
I
GPM
9306C-HM5C-3U & 9306S-HM5C-3U
17 GPM
15 GPM
16 GPM
0
1
2
3
4
5
6
7
8
0 200 400 600 800 1000 1200 1400
B
A
R
LPM
9303C-HM5C-3U & 9306S-HM5C-3U
56.8 LPM
60.6 LPM
64.4 LPM
9306C-HM1C-3U & 9306S-HM1C-3U METRIC
9306C-HM3C-3U & 9306S-HM3C-3U METRIC
9306C-HM5C-3U & 9306S-HM5C-3U METRIC
9306C-HM1C-3U & 9306S-HM1C-3U
9306C-HM3C-3U & 9306S-HM3C-3U
9306C-HM5C-3U & 9306S-HM5C-3U

L-1546 (Rev E) -10-
Fluid Pumping Applications
Application
Pump Materials Compatibility
Impeller Pump Housing Seal
Nylon Polypropylene GTX Stainless Cast Iron Ceramic Silicon Carbide
Weed Control
Chemicals
X X X X X X X
Insect Control X X X X X X X
BrushControl X X X X X X X
Pest Control
Chemicals and
Fumigants
X X X X X X X
Liquid
Fertilizers
X X X X X X
Powdered
Fertilizers
X X X X X X X
Fluid Transfer X X X X X X X
Acids X X X
Table 1
Flammable liquids, sewage, and clean water should never be pumped through a Hypro pump. Hypro pumps are not
designedtobeusedascleanwaterpumpsasdenedin10CFRParts429and431.
Tools
The Hypro centrifugal pumps and mounting assemblies are designed with Imperial (inch) bolts, however, there are many
metric(mm)sizeswhichwillworkwiththesemounts.Inmostcases,anadjustablespannerwrenchcanalsobeused.
Lifting, Transport, and Intermediate Storage
Packaging Descriptions and Unpacking Instructions
• Hypro centrifugal pumps are shipped in cardboard boxes for safe transporting.
• When pumps are shipped in large quantities, they may be put on a pallet to allow for easy storage, lifting and
handling.
• Beforeliftinganypumporpallet,determinetheweightoftheitembylookingattheattachedpackingslipstoestablish
what lifting equipment should be used.
• Beforeinstallingthepump,determineifallthecomponentsarepresentandundamaged.Ifthepumpismissing
components, contact customer service immediately.
• Oncethepumpisunpacked,disposeofthepackaginginamannercompliantwithlocalandnationalregulations.
Lifting Instructions
• BeforeattemptingtoliftaHypropump,ensurethatthesurroundingworkingareaisfreeofhazardswhichcouldcause
injuryordamagetoproperty.
• Duringliftingoperations,anypersonnelnotinvolvedintheliftshouldnotentertheworkingarea.
• Ifliftinghooks,ropeorchainsarebeingusedforalift,theymustbefreeofdamageandberatedtocarry150%ofthe
weight of the load to be lifted.
• Always wear steel-toed shoes and cut-resistant gloves when attempting to lift.
• Whenliftingandcarrying,alwayskeepthepumpclosetoyourbody.(SeeFigure1)
• Whenstartingthelift,bendyourkneesandkeepyourbackstraight.(SeeFigure1)Tighteningthestomachmuscles
willhelpkeepyourbackstraight.
• Duringthelift,useyourlegstodothework.Neveruseyourback,andmakesureyourlegsareatleastshoulder-width
apart. (See Figure 1)

L-1546 (Rev E)-11-
Figure 1
Transport
• All Hypro pumps are capable of being transported by air, sea, rail or motor vehicle. When the pump is shipped, ensure
that the pump is moved in accordance with local and national laws and is properly secured to prevent unwanted
movementwhichcouldcausedamagetopersonorproperty.Priortoshipping,alluidsshouldberemovedfromthe
pump.
Storage
• New pumps in their boxes can be stored several years as long as the port plugs are not removed. Once the plugs
have been removed, if the pump is not to be used for an extended period of time (i.e. more than 30 days), the pump
must be winterized as described in the Cleaning section of this manual.
Assembly and Installation
Assembly
• This pump comes completely assembled.
Installation
BeforeattemptingtoinstallyourHyprocentrifugalpump,itisimperativetoreadandunderstandthefollowing:
• InstallationofaHypropumpshouldonlybeperformedbyatechnicianhavingtheknowledgeandskillsnecessary
toinstallthepumpwithouttheriskofpropertydamageorinjury.
• When handling Hypro pumps, one should wear steel-toed shoes and protective gloves in order to protect the feet
in the event the pump is dropped and protect the hands from any sharp surfaces on the pump or chemicals.
• Pumping systems must be installed in accordance with Hypro installation instructions. Failure to do so will void
yourwarrantyandcouldcausedamagetoproperty,seriouspersonalinjury,ordeath
• Electricalpowercablesandpumphosesmustberoutedwherethereisnoriskofpersonneltripping,walkinginto,
or falling because they have been routed in areas where personnel are expected to move. Electrical power cables and
pump hoses should be routed according to local and national standards.
• Itistheinstaller’sresponsibilitytoensurethatACelectric-drivemotors,Hypropumps,andmetalworkofsupport
structures are bonded to earth (ground), per local and national standards.
• It is the installer’s responsibility to conduct earth continuity tests between AC electric-drive motors, Hypro pumps,
andmetalworkofsupportstructuresandearthaccordingtoEN60204-1:2006/A1:2009,oritssupersedingstandard,to
conrmthatallcomponentsthatneedtobeconnectedtoeartharesatisfactorilybonded.
• Itistheinstaller’sresponsibilitytoconductelectricaltestsinaccordancewithEN60204-1:2006/A1:2009,orits
supersedingstandard,onnishedpumpassemblies.
• All connections to electrical components must be number, symbol, or color-coded generally as recommended by
EN60204-1:2006/A1:2009,oritssupersedingstandard.

L-1546 (Rev E) -12-
• Installers must provide hydraulic components that are capable of withstanding maximum source pressure.
• Theworkingpressuremustbecontrolledbyapressurereliefvalvethatisadjustedtooperateatamaximum
pressure of the hydraulic motor.
• For pumps with gas engines, the exhaust must be directed away from operators and anyone standing nearby to
ensure that exhaust fumes do not enter their breathing zone.
• If a rigid plumbing system is to be used on a Hypro centrifugal pump, the system must be properly aligned with
the inlet and outlet ports.
• Installers must provide hydraulic components that are capable of withstanding maximum source pressure.
• Theworkingpressureinthehydraulicssystemmustbecontrolledbyapressurereliefvalvethatisadjustedto
operateat10%ofthemaximumsystempressure.
• Wheninstalling,adjustingorremovingaHyprocentrifugalpump,ensurethattherearenoobjectswhichcanfall
ontheinstallerandmakecertainthatallmachinerytowhichthepumpistobeattachedisturnedoff.
• Pumps must be installed in a location where they are accessible for any necessary maintenance.
• When a main electrical supply is needed to power electric-drive motors, installers are responsible for ensuring that a
supply disconnect device, capable of isolating the machine from its electricity supply, be provided.
• Whenhydraulicpowerisused,thesystemshouldcontainaquickdisconnectcouplingthatcanbedisconnected
to isolate the pump.
Standard Mounting
• Inordertopreventinjuryordamagetoproperty,allHypropumpsshouldbeproperlymountedtoasolidbasewhere
thereisnodangerofthepumpfallingorbreakingloose.AllHypropumpscomewithmountingholeswhichallow
bolts to be put into the pump so it can be secured to a sturdy base. When mounting your Hypro centrifugal pump, be
sure to use bolts and nuts which are compatible with any chemicals that may come into contact with them as well as
choosing the correct grade of bolt based on the pump weight and any expected loads. Pumps should be mounted
as close to the liquid source as possible. Non self-priming pumps must be mounted below the liquid level to function
properly.
Pump Plumbing
• To achieve maximum pump performance the outlet port on the pump should be pointing staight up, and pump
inlet and outlet lnes should be at least the same size as their respective port. Pump plumbing must be capable of
withstanding the maximum suction, and pressure, generated by the pump and should have as few restrictions as
possible.
• For best priming results, the upper most vent plug can be removed and a vent line can be installed. This line prevents
airlockandallowsthepumptoprimeitselfbybleedingofftrappedair.
Ref.
No. Description
1TankLid
2 Vent Line
3Jet Agitator
4Shut-offBallValves
5 Centrifugal Pump
6 Spray Control Console
7 Centrifugal Pump Control
8ManifoldBoomValve
9 Flowmeter
10 JetTurretNozzleBody

L-1546 (Rev E)-13-
Hydraulic Installation
• Wheninstallingthehydraulicmotorintothetractororsprayer’shydraulicsystem,makesurethatnodirtorliquid
gets into the hydraulic motor.
KEEP ALL HYDRAULIC CONNECTIONS CLEAN.
• Ensure return line is connected to low pressure return port on the tractor recommended for hydraulic motors, the ports
areidentiedonthemotorcasting.Hydraulicsupplylinesshouldbeatleastthesamesizeasthehydraulicmotorport
or larger.
• Standardmodelscomeequippedwithcheckvalveportadapterswhichshouldnotberemoved.
Hooking up the motor in the wrong direction will damage the hydraulic seal.
Control Systems
• All pump systems with electric or hydraulic power sources are required to have a control system which meets all local
and national standards.
• For more detail on a typical system installation, see preceding subsections of the “Assembly and Installation” section
of this manual.

L-1546 (Rev E) -14-
Commissioning, Start-Up, Operation, Shutdown
Beforeattemptingtostartyourpump,thefollowingmustbeunderstoodandfollowedtoensuresafeoperation.
Information
• When running Hypro centrifugal pumps, it is essential that operators use hearing protection as the sound levels
can reach levels of 80 decibels.
• When handling Hypro pumps, one should wear steel-toed shoes and protective gloves in order to protect the feet
in the event the pump is dropped and protect the hands from any sharp surfaces on the pump or chemicals.
• OnlyauthorizedoperatorshavingtheknowledgeandskillnecessarytosafelyuseaHypropump,orany
equipment the pump is connected to, may run the pump.
• Whensprayingmanually,itisrecommendedthatchemical-resistantfacemasksandclothingbeworntoprevent
anychemicalsfromcomingintocontactwiththeskinorbeinginhaled.
• When spraying manually, always spray upwind of yourself as long as the sprayed chemical will not drift into the
vicinity of other people.
• Wheninstalling,adjustingorremovingaHyprocentrifugalpump,ensurethattherearenoobjectswhichcanfall
ontheinstallerandmakecertainthatallmachinerytowhichthepumpistobeattachedisturnedoff.
• Hypro centrifugal pumps should only be used on tractors or tow-behind spray platforms which have electrically
conductivetiresinordertoreducetheriskofelectrocution.
• NeveroperateaHyprocentrifugalpumpoutsidewhilethereisachanceofgettingstruckbylightning.
• Never leave electrical wires or plumbing components where they can be a tripping hazard or become entangled
inamovingcomponent.Ideally,electricalcables,hoses,pipesandttingsshouldberoutedoverhead.Intheevent
electrical wiring must be routed over the ground, operators are required to use rubber ramps if they cross a gangway.
• Hypro centrifugal pumps should not be used if the ambient light is below 200lux.
Only use approved chemicals in your pump. For a complete list of approved chemicals, see the “Fluid
Pumping Applications” section. Failure to follow this warning will void your warranty and could lead to property
damage, serious injury or death.
Start-up, Operation, Shutdown
Before Starting the Pump
• Ensure all unnecessary personnel are clear of the area.
• Forinitialsetupandtestofyoursystem,itisrecommendedtostartwithcleanwaterinsteadofchemicals,andconrm
thesystemandplumbingconnectionsareleakfree.
• Ensurethatthereisuidinthesourcetankorsupplyline.Donotrundry.
• Checklinestrainerfordebrisorclogs.Removeanyfound.
• Checkallplumbingconnectionstomakesuretheyaretight.
• Checkpowersourceandconnections.
• Checkthatallvalvesandregulatorsaresettothedesiredsettingandarefunctioningproperly.
• Ensure all hoses are properly positioned and are not damaged in any way.
• Ensure PTO shaft shields are in place and are not loose.

L-1546 (Rev E)-15-
Priming the Pump
Tohelpprimethepump,keeptheinletorsuctionlineasshortaspossiblewithaminimumofbends,elbowsandkinks.
Makesureallconnectionsaretightanddonotleakair.Nonself-primingpumpsmusthavetheinletlineandpumpooded
withliquidbeforestartingthepump.Forself-primingmodels,thefrontchambershouldbelledwithliquidbeforestarting.
Starting, Operation and Shutdown of the Pump (Hydraulic)
Open Center Systems - All Models
Adjusting Centrifugal Pump Output
ATTENTION HM1C, HM3C & HM5C motors have bypass screw fully closed from the factory. HM2C & HM4C motors have
bypass screw set at 1-1/2 turns from fully closed from the factory.
1. Openthebypassadjustmentscrew2-1/2turnsfromfullyclosedandsecureitinplacewiththebypassjamnut.
2. Start the tractor. Leave the directional valve in the neutral position and allow hydraulic oil to circulate for approximately
10 to 15 minutes or until adequately warmed.
3. Prime the centrifugal pump with all valves open. (See Priming the Pump.)
4. Refertosprayermanufacturer’smanualtosetsprayingpressureandow.Tochangetheoworpressuregenerated
bythepump,turnthebypassscrewonthehydraulicmotor.Besuretosecurethebypassjamnutafterany
adjustment.
5. To shutdown, return directional valve to neutral and allow the pump to come to a gradual stop.
When bypassing hydraulic oil, a large amount of heat can be generated which will damage the tractor’s hydraulic
system.Besuretomonitortheoiltempwhenbypassinghydraulicoil.
Closed Center (Pressure-Compensated) Systems
Adjusting Centrifugal Pump Output
1. Openthebypassadjustingscrewinthehydraulicmotorthree(3)turnsandsecureitinplacewiththebypassjamnut.
2. Start the tractor and allow hydraulic oil to circulate for approximately 10 to 15 minutes or until adequately warmed
3. Closeandlockdownthebypassadjustingscrewinthehydraulicmotor.
4. Prime the centrifugal pump with all valves open. (See Priming the Pump.)
5. Refertosprayermanufacturer’smanualtosetsprayingpressureandow.Tochangetheoworpressuregenerated
bythepump,slowlyadjusttractor’sowcontrolvalve.
6. Toshutdown,thepumpmovetheselectorforthetractorspoolvalvetotheoatpositionandallowthepumptocome
to a gradual stop.
If the pump is not brought to a gradual stop, the sudden change in hydraulic pressure and pump RPM could cause
damage to the pump’s drive system.
Closed Center (Load-Sensing) Systems
Adjusting Centrifugal Pump Output
1. Closeandlockdownthebypassadjustingscrewinthehydraulicmotor.
2. Setthetractorhydraulicowcontrolvalveforminimumhydraulicoilowtotheremoteoutlet(Tortoiseposition).
3. Start the tractor and allow the hydraulic oil to circulate for approximately 10 to 15 minutes or until adequately warmed.
4. Prime the centrifugal pump with all valves open. (See Priming the Pump.)
5. Refertosprayermanufacturer’smanualtosetsprayingpressureandow.Tochangetheoworpressuregenerated
bythepump,slowlyadjusttractor’sowcontrolvalve.
6. Toshutdownthepump,movetheselectorforthetractorspoolvalvetotheoatpositionandallowthepumptocome
to a gradual stop.
If the pump is not brought to a gradual stop, the sudden change in hydraulic pressure and pump RPM could cause
damage to the pump’s drive system.

L-1546 (Rev E) -16-
Maintenance and Servicing
Information
• All maintenance should be done when machinery is stationary and has been isolated from its energy sources.
It is dangerous to perform maintenance while machinery is still connected to its power source. Machinery should be
isolated from its electrical, hydraulic or gas engine power source.
• BesuretoreleaseallpressurefromthesystembeforeperforminganysortofmaintenanceonaHypropump.
• DO NOT perform service or maintenance to the pump, or attached components, until the pump unit is below
109°F(43°C).
• The lubrication of this pump unit has been done at the factory prior to shipping.
• When handling Hypro pumps, one should wear steel-toed shoes and protective gloves in order to protect the feet
in the event the pump is dropped and protect the hands from any sharp surfaces on the pump or chemicals. If the
pump is being repaired while the pump is in service, eye protection should also be worn.
Any hazardous liquids should be disposed of in a manner which complies with local and national regulations. Never dump
uidsontotheground.
Disposal
WhendisposingofaHypropump,besuretoremovealluidsfromthepumpbeforescrapping.Theseuidsshouldbe
disposedofinamannerwhichcomplieswithlocalandnationalregulations.Neverdumpuidsontotheground.Oncethe
pumpisfreeofalluids,itmaybescrappedinaccordancewithlocalandnationallaws.
Cleaning
Yourpumpwilllastlongerandgivebestperformancewhenproperlytakencareof.Properpumpcaredependsonthe
liquidbeingpumpedandwhenthepumpwillbeusedagain.Aftereachuse,ushpumpwithaneutralizingsolutionforthe
liquidjustpumped.Followwithacleanwaterrinse.Thisisespeciallyimportantforcorrosivechemicals.Itisgoodpractice
to clean the pump after each use to prevent deposits from forming and damaging the pump. For infrequent use and before
long periods of storage, drain pump thoroughly. Open any drain plugs, remove suction hose from liquid, and blow pump
drywithair.Anantifreeze/rustinhibitorshouldbeinjectedintothepumpbeforebothportsarepluggedandthepumpis
stored.Plugallportstokeepoutairuntilpumpisusedagain.

L-1546 (Rev E)-17-
Maintenance, Routine Servicing, and Inspection
PREVENTATIVE MAINTENANCE CHECKLIST
Check Daily Weekly
WaterLeaks X
Plumbing X
• Eachsystem’smaintenancecyclewillbeexclusive.Ifsystemperformancedecreases,checkimmediately.
• Dutycycle,temperature,quality,typeofuidbeingpumped,andinletfeedconditionsallaffectthelifeofsprayboom
assemblies and service cycle.
Troubleshooting
Beforeattemptingtoserviceyourpump,besurethatitisdisconnectedfromallenergysources.
Symptom Probable Cause(s) Corrective Action
Pump does not prime Leakinsuctionline Checkhoseandttingsforleaksand
correct
Obstruction in suction line Inspect hose for obstructions and
remove
Suctionhosestucktotank Cut a notch or “V” in end of suction
hose
Clogged strainer Checkstrainerandcleanregularly
Low discharge Pump rotates incorrectly Correct rotation of pump
Blockedsuctionhose Inspect suction hose and repair as
necessary
Pump worn Repair pump
Undersized suction line See Installation
Pump will not turn Impeller plugged Inspect and clear obstruction
Hydraulic system overheating Hydraulicbypassneedsadjustment See Installation
Insufcienthydraulichosesize See Installation
Table 2

L-1546 (Rev E) -18-
Replacement Parts
The following drawings show the pumps and their replacement parts. Only genuine replacement parts should be used.
Failure to follow this warning can result in damage to property, serious injury or death. If the pump malfunctions or
isdefective,itshouldbesentbacktoHyproforservice.
NOTE:Whenorderingparts,
give QUANTITY, PART
NUMBER,DESCRIPTION,and
COMPLETEMODELNUMBER.
Reference number are used
ONLY to identify part in the
drawing and are NOT to be
used as order numbers.
Silicon Carbide Seal Kit No. 3430-0589
Contains:
Mechanical seal (Ref .7) and o-ring (Ref. 5).
Parts Kit No. 3430-0748
Contains:Oneeachball
bearing (Ref. 13), motor
shaft seal (Ref. 16), thread
sealgasket(Ref.35),two
cartridge o-rings (Ref.15),
and washer (Ref 36); two
each motor housing o-rings
(Ref. 22), and port adapter
o-rings (Ref. 30 & 32).
Repair Parts Kit No. 3430-0332
Contains:
One mechanical seal (Ref. 7), one o-ring
(Ref.5)andonerubbergasket(Ref.6).
Hydraulic Motor Part Nos.
2500-0081C (HM1C Models)
2500-0083C (HM3C Models)
2500-0085C (HM5C Models)
Ref.
No. Qty. Req’d. Part No. Description
1 4 2406-0016 Drain/Vent Plug
2 1 0154-9200C1 Pump Casing (9306C)
2 1 0154-9200S1 Pump Casing (9306S)
2A 1 0157-9200C Pump Casing (Universal Flange 220x220)
2B 1 0158-9200C Pump Casing (Universal Flange 300x220 Cast)
2B 1 0158-9200S Pump Casing (Universal Flange 300x220 S.S.)
3 1 2253-0002 Impeller Nut (9306C)
3 1 2253-0006 Impeller Nut (9306S)
4 1 0401-9200P2 Impeller (Nylon Std. 9306C)
4 1 0405-9200P2 Impeller (Polypropylene Optional) (Std. 9306S)
4 1 0407-9306P Impeller (GTX Optional)
5 1 3430-0332 O-ring
6 1 3430-0332 Gasket
7 1 3430-0332 Mechanical Seal (Viton/Cermaic) (Std. 9306C)
7 1 3430-0589 Mechanical Seal (Silicon Carbide) (Std. 9306S)
8 1 0750-9300C2 Mounting Flange (9306C)
8 1 0756-9300S Mounting Flange (9306S)
9 4 2210-0020 Hex Head Cap Screw (9306C)
9 4 2210-0125 Hex Head Cap Screw (9306S)
10 1 1410-0056 Slinger Ring
11 1 1810-0014 Snap Ring
12 1 1820-0013 Retaining Ring
13 1 3430-0748 BallBearing
14 1 1410-0131 Cartridge, Front
15 2 1720-0286 O-ring
16 1 3430-0748 Lip Seal
17 1 1410-0130 Seal Spacer
18 1 2029-0014 ThrustBearingAssembly
19 1 3430-0852 Shaft (HM1C/HM5C)
19 1 3430-0855 Shaft (HM3C)
Ref.
No. Qty. Req’d. Part No. Description
20 1 0150-2500C MotorBody(includesneedlebearing)
21 4 2210-0005 Hex Head Cap Screw
22 2 3430-0748 O-ring
23 1 1600-0044 Dowel Pin (HM1C/HM5C)
23 1 1600-0052 Dowel Pin (HM3C)
24 1 1600-0037 Dowel Pin (HM1C/HM5C)
24 1 1600-0068 Dowel Pin (HM3C)
25 1 3900-0022 Gerotor (HM1C)
25 1 3900-0024 Gerotor (HM3C)
25 1 3900-0048 Gerotor (HM5C)
26 1 0700-2500C1 Gerotor Housing (HM1C Models) 1/2” wide
26 1 0702-2500C1 Gerotor Housing (HM3C Models) 1” wide
26 1 0704-2500C1 Gerotor Housing (HM5C Models) 5/8” wide
27 1 0254-2500C2 Motor End Plate (includes needle bearing)
28 4 2270-0039 Washer
29 4 2220-0021 Cap Screw (HM1C Models)
29 4 2220-0044 Cap Screw (HM3C Models)
29 4 2220-0032 Cap Screw (HM5C Models)
30 1 3430-0748 O-ring
31 1 3360-0021A Pressure Port Adapter (includes o-ring)
32 1 1720-0262 O-ring
33 1 3320-0051A TankPortAdapter(includeso-ring)
34 1 3220-0029 BypassAdjustingScrew
35 1 3430-0748 Gasket
36 1 3430-0748 Washer
37 1 2250-0038 LockNut
38 1 1610-0031 Roll Pin (HM1C/HM5C)
38 1 1610-0055 Roll Pin (HM3C)
39 1 1810-0026 Snap Ring
40 1 1610-0012 Woodruff Key
1
2
4
5
6
8
9
10 11 12 13 14
15
16
17
19
21
20
39
40
38
22
23 24
25
26
27
33
31
29
28
37
36
35
34
18
3
7
30
32
2A
2B
9306C(S)-HM1, 3, 5C and 9306C(S)-HM1, 3, 5C-3U

L-1546 (Rev E)-19-
Rev 12/22/18
EC Declaration of Incorporation
Manufacturers Name: Pentair Flow Technologies, LLC
Manufacturers’ Address: 375 Fifth Avenue NW,
New Brighton, MN 55112, USA
Declare that the partially complete machinery described below conforms to applicable health and safety requirements of Emission Directive
2010/26/EU and of Parts 1 of Annex I of Machinery Directive 2006/42/EC. This partly completed machinery must not be put into service until the
equipment into which it is to be incorporated has been declared in conformity with the provisions of these directives. Condential technical
documentation has been compiled as described in Annex VII Part B of Machinery Directive 2006/42/EC and is available to European national
authorities on written request. If a request is received, documentation will be transmitted either electronically or by post. Clauses 1.1.4, 1.1.7,
1.1.8 Section 1.2, Clauses 1.3.5, 1.3.6, 1.3.7, 1.3.8.1, 1.3.8.2, 1.3.9, 1.4.1, 1.4.2.1, 1.4.2.2, 1.4.2.3, 1.4.3, 1.5.2, 1.5.7, 1.5.12, 1.5.14, 1.5.16, 1.6.2, 1.7.1.1, 1.7.1.2,
1.7.2, and 1.7.4.2 are clauses of Machinery Directive 2006/42/EC that have not been met, but could be applicable and must be addressed during
installation by a third party.
Description: PENTAIR Pump
Type: Roller Pumps
Series Numbers 1502, 1700, 4001, 4101, 6500, 7560, 7700
Type: Centrifugal Pumps
Series Numbers 1442P, 1539, 1540, 1542P, 1543P, 1550, 90XX, 9202, 9203, 9205, 9206,
9208, 9262, 9263, 9253, 9302, 9303, 9305, 9306, 9307, 9308, 9313, 9314,
9316, 9342P, 9343P, 9742P, 15HPS, 93HPS
Type: Cleanload Assembly
Series Numbers 3376, 3378
Type: Piston/Plunger Pumps
Series Numbers 5315C, 5320C, 5321C, 5322C, 5324C, 5325C, 5330C, 53702, 53703
The following standards have either been referred to or been complied with in part or in full as relevant:
ENISO 12100 Machinery Safety - General principles for design - Risk assessment and risk reduction
EN809-1998 + A1 2009 Machinery Safety - Pumps and pump units for liquids - Common safety requirements
EN ISO 13732-1 Machinery Safety - Ergonomics of the thermal environment
EN ISO 3744:2010 Acoustics - Determination of sound power levels and sound energy levels of
noise sources using sound pressure
EN ISO 11202/A1 1997 Machinery Safety - Noise emitted by machinery and equipment
EN 12162:2001+A1:2009 Machinery Safety - Liquid pumps - Safety requirements-Procedure for hydrostatic testing
EN ISO 4254-6:2009 Machinery Safety - Sprayers and liquid fertilizer distributors
EN 60204-1:2006/A1:2009 Machinery Safety - Electrical Equipment of Machines
Name .……………...…………………………………………… Position…..……………………….…..………
Signature …………………………………………..……………. Date…..……..………………………..……….
Place of Signing…………………………………………………………………………………………………….…..
Rev 12/22/18
EC DECLARATION OF INCORPORATION

For a detailed list of where Pentair trademarks are registered, please visit www.pentair.com/en/registrations.html. Pentair trademarks and logos are owned by Pentair PLC. or its aliates.
Third party registered and unregistered trademarks and logos are the property of their respective owners. Because we are continuously improving our products and services, Pentair
reserves the right to change specications without prior notice. Pentair is an equal opportunity employer.
L-1546 Rev. E (12-09-19) ©2019 Pentair. All Rights Reserved.
LIMITED WARRANTY ON HYPRO/SHURFLO AGRICULTURAL PUMPS & ACCESSORIES
AMERICAS & ALL OTHER REGIONS
Hypro / Pentair
Attention: Service Department
375 Fifth Avenue NW
New Brighton, MN 55112
Service: 800-468-3428
Fax: [phone]
Technical: 800-445-8360
hypro.technicalpentair.com
CANADA
Pentair Water Belgium B.V.B.A
Industriepark Wolfstee
Toekomstlaan 30, 2200
Herentals, Belgium
Tel: [phone]
Fax: [phone]
shur[e-mail]
CENTRAL & SOUTH AMERICA
[phone]
[e-mail]
pentair.com
† Carriers, including U.S.P.S., airlines, UPS, ground freight, etc., require specific identification of any hazardous material being shipped. Failure to do so may result in a substantial fine and/or prison term.
Check with your shipping company for specific instructions.
Hypro/Shurflo (hereafter, “Hypro”) agricultural products are warranted to be free of defects in material and workmanship under normal
use for the time periods listed below, with proof of purchase.
- Pumps: one (1) year from the date of manufacture, or one (1) year of use. This limited warranty will not
exceed two (2) years, in any event.
- Accessories: ninety (90) days of use.
This limited warranty will not apply to products that were improperly installed, misapplied, damaged, altered, or incompatible with
fluids or components not manufactured by Hypro. All warranty considerations are governed by Hypro’s written return policy.
Hypro’s obligation under this limited warranty policy is limited to the repair or replacement of the product. All returns will be tested
per Hypro’s factory criteria. Products found not defective (under the terms of this limited warranty) are subject to charges paid by the
returnee for the testing and packaging of “tested good” non-warranty returns.
No credit or labor allowances will be given for products returned as defective. Warranty replacement will be shipped on a freight
allowed basis. Hypro reserves the right to choose the method of transportation.
This limited warranty is in lieu of all other warranties, expressed or implied, and no other person is authorized to give any other
warranty or assume obligation or liability on Hypro’s behalf. Hypro shall not be liable for any labor, damage or other expense, nor shall
Hypro be liable for any indirect, incidental or consequential damages of any kind incurred by the reason of the use or sale of any
defective product.
RETURN PROCEDURES
All products must be flushed of any chemical (ref. OSHA section 1910.1200 (d) (e) (f) (g) (h)) and hazardous chemicals must be labeled/
tagged before being shipped†to Hypro for service or warranty consideration. Hypro reserves the right to request a Material Safety
Data Sheet from the returnee for any pump/product it deems necessary. Hypro reserves the right to “disposition as scrap” products
returned which contain unknown fluids. Hypro reserves the right to charge the returnee for any and all costs incurred for chemical
testing, and proper disposal of components containing unknown fluids. Hypro requests this in order to protect the environment and
personnel from the hazards of handling unknown fluids.
Be prepared to give Hypro full details of the problem, including the model number, date of purchase, and from whom you purchased
your product. Hypro may request additional information, and may require a sketch to illustrate the problem.
Contact the appropriate Hypro Service Department to receive a Return Merchandise Authorization number (RMA#).
Returns are to be shipped with the RMA number clearly marked on the outside of the package. Hypro shall not be liable for freight
damage incurred during shipping. Please package all returns carefully. All products returned for warranty work should be sent shipping
charges prepaid: