Pentair Sta-Rite J Series User manual

MODELS
671T 0294
H.P. MEDIUM HEAD MODELS
1/3 JMBT-56 – JBMBT-56S –
1/2 JMCT-56 JMC3T-56 JBMCT-56S JBMC3T-56S
3/4 JMDT-57 JMD3T-57 – JBMD3T-57S
1 JMET-58 JME3T-58 JBMET-58S JBME3T-58S
1-1/2 JMFT-40 JMF3T-40 JBMFT-40S JBMF3T-40S
2 JMGT-41 JMG3T-41 JBMGT-41S JBMG3T-41S
2-1/2 – – JBMMGT-59S JBMMG3T-59S
H.P. HIGH HEAD MODELS
1/3 JHBT-61H – JBHBT-61S – –
1/2 JHCT-61H JHC3T-61H JBHCT-61S JBHC3T-61S –
3/4 JHDT-62H JHD3T-62H JBHDT-62S JBHD3T-62S JBH2DT-62S
1 JHET-63H JHE3T-63H JBHET-63S JBHE3T-63S –
1-1/2 JHFT-51H JHF3T-51H JBHFT-51S JBHF3T-51S –
2 JHGT-52H JHG3T-52H JBHGT-52S JBHG3T-52S –
2-1/2 – JHHG3T-53H JBHHGT-53S JBHHG3T-53S –
OWNER’S MANUAL
60 CYCLE “J” and “JB” SERIES
CENTRIFUGAL PUMPS WITH TEFC MOTORS
© 2012 Pentair, Ltd. All Rights Reserved. S257 (11/15/12)
293 WRIGHT STREET, DELAVAN, WI 53115 WWW.STA-RITE.COM
PH: 888-782-7483

R
o
t
a
t
i
o
n
Support suction pipe
as required, so that
pump does not take
weight of pipe
Support discharge pipe
as required, so that
pump does not take
weight of pipe
As close
as possible
4 x "D"
minimum
submergence
Foot
Valve
Pipe diameter
"D"
Straight run, as short as
possible but at least 6
times pipe diameter ("D").
Slope pipe down from
pump to water
Short length of
straight pipe
after reducer
Important:
All connections must
be air tight
Solid, level
base
Rotated Volute
Stop
Valve
Union
Discharge
to service
Recommended pump suction
and discharge connections
Vent
Plug
Priming
Plug
Street Elbow
Not recommended pump suction
and discharge connections
Elbow immediately
in front of pump
suction.
On the discharge avoid:
Quick closing valves.
Small I.D. pipe.
Numerous fittings.
Misalignment.
Sharp turns in piping run.
High
lift
Pipe diameter "D"
insufficient size
Pipe submerged
less than 4 x "D"
will cause vortexing
Long suction
run
Concentric
Reducer
Use of excess fittings
means potential air leaks
Valve
Unsupported
Pipe
Concentric Reducer causes high
spots along the suction line resulting
in air pockets.
684 0294 TEFC
Eccentric Reducer,
Straight side up
Tee and
Priming Plug
Figure 1
Figure 2
2

3
California Proposition 65 Warning
This product and related accessories contain
chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
PIPING - GENERAL
Support both suction and discharge piping independently
at a point near the pump to avoid putting a strain on the
pump housing. Start all piping AT THE PUMP.
Increase pipe diameter at both the suction and discharge
by one (1) standard pipe size (minimum) to obtain desired
performance and flow rate. Refer to Table I when sizing
pipe for your pumping system.
NOTICE: Do not use pipe with smaller diameter on the
suction side of pump.
Do not allow pump or any system component to freeze.
To do so will void warranty.
TABLE I
Pump Port Recommended
Size (NPT) Pipe Size
Suction Discharge Suction Discharge
1-1/4 1 1-1/2 1-1/4
1-1/2 1-1/4 2 1-1/2
2 1-1/2 3 2
SUCTION PIPE
Increase pipe size from pump suction port as shown in
Table I.
Figure 1 (Page 2) depicts a recommended run of pipe and
fittings for the suction side of a centrifugal pump. Please
refer to this illustration when choosing pipe and fittings for
your suction connection.
IMPORTANT: All connections must be air tight!
Figure 2 (Page 2) depicts conditions that are NOT
DESIRABLE on the suction side of a centrifugal pump
and may cause problems in flow rate and priming. Please
look this illustration over carefully before choosing pipe
and fittings for your suction connection.
DISCHARGE PIPING
Increase pipe size from pump discharge port as shown in
Table I. Figure 1 (Page 2) depicts a recommended run of
pipe and fittings for the discharge. Install tee with priming
plug as close to pump as possible. Figure 2 (Page 2)
notes conditions that should be avoided. Please read over
carefully before making discharge connection.
PRIMING THE PUMP
A pump is primed when all air in the suction line and
pump volute has been evacuated and replaced with water.
To Prime:
1. Close valve in discharge line.
2. Remove priming plug from tee and fill pump and
suction line with water until water is flowing back out of
tee.
3. Replace priming plug.
4. Start pump and slowly open valve until desired water
flow is achieved.
NOTICE: If water is not being pumped, turn off pump,
close valve, and repeat steps 1 thru 4.
If pump volute is rotated as shown in Figure 1 (Page 2),
loosen vent plug when priming to evacuate air trapped
inside volute. Tighten when volute is completely filled with
water.
Never run pump against closed discharge.
To do so can boil water inside pump causing hazardous
pressure in unit, risk of explosion and possibly scalding
persons handling pump.
NOTICE: Do not run the pump dry. This will damage
mechanical seal and void warranty.
Burn Hazard. Motor normally operates at
high temperature and will be too hot to touch. It is
protected from heat damage during operation by an
automatic internal cutoff switch. Before handling pump or
motor, stop motor and allow it to cool for 20 minutes.

4
Ground motor before
connecting to electrical
power supply.
Failure to ground motor
can cause severe or fatal
electrical shock hazard.
Do not ground to a gas
supply line.
To avoid dangerous or
fatal electrical shock,
turn OFF power to motor
before working on electrical
connections.
Supply voltage must be
within ±10% of
nameplate voltage. Incorrect
voltage can cause fire or seriously damage motor and
voids warranty. If in doubt consult a licensed
electrician.
Use wire size specified in Wiring Chart (below). If
possible, connect pump to a separate branch
circuit with no other appliances on it.
Wire motor according to diagram in motor
junction box.
WIRING
1. Install, ground, wire and maintain this pump in
accordance with electrical code requirements. Consult
your local building inspector for information about
codes.
2. Provide a correctly fused disconnect switch for
protection while working on motor. Consult local or
national electrical codes for switch requirements.
3. Disconnect power before servicing motor or pump.
If the disconnect switch is out of sight of pump,
lock it open and tag it to prevent unexpected power
application.
4. Ground the pump permanently using a wire of the
same size as that specified in wiring chart (below).
Make ground connection to green grounding terminal in
motor junction box marked GRD. or .
5. Connect ground wire to a grounded lead in the service
panel or to a metal underground water pipe or well
casing at least 10 feet long. Do not connect to plastic
pipe or insulated fittings.
6. Protect current carrying and grounding conductors from
cuts, grease, heat, oil, and chemicals.
7. Connect current carrying conductors to terminals in
motor junction box. When replacing motor, check
wiring diagram in motor junction box for correct wiring
connections.
WARNING
Hazardous voltage.
Can shock, burn, or
cause death.
Ground pump before
connecting to power
supply.
TABLE II - RECOMMENDED FUSING AND WIRING DATA - 60 CYCLE MOTORS
*A Fusetron is recommended instead of a fuse in any motor circuit
ELECTRICAL
DISTANCE IN FEET FROM MOTOR TO METER
BRANCH 0’ 101’ 201’ 301’ 401’
MOTOR MAX. LOAD FUSE* TO TO TO TO TO
HP AMPERES RATING VOLT/ 100’ 200’ 300’ 400’ 500’
AMPS PHASE WIRE SIZE
SINGLE PHASE - 115/230 VOLT
1/3 8.2/4.1 15/15 115/230/1 14/14(2/2) 12/14(3/2) 10/14(5.5/2) 8/14(8.4/2) 8/12(8.4/3)
1/2 8.2/4.1 15/15 115/230/1 14/14(2/2) 12/14(3/2) 10/14(5.5/2) 8/14(8.4/2) 8/12(8.4/3)
3/4 11.6/5.8 15/15 115/230/1 14/14(2/2) 10/14(5.5/2) 8/14(8.4/2) 6/14(14/2) 6/12(14/3)
1 14.2/7.1 20/15 115/230/1 12/14(3/2) 8/14(8.4/2) 6/14(14/2) 6/12(14/3) 4/10(21/5.5)
1-1/2 18.0/9.0 25/15 115/230/1 10/14(5.5/2) 8/14(8.4/2) 6/12(14/3) 6/12(14/3) 4/10(21/5.5)
THREE PHASE - 230/460 VOLT
1/2 2.2/1.1 15/15 230/460/3 14/14(2/2) 14/14(2/2) 14/14(2/2) 14/14(2/2) 14/14(2/2)
3/4 2.9/1.45 15/15 230/460/3 14/14(2/2) 14/14(2/2) 14/14(2/2) 14/14(2/2) 14/14(2/2)
1 3.6/1.8 15/15 230/460/3 14/14(2/2) 14/14(2/2) 14/14(2/2) 14/14(2/2) 14/14(2/2)
1-1/2 4.8/2.4 15/15 230/460/3 14/14(2/2) 14/14(2/2) 14/14(2/2) 14/14(2/2) 14/14(2/2)
2 6.0/3.0 15/15 230/460/3 14/14(2/2) 14/14(2/2) 14/14(2/2) 14/14(2/2) 12/14(3/2)
2-1/2 7.0/3.5 15/15 230/460/3 14/14(2/2) 14/14(2/2) 14/14(2/2) 12/14(3/2) 12/14(3/2)
SINGLE PHASE - 230 VOLT
2 10.4 15 230/1 14(2) 14(2) 12(3) 10(5.5) 10(5.5)
2-1/2 11.7 15 230/1 14(2) 14(2) 12(3) 10(5.5) 10(5.5)
SINGLE PHASE - 100-200 VOLT
3/4 12.0/6.0 15/15 100/200/1 14/14(2/2) 10/14(5.5/2) 8/14(8.4/2) 6/14(14/2) 6/12(14/3)

5
8. Motor has automatic internal thermal overload
protection. If motor has stopped for unknown reasons,
thermal overload may restart it unexpectedly, which
could cause injury or property damage. Disconnect
power before servicing motor.
9. If this procedure or the wiring diagrams are confusing,
consult a licensed electrician.
ELECTRICAL
Connect wires to motor according to wiring diagram
below or in motor junction box. Be sure motor is
connected for correct line voltage. If diagram in
motor junction box is different from diagram in this
manual, follow diagram on motor.
For All 3-phase Motors: Follow wiring diagram in
motor junction box or on motor nameplate.
Figure 3 - Motor wiring connections for 100/200V, 115/230V, and 230V only motors
(single phase).
L2
Blue
Black Tracer
Red
Purple
Black
White L1
L2
Blue
Black Tracer
Red
Purple
Black
White L1
Low Voltage
115/230V Dual Voltage 230V Single Voltage
High Voltage
L2
Blue
White L1
3320 0998 WG

6
Seal Plate
Mechanical seal
rotating half
Mechanical seal
stationary half
A-Seal removal-rotating half B-Seal removal-stationary half C-Stationary half installation D-Rotating half installation
T
u
r
n
o
v
e
r
Polished
surface Rubber
surface
Cardboard
washer
(supplied w/seal)
3/4" socket
or pipe
Sealing
face
Rubber drive
ring
Impeller
Shaft
shoulder
5939 0109
FIGURE 4
PUMP SERVICE
This centrifugal pump requires little or no service
other than reasonable care and periodic cleaning.
Occasionally, however, a shaft seal may become
damaged and must be replaced. The procedure as
outlined below will enable you to replace the seal.
NOTICE: These mechanical seals are supplied with
either a rubber seat ring or a sealing O-Ring. They are
completely interchangeable.
NOTICE: The highly polished and lapped faces of
this seal are easily damaged. Read instructions and
handle the seal with care.
Some models are equipped with an impeller screw,
which has a left hand thread. Before unscrewing the
impeller, remove the impeller screw.
REMOVAL OF OLD SEAL
1. After unscrewing impeller (Key No. 5, Page 6),
carefully remove rotating part of seal by prying up
on sealing washer, using two screwdrivers (see
Figure 4A). Use care not to scratch motor shaft.
2. Remove seal plate (Key No. 3) from motor and
place on flat surface, face down. Use a screwdriver
to push ceramic seat out from seal cavity (see
Figure 4B).
INSTALLATION OF FLOATING SEAT
(Figure 4C)
1. Clean polished surface of floating (ceramic) seat
with clean cloth.
2. Turn seal plate over so seal cavity is up; clean
cavity thoroughly.
3. Lubricate outside rubber surface or O-ring of
ceramic seat with soapy water and press firmly
into seal cavity with finger pressure. If seat will not
locate properly in this manner, place cardboard
washer over polished face of seat and press into
seal cavity using a 3/4” socket or 3/4” piece of
standard pipe.
4. Dispose of cardboard washer. Be sure polished
surface of seat is free of dirt and has not been
damaged by insertion. Remove excess soapy
water.
INSTALLATION OF ROTATING PART OF
SEAL UNIT (Figure 4D)
1. Reinstall seal plate using extreme caution not to hit
ceramic portion of seal on motor shaft.
2. Inspect shaft to make sure that it is clean.
3. Clean face of sealing washer with clean cloth.
4. Lubricate inside diameter and outer face of rubber
drive ring (see Figure 4D) with soapy water and
slide assembly on motor shaft (sealing face first)
until rubber drive ring hits shaft shoulder.
5. Screw impeller on shaft until impeller hub hits shaft
shoulder. This will automatically locate seal in place
and move the sealing washer face up against the
facing seat. Reinstall impeller screw (if used).
SERVICE

TROUBLE - CAUSES AND REMEDY
TROUBLE AND CAUSE REMEDY
FAILURE TO PUMP
1. Pump not properly primed. 1. Make sure pump casing and suction line are full of water.
See priming instructions.
REDUCED CAPACITY AND/OR HEAD
1. Air pockets or leaks in suction line. 1. Check suction piping.
2. Clogged impeller. 2. Remove and clean.
PUMP LOSES PRIME
1. Air leaks in suction line. 1. Check suction piping.
2. Excessive suction lift and operating 2. Move pump nearer to water level.
too near shut-off point.
3. Water level drops while pumping, 3. Check water supply. Add length of pipe to suction
uncovering suction piping. to keep submerged end under water.
MECHANICAL TROUBLES AND NOISE
1. Bent shaft and/or damaged bearings. 1. Take motor to authorized motor repair shop.
2. Suction and/or discharge piping not 2. See that all piping is supported to relieve strain
properly supported and anchored. on pump assembly.
7

8
JHGT-52H
Key Part No. JHG3T-52H JHHG3T-53H
No. Description Used 2 HP 2-1/2 HP
1 Motor, 2 HP, 230V, 1 Phase 1 AE100GL-T AE100G5L-T
1 Motor, 2 HP, 230/460V, 3 Phase 1 AP100GL-T AP100G5L-T
†2 Water Slinger 1 17351-0009 17351-0009
3 Seal Plate 1 C3-181 C3-181
†4 Gasket, Seal Plate 1 C20-122 C20-122
†5 Shaft Seal 1 U109-6A U109-6A
6 Impeller 1 C105-214PCA C105-214PA
6A Impeller Screw (3 Phase Only) 1 C30-14SS C30-14SS
7 Volute Assembly with Wear Ring 1 C101-264B C101-264B
7A Wear Ring 1 C23-19 C23-19
8 Pipe Plug, 1/4” NPT Hex Hd. 3 U78-941ZPV U78-941ZPV
9 Base 1 J104-9A J104-9A
9A Motor Pad 1 C35-5 C35-5
10 Socket Head Capscrew, 3/8” - 16 x 1-1/4” Lg 4 U30-104ZP U30-104ZP
2413T 0496
1
2
3
4
5
6
7A
6A
7
10
10
9
9A
8
REPAIR PARTS LIST
“J” SERIES WITH TEFC MOTORS - HIGH HEAD
*For repair or service to motors, always give the motor Model Number and any other data found on the
Motor Model Plate.
SERVICE KIT
Seal and Gasket Kit (J Series) 1 PP1700 PP1700
NOTE: † Included in Seal and Gasket Kit

9
REPAIR PARTS LIST
“J” SERIES WITH TEFC MOTORS - HIGH HEAD
*For repair or service to motors, always give the motor Model Number and any other data found on the Motor Model Plate.
JHBT-61H JHCT-61H JHDT-62H JHET-63H JHFT-51H
Key Part No. – JHC3T-61H JHD3T-62H JHE3T-63H JHF3T-51H
No. Description Used 1/3 HP 1/2 HP 3/4 HP 1 HP 1-1/2 HP
1 Motor, 115V, 1 Phase 1 A100BH-T – – – –
1 Motor, 115/230V, 1 Phase 1 – A100CL-T A100DL-T A100EL-T A100FL-T
1 Motor,, 230/460V, 3 Phase 1 – AP100CL-T AP100DL-T AP100EL-T AP100FL-T
†2 Water Slinger 1 17351-0009 17351-0009 17351-0009 17351-0009 17351-0009
3 Seal Plate 1 C3-1042P C3-1042P C3-1042P C3-1042P C3-1042P
†4 Gasket, Seal Plate 1 C20-121 C20-121 C20-121 C20-121 C20-121
†5 Shaft Seal 1 U109-6A U109-6A U109-6A U109-6A U109-6A
6 Impeller, Single Phase 1 C105-92PN C105-92PN C105-92PM C105-92PL C105-92PB
6 Impeller, Three Phase 1 – C105-92PNA C105-92PMA C105-92PLA C105-92PBA
6A Impeller Screw 1 – C30-14SS C30-14SS C30-14SS C30-14SS
7 Volute Assembly with Wear Ring 1 C101-284A C101-284A C101-284A C101-284A C101-284A
7A Wear Ring 1 C23-27 C23-27 C23-27 C23-27 C23-27
8 Pipe Plug, 1/4” NPT Hex Hd. 1 U78-941ZPV U78-941ZPV U78-941ZPV U78-941ZPV U78-941ZPV
9 Base 1 J104-9A J104-9A J104-9A J104-9A J104-9A
9A Motor Pad 1 C35-5 C35-5 C35-5 C35-5 C35-5
10 Socket Head Capscrew, 3/8” - 16 x 1-1/4” Lg. 4 U30-104ZP U30-104ZP U30-104ZP U30-104ZP U30-104ZP
SERVICE KIT
Seal and Gasket Kit (J Series) 1 PP1700 PP1700 PP1700 PP1700 PP1700
NOTE: † Included in Seal and Gasket Kit

10
2409T 0496 SPC
1
2
3
4
5
6
7A
6A
7
8
10 9
9A
8
8
This drawing is for use with
Models having a capscrew configuration.
10
2410T 0496 SPC
1
2
3
4
5
6
7A
6A
7
8
12
11
12
10
10A
9
This drawing is for use with Models
having a stud configuration.

11
REPAIR PARTS LIST
“J” SERIES WITH TEFC MOTORS - MEDIUM HEAD
*For repair or service to motors, always give the motor Model Number and any other data found on the Motor Model Plate.
JMFT-40 JMGT-41
Key Part No. JMF3T-40 JMG3T-41
No. Description Used 1-1/2 HP 2 HP
1 Motor, 115/230V, 1 Phase 1 A100FL-T AE100GL-T
1 Motor, 230/460V, 3 Phase 1 AP100FL-T AP100GL-T
2 Water Slinger 1 17351-0009 17351-0009
3 Seal Plate 1 C3-52 C3-52
4 Gasket, Seal Plate 1 C20-21 C20-21
5 Shaft Seal 1 U109-6A U109-6A
6 Impeller, Single Phase 1 C105-114PC C105-114PA
6 Impeller, Three Phase 1 C105-114PCA C105-114PA
6A Impeller Screw 1 C30-14SS C30-14SS
7 Volute Assembly with Wear Ring 1 C101-123 C101-123
7A Wear Ring 1 C23-19 C23-19
8 Pipe Plug, 1/4” NPT Sq. Hd. 1 U78-57DT U78-57DT
9 Pipe Plug, 1/4” NPT Hex Hd. 3 U78-941ZPV U78-941ZPV
10 Base 1 J104-9 J104-9
10A Motor Pad 1 C35-5 C35-5
11 Stud, 3/8 - 16 x 1-13/16” 4 U30-35SS U30-35SS
12 Hex Nut, 3/8 - 16 4 U36-38ZP U36-38ZP
*For repair or service to motors, always give the motor Model Number and any other data found on the
Motor Model Plate.
SERVICE KIT
Seal and Gasket Kit (J Series) 1 PP1700 PP1700
NOTE: † Included in Seal and Gasket Kit
JMBT-56 JMCT-56 JMDT-57 JMET-58
Key Part No. – JMC3T-56 JMD3T-57 JME3T-58
No. Description Used 1/3 HP 1/2 HP 3/4 HP 1 HP
1 Motor, 115V, 1 Phase 1 A100BH-T – – –
1 Motor, 115/230V, 1 Phase 1 – A100CL-T A100DL-T A100EL-T
1 Motor, 230/460V, 3 Phase 1 – AP100CL-T AP100DL-T AP100EL-T
2 Water Slinger 1 17351-0009 17351-0009 17351-0009 17351-0009
3 Seal Plate 1 N3-8 N3-8 N3-8 N3-8
4 Gasket, Seal Plate 1 N20-26 N20-26 N20-26 N20-26
5 Shaft Seal 1 U109-6A U109-6A U109-6A U109-6A
6 Impeller, Single Phase 1 J105-42PHA J105-42PHA J105-42PJA J105-42P
6 Impeller, Three Phase 1 – J105-42PHA J105-42PJA J105-42PPA
6A Impeller Screw 1 – C30-6SS C30-6SS C30-6SS
7 Volute Assembly with Wear Ring 1 C101-122E C101-122E C101-122E C101-122
7A Wear Ring 1 N23-7 N23-7 N23-7 N23-7
8 Pipe Plug, 1/4” NPT Hex Hd. 4 U78-941ZPV U78-941ZPV U78-941ZPV U78-941ZPV
9 Base 1 J104-9A J104-9A J104-9A J104-9A
9A Motor Pad 1 C35-5 C35-5 C35-5 C35-5
10 Socket Head Capscrew, 3/8” - 16 x 1-1/4” Lg. 4 U30-104ZP U30-104ZP U30-104ZP U30-104ZP
SERVICE KIT
Seal and Gasket Kit (J Series) 1 PP1700 PP1700 PP1700 PP1700
NOTE: † Included in Seal and Gasket Kit

12
2409T 0496 SPC
1
2
3
4
5
6
7A
6A
7
8
10 9
9A
8
8
This drawing is for use with
Models having a capscrew configuration.
10
2410T 0496 SPC
1
2
3
4
5
6
7A
6A
7
8
12
11
12
10
10A
9
This drawing is for use with Models
having a stud configuration.

13
REPAIR PARTS LIST
“JB” SERIES WITH TEFC MOTORS - MEDIUM HEAD
*For repair or service to motors, always give the motor Model Number and any other data found on the Motor Model Plate.
† Model JBMET-58S uses (2) U30-104ZP and (2) U30-778SS.
*For repair or service to motors, always give the motor Model Number and any other data found on the Motor Model Plate.
JBMBT-56S JBMCT-56S JBMDT-57S JBMET-58S
Key Part No. – JBMC3T-56S JBMD3T-57S JBME3T-58S
No. Description Used 1/3 HP 1/2 HP 3/4 HP 1 HP
1 Motor, 115V, 1 Phase 1 A100BH-T – – –
1 Motor, 115/230V, 1 Phase 1 – A100CL-T A100DL-T A100EL-T
1 Motor, 230/460V, 3 Phase 1 – AP100CL-T AP100DL-T AP100EL-T
2 Water Slinger 1 17351-0009 17351-0009 17351-0009 17351-0009
3 Seal Plate 1 N3-8 N3-8 N3-8 N3-8
4 Gasket, Seal Plate 1 N20-26 N20-26 N20-26 N20-26
5 Shaft Seal 1 U109-6A U109-6A – U109-6A
5 Shaft Seal* 1 – – U109-118 U109-118
6 Impeller, Single Phase 1 J105-42MA J105-42MA – J105-42NA
6 Impeller, Three Phase 1 – C105-42CA J105-42BA J105-42HA
6A Impeller Screw 1 – C30-6SS C30-6SS C30-6SS
7 Volute Assembly with Wear Ring 1 C101-122E C101-122E C101-122E C101-122
7A Wear Ring 1 N23-7 N23-7 N23-7 N23-7
8 Pipe Plug, 1/4” NPT Hex Hd. 4 U78-941ZPV U78-941ZPV U78-941ZPV U78-941ZPV
9 Base 1 J104-9A J104-9A J104-9A J104-9A
9A Motor Pad 1 C35-5 C35-5 C35-5 C35-5
10 Socket Head Capscrew, 3/8” - 16 x 1-1/4” Lg.† 4 U30-104ZP U30-104ZP U30-104ZP U30-104ZP
SERVICE KIT
Seal and Gasket Kit (J Series) 1 PP1700 PP1700 PP1700 PP1700
NOTE: † Included in Seal and Gasket Kit
JBMFT-40S JBMGT-41S JBMMGT-59S
Key Part No. JBMF3T-40S JBMG3T-41S JBMMG3T-59S
No. Description Used 1-1/2 HP 2 HP 2-1/2 HP
1 Motor, 115/230V, 1 Phase 1 A100FL-T – –
1 Motor, 230/460V, 3 Phase 1 AP100FL-T AP100GL-T AP100G5L-T
1 Motor, 230V, 1 Phase 1 – AE100GL-T AE100G5L-T
2 Water Slinger 1 17351-0009 17351-0009 17351-0009
3 Seal Plate 1 C3-52 C3-52 C3-52
4 Gasket, Seal Plate 1 C20-21 C20-21 C20-21
5 Shaft Seal 1 U109-6A U109-6A U109-6A
6 Impeller, Single Phase 1 C105-79B – –
6 Impeller, Three Phase 1 C105-79BA C105-73BA C105-80DA
6A Impeller Screw 1 C30-14SS C30-14SS C30-14SS
7 Volute Assembly with Wear Ring 1 C101-123 C101-123 C101-123B
7A Wear Ring 1 C23-19 C23-19 C23-19
8 Pipe Plug, 1/4” NPT Sq. Hd. 1 U78-57DT U78-57DT U78-57DT
9 Pipe Plug, 1/4” NPT Hex Hd. 3 U78-941ZPV U78-941ZPV U78-941ZPV
10 Base 1 J104-9A J104-9A J104-9A
10A Motor Pad 1 C35-5 C35-5 C35-5
11 Stud, 3/8 - 16 x 2” 4 U30-35SS U30-35SS U30-35SS
12 Hex Nut, 3/8 - 16 4 U36-38ZP U36-38ZP U36-38ZP
SERVICE KIT
Seal and Gasket Kit (J Series) 1 PP1700 PP1700 PP1700
NOTE: † Included in Seal and Gasket Kit

14
2413T 0496
1
2
3
4
5
6
7A
6A
7
10
10
9
9A
8

15
REPAIR PARTS LIST
“JBH” SERIES WITH TEFC MOTORS
*For repair or service to motors, always give the motor Model Number and any other data found on the Motor Model Plate.
*For repair or service to motors, always give the motor Model Number and any other data found on the
Motor Model Plate.
JBHBT-61S JBHCT-61S JBHDT-62S JBHET-63S JBHFT-51S
– JBHC3T-61S JBHD3T-62S JBHE3T-63S JBHF3T-51S
Key Part No. – – JBH2DT-62S – –
No. Description Used 1/3 HP 1/2 HP 3/4 HP 1 HP 1-1/2 HP
1 Motor, 115V, 1 Phase 1 A100BH-T – – – –
1 Motor, 115/230V, 1 Phase 1 – A100CL-T A100DL-T A100EL-T A100FL-T
1 Motor, 100/200V, 1 Phase 1 – – J218-896D – –
1 Motor, 230/460V, 3 Phase 1 – AP100CL-T AP100DL-T AP100EL-T AP100FL-T
†2 Water Slinger 1 17351-0009 17351-0009 17351-0009 17351-0009 17351-0009
3 Seal Plate 1 C3-1042P C3-1042P C3-1042P C3-1042P C3-1042P
†4 Gasket, Seal Plate 1 C20-121 C20-121 C20-121 C20-121 C20-121
†5 Shaft Seal 1 U109-6A U109-6A U109-6A U109-6A U109-6A
6 Impeller, Single Phase 1 C5-256BA C5-256BA C105-94B C5-254BA C5-254BC
6 Impeller, Three Phase 1 – C5-256BA C105-94BA C5-254BA C5-254BC
6A Impeller Screw 1 C30-14SS C30-14SS C30-14SS C30-14SS C30-14SS
7 Volute Assembly with Wear Ring 1 C101-284A C101-284A C101-284A C101-284A C101-284A
7A Wear Ring 1 C23-27 C23-27 C23-27 C23-27 C23-27
8 Pipe Plug, 1/4” NPT Hex Hd. 3 U78-941ZPV U78-941ZPV U78-941ZPV U78-941ZPV U78-941ZPV
9 Base 1 J104-9A J104-9A J104-9A J104-9A J104-9A
9A Motor Pad 1 C35-5 C35-5 C35-5 C35-5 C35-5
10 Socket Head Capscrew, 3/8” - 16 x 1-1/4” Lg. 4 U30-104ZP U30-104ZP U30-104ZP U30-104ZP U30-104ZP
SERVICE KIT
Seal and Gasket Kit (JBH Series) 1 PP1700 PP1700 PP1700 PP1700 PP1700
NOTE: † Included in Seal and Gasket Kit
JBHGT-52S
Key Part No. JBHG3T-52S JBHHGT-53H
No. Description Used 2 HP 2-1/2 HP
1 Motor, 230V, 1 Phase 1 AE100GL-T AE100G5L-T
1 Motor, 230/460V, 3 Phase 1 AP100GL-T AP100G5L-T
†2 Water Slinger 1 17351-0009 C69-2
3 Seal Plate 1 C3-181 C3-181
†4 Gasket, Seal Plate 1 C20-122 C20-122
†5 Shaft Seal 1 U109-6A U109-6A
6 Impeller 1 C5-257BB C5-257B
6A Impeller Screw 1 C30-14SS C30-14SS
7 Volute Assembly with Wear Ring 1 C101-264 C101-264B
7A Wear Ring 1 C23-19 C23-19
8 Pipe Plug, 1/4” NPT Hex Hd. 3 U78-941ZPV U78-941ZPV
9 Base 1 J104-9A J104-9A
9A Motor Pad 1 C35-5 C35-5
10 Capscrew, 3/8 - 16 x 1” Hex Head 2 – U30-74ZP
11 Capscrew, 3/8 - 16 x 1-1/4” Hex Head 2 – U30-75ZP
11 Capscrew, 3/8 - 16 x 1-1/4” Socket Head (1 Phase) 4 U30-104ZP –
11 Capscrew, 3/8 - 16 x 1” Socket Head (3 Phase) 4 U30-99SS –
SERVICE KIT
Seal and Gasket Kit (JBH Series) 1 PP1700 PP1700
NOTE: † Included in Seal and Gasket Kit

16
Limited Warranty
STA-RITE warrants to the original consumer purchaser (“Purchaser” or “You”) of the products listed below, that they will be free from
defects in material and workmanship for the Warranty Period shown below.
Product Warranty Period
Water Systems Products — jet pumps, small centrifugal pumps,
submersible pumps and related accessories
whichever occurs first:
12 months from date of original installation,
or 18 months from date of manufacture
Pro-Source™ Composite Tanks 5 years from date of original installation
Pro-Source™ Steel Pressure Tanks 5 years from date of original installation
Pro-Source™ Epoxy-Lined Tanks 3 years from date of original installation
Sump/Sewage/Effluent Products 12 months from date of original installation, or
18 months from date of manufacture
Our warranty will not apply to any product that, in our sole judgement, has been subject to negligence, misapplication, improper
installation, or improper maintenance. Without limiting the foregoing, operating a three phase motor with single phase power through
a phase converter will void the warranty. Note also that three phase motors must be protected by three-leg, ambient compensated,
extra-quick trip overload relays of the recommended size or the warranty is void.
Your only remedy, and STA-RITE’s only duty, is that STA-RITE repair or replace defective products (at STA-RITE’s choice). You must pay
all labor and shipping charges associated with this warranty and must request warranty service through the installing dealer as soon as
a problem is discovered. No request for service will be accepted if received after the Warranty Period has expired. This warranty is not
transferable.
STA-RITE SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, OR CONTINGENT DAMAGES WHATSOEVER.
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE
FOREGOING WARRANTIES SHALL NOT EXTEND BEYOND THE DURATION EXPRESSLY PROVIDED HEREIN.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on the duration of an
implied warranty, so the above limitations or exclusions may not apply to You. This warranty gives You specific legal rights and You may
also have other rights which vary from state to state.
This Limited Warranty is effective June 1, 2011 and replaces all undated warranties and warranties dated before June 1, 2011.
STA-RITE INDUSTRIES
293 Wright Street • Delavan, WI U.S.A. 53115
Phone: [phone] • Fax: [phone] • Web Site: sta-rite.com