Perel EVM1400 User manual

EVM1400
5 IN 1 MULTIMETER
MULTIMÈTRE 5 IN 1
5-IN-1 MULTIMETER
MULTÍMETRO 5 EN 1
5-IN-1 MULTIMETER
MULTÍMETRO 5 EM 1
USER MANUAL
NOTICE D’EMPLOI
GEBRUIKERSHANDLEIDING
MANUAL DEL USUARIO
BEDIENUNGSANLEITUNG
MANUAL DO UTILIZADOR

EVM1400_v2 PEREL3
EVM1400 – 5 IN 1 MULTIMETER
1. Introduction
To all residents of the European Union
Important environmental information about this product
This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm
the environment.
Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized
company for recycling.
This device should be returned to your distributor or to a local recycling service.
Respect the local environmental rules.
If in doubt, contact your local waste disposal authorities.
Thank you for choosing Velleman! Please read the manual thoroughly before bringing this device into service. If the
device was damaged in transit, don't install or use it and contact your dealer.
2. Safety Instructions
This multimeter has been designed according to IEC-1010 concerning electronic measuring instruments with an
overvoltage category CAT II 1000V, CAT III 600V and pollution 2.
•Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer
will not accept responsibility for any ensuing defects or problems.
•When using this meter, the user must observe all normal safety rules concerning protection against the danger of
electroshocks and protection against misuse.
•The test leads must always be in good condition. Before using, verify that the insulation on the test leads is not
damaged and/or the wires are not exposed.
•Full compliance with safety standards can only be guaranteed if used with the supplied test leads. They must be
replaced with the same model or the same class.
•Never exceed the protection limit values indicated for each measurement range.
•Do not touch unused terminals when the meter is linked to a circuit.
•When the value scale to be measured is unknown, set the range selector at the
highest position.
•Disconnect the test leads form the circuit under test before rotating the range
selector.
•When carrying out measurements on TV or switching power circuits, there may be
high amplitude voltage pulses which may damage the meter.
•Never perform resistance measurements on live circuits.
•Always be careful when handling voltages > 60VDC or > 30VAC RMS. Always
keep fingers behind the guards.
3. Description
1. sound, light and humidity sensors
2. LCD display
3. function switches
4. rotary function/range selector
5. 10A input terminal
6. mA/°C input terminal
7. COM terminal
8. //Hz/V/Ωterminals
To ensure safe operation and in order to exploit the full functionality of the meter, please follow the directions
in this section carefully.

EVM1400_v2 PEREL4
4. Operation
•Data Hold Mode
The data hold function makes the meter stop updating the display. Press HOLD to hold the reading. appears
on the display. Press again to switch off the function.
•Function Selection
Press FUNC. when measuring voltage or current to switch between AC and DC; press the button to select
between resistance, capacitance, diode and continuity measuring.
•Manual Ranging and Autoranging Modes
The meter defaults to the autoranging mode in measurement functions that have mode than one range. The
meter displays when in autoranging mode.
1. Press RANGE to enter the manual ranging mode. Each press on the RANGE key will increase the range.
NOTE: If you manually change the range after entering the data hold mode, the meter will exit this mode.
2. Hold the RANGE key pressed to exit the manual ranging mode and to enter the autoranging mode.
•Hz/Duty Selection
Press Hz/DUTY to switch from the frequency to the duty cycle measurement mode and back.
•Relative Measurement Mode
The meter will display the relative measurement in all functions except for the frequency measurement.
1. Select a function and touch the test leads to the circuit to be measured.
2. Press REL to store the measured value and activate the relative measurement mode. The difference
between the reference value and the subsequent reading is displayed.
3. Press REL for more than 2 seconds to return the meter to normal operation.
•Backlight
Press LIGHT to switch on the backlight. The backlight will automatically fade out after 10 seconds.
•Battery Saver
Turn on the meter. The meter turns off automatically after approximately 15 minutes. Rotate the function selector
or press a button to reactivate the meter.
•DC Voltage
1. Connect the black test lead to the COM jack and the red test lead to the V jack.
2. Set the rotary selector at the desired V range.
3. Press FUNC. to select the AC range.
4. Connect the test leads with the source or the load under measurement.
5. Read the displayed value.
6. The meter indicates an overrange when OL is displayed. Select a higher range. Select the highest range when
the value to be measured is unknown.
To avoid electrical shock and/or damage to the instrument, do not apply more 1,000VDC.

EVM1400_v2 PEREL5
•AC Voltage
1. Connect the black test lead to the COM jack and the red test lead to the V jack.
2. Set the rotary selector at the desired V range.
3. Press FUNC. to select the AC range.
4. Connect the test leads with the source or the load under measurement.
5. Read the displayed value.
6. The meter indicates an overrange when OL is displayed. Select a higher range. Select the highest range when
the value to be measured is unknown.
•DC Current
1. Connect the black test lead to the COM jack and the red test lead to the mA jack for currents of max. 400mA. For
a max. of 10A, connect the red test lead to the 10A jack.
2. Set the rotary selector at the desired A range.
3. Press FUNC. to select the DC range.
4. Connect the test leads in series with the load under measurement.
5. Read the displayed value.
6. The meter indicates an overrange when OL is displayed. Select a higher range. Select the highest range when
the value to be measured is unknown.
•AC Current
1. Connect the black test lead to the COM jack and the red test lead to the mA jack for currents of max. 400mA. For
a max. of 10A, connect the red test lead to the 10A jack.
2. Set the rotary selector at the desired A range.
3. Press FUNC. to select the AC range.
4. Connect the test leads in series with the load under measurement.
5. Read the displayed value.
6. The meter indicates an overrange when OL is displayed. Select a higher range. Select the highest range when
the value to be measured is unknown.
•Resistance Measurement
1. Connect the black test lead to the COM jack and the red test lead to the Ωjack.
2. Set the rotary selector at the desired Ωrange.
3. Press FUNC. to select the Ωrange.
4. Connect the test leads with the resistance.
Note:
•For resistance > 1MΩ, the meter may take a few seconds before stabilizing the reading.
•When the input is not connected, overrange will be displayed as 1.
•The meter indicates an overrange when OL is displayed. Select a higher range.
To avoid electrical shock and/or damage to the instrument, do not apply more 600VAC RMS.
To avoid electrical shock and/or damage to the instrument, never measure a live circuit.
To avoid electrical shock and/or damage to the instrument, never measure a live circuit.
To avoid electrical shock and/or damage to the instrument, disconnect the circuit power and
discharge all high-voltage capacitors before measuring resistance.

EVM1400_v2 PEREL6
•Capacitance Measurement
1. Connect the black test lead to the COM jack and the red test lead to the jack.
2. Set the rotary selector at the desired range.
3. Press FUNC. to select the range.
4. Connect the test leads to the capacitor being measured and read the displayed value.
Note:
•For high capacity values, the meter may take a few seconds before stabilizing the reading.
•For low capacity values, press REL to make the LCD display 000 before measurement.
•Diode Test
1. Connect the black test lead to the COM jack and the red test lead to the jack.
2. Set the rotary selector at the desired range.
3. Press FUNC. to select the range.
4. Connect the red test lead to the anode; connect the black test lead to the cathode of the diode. The
meter will display the approximate forward voltage drop. If the lead connection is reversed, the meter will display
OL.
•Continuity Check
1. Connect the black test lead to the COM jack and the red test lead to the Ωjack.
2. Set the rotary selector at the desired range.
3. Press FUNC. to select the range.
4. Connect the test leads to the resistance in the circuit being measured. If continuity exists, i.e.
resistance < 40Ω, the built-in buzzer will sound.
Note:
•If the measured circuit resistance > 400Ω, the meter will display OL.
•Frequency Measurement
1. Connect the black test lead to the COM jack and the red test lead to the Hz jack.
2. Set the rotary selector at the desired Hz range.
3. Press Hz/DUTY to select the Hz range.
4. Connect the test leads in parallel to the circuit being measured
•Duty Cycle Measurement
1. Connect the black test lead to the COM jack and the red test lead to the Hz jack.
2. Set the rotary selector at the desired Hz range.
3. Press Hz/DUTY to select the duty cycle range.
4. Connect the test leads in parallel to the circuit being measured
To avoid electrical shock and/or damage to the instrument, disconnect the circuit power and
discharge all high-voltage capacitors before measuring capacitance. Use the DC voltage
function to confirm that the capacitor is discharged.
To avoid electrical shock and/or damage to the instrument, disconnect the circuit power and
discharge all high-voltage capacitors before testing diodes.
To avoid electrical shock and/or damage to the instrument, disconnect the circuit power and
discharge all high-voltage capacitors before testing the continuity.

EVM1400_v2 PEREL7
•Temperature Measurement
1. Set the rotary selector at the desired °C range.
2. The LCD will display the current ambient temperature.
3. Connect the black test lead of the “K” type thermocouple to the COM jack and the red test lead to the
°C jack.
4. Touch the object to be measured with the thermocouple.
•Humidity Measurement
1. Set the rotary selector at the desired %RH range.
2. The LCD will display the current ambient humidity.
Note:
•The meter will need a few seconds to stabilize the humidity reading.
•Sound Level Measurement
1. Set the rotary selector at the desired dB range.
2. The LCD will display the current ambient sound level.
•Illuminance Measurement
1. Set the rotary selector at the desired Lux range.
2. Move the meter in front of the light source to be measured.
3. The LCD will display the current illuminance level.
5. Cleaning and Maintenance
Do not attempt to repair or service your multimeter unless you are qualified to do so and have the relevant
calibration, performance test and service information.
a. General Maintenance
Wipe the device regularly with a moist, lint-free cloth. Do not use alcohol or solvents.
Clean the terminals:
•Turn the meter off and remove all test leads.
•Shake out any dirt that may be in the terminals.
•Soak a new cotton bud with a cleaning and oiling agent and clean the terminal.
To avoid electrical shock and/or damage to the instrument, do not connect the thermocouple
to a live circuit.
To avoid electrical shock and/or damage to the instrument, do not connect the input to a live
circuit.
To avoid electrical shock and/or damage to the instrument, do not connect the input to a live
circuit.
To avoid electrical shock and/or damage to the instrument, do not connect the input to a live
circuit.
To avoid electrical shock and/or damage to the instrument, do not get water inside the case.
Remove the test leads and an
y
in
p
ut si
g
nals before o
p
enin
g
the case.

EVM1400_v2 PEREL8
b. Fuse Replacement
•Set the rotary switch to the OFF position.
•Disconnect all test leads and/or any connectors from the terminals.
•Open the battery compartment using an appropriate screwdriver.
•Remove the fuse by sliding it out of its bracket.
•Install a replacement fuse (F 500mA/250V, Ø 5 x 20mm).
•Close the battery compartment.
c. Battery Replacement
•Set the rotary switch to the OFF position.
•Disconnect all test leads and/or any connectors from the terminals.
•Open the battery compartment using an appropriate screwdriver.
•Remove the battery.
•Install a replacement battery (6F22).
•Close the battery compartment.
6. Technical Specifications
Accuracy is specified for one year after calibration at operating temperatures of 18°C ~ 28°C with a relative humidity
at 0% ~ 75%. Accuracy specifications take the form of ± (% of rdg + number of least significant digits).
Environmental Conditions 1000V CAT. II and 600V CAT. III
Pollution Degree 2
Altitude < 2000m
Operating Temperature 0°C~40°C or 32°F~122°F (< 80% RH, < 10°C)
Storage Temperature -10°C~50°C or 14°F~122°F (< 70% RH, battery removed)
Temperature Coefficient 0.1x / C° (< 18°C or > 28°C)
Max. Voltage between Terminals and Earth 600VAC RMS or 600VDC
Fuse Protection F500mA/250V, 5 x 20mm quick fuse
Sample Rate 2x/sec for digital data
Display 35/6 digits LCD with automatic indication of functions and symbols
Over Range Indication yes (“OL”)
Polarity Indication “-“ displayed automatically
Auto Power-Off yes, after 15 min
Continuity Buzzer yes
Transistor Test no
Diode Test yes, 1.0mA (open circuit voltage = 1.5VDC)
Low Battery Indication yes ( )
Max. Display 3,999 counts
Ranging Modes manual or automatic
Data Hold yes
Backlight yes
Power Supply 9V battery
Dimensions 180 x 85 x 45mm
Weight ± 280g (with battery)
Accessories 1 x K-type thermocouple, 2 x test leads, 1 x 9V battery, manual
Before fuse replacement, disconnect all test leads and/or ant connectors from any circuit
under test. To avoid dama
g
e to the instrument
,
re
p
lace the fuse onl
y
with s
p
ecified ratin
g
s.
To avoid false readings, which could lead to possible electric shocks or personal injury,
replace the battery as soon as the battery indicator appears. Before battery replacement,
disconnect all test leads and/or ant connectors from any circuit under test.

EVM1400_v2 PEREL9
DC Voltage
Range Resolution Accuracy
400mV 0.1mV
± (0.7% of rdg + 2 digits)
4V 1mV
40V 10mV
400V 100mV
600V 1V ± (1.0% of rdg + 2 digits)
Overload protection: 250VDC or 250VAC RMS for 400mV range; 600VDC or 600VAC RMS for 4V~600V ranges
Input impedance: 10MΩ
Max. input voltage: 600VDC
Note that the meter may display an unsteady reading when the test leads do not touch the circuit due to the high
sensitivity.
AC Voltage
Range Resolution Accuracy
4V 1mV
± (0.8% of rdg + 3 digits)40V 10mV
400V 100mV
600V 1V ± (1.5% of rdg + 5 digits)
Overload protection: 600VDC or 600VAC RMS for 4V~600V ranges
Input impedance: 10MΩ
Max. input voltage: 600VAC
Frequency range: 40~400Hz
Response: avg, calibrated in RMS of the sine wave
Note that the meter may display an unsteady reading when the test leads do not touch the circuit due to the high
sensitivity.
DC Current
Range Resolution Accuracy
40mA 10µA ± (1.2% of rdg + 3 digits)
400mA 100µA ± (1.2% of rdg + 3 digits)
10A 10mA ± (2.0% of rdg + 10 digits)
Overload protection: F500mA/250V quick fuse for mA ranges; unfused for 10A range
Max. input current: 400mA for mA terminal; 10A for 10A terminal
Voltage drop: 5mV/1mA for mA ranges; 10mV/1A for 10A range
AC Current
Range Resolution Accuracy
40mA 10µA ± (1.5% of rdg + 5 digits)
400mA 100µA ± (1.5% of rdg + 5 digits)
10A 10mA ± (3.0% of rdg + 10 digits)
Overload protection: F500mA/250V quick fuse for mA ranges; unfused for 10A range
Max. input current: 400mA for mA terminal; 10A for 10A terminal
Voltage drop: 5mV/1mA for mA ranges; 10mV/1A for 10A range
Frequency range: 40~400Hz
Response: avg, calibrated in RMS of the sine wave

EVM1400_v2 PEREL10
Resistance
Range Resolution Accuracy
400Ω0.1Ω
± (1.2% of rdg + 2 digits)
4kΩ1Ω
40kΩ10Ω
400kΩ100Ω
4MΩ1kΩ
40MΩ10kΩ± (2.0% of rdg + 5 digits)
Open circuit voltage: 0.25V
Overload protection: 250VDC or 250VAC RMS
Capacitance
Range Precision Accuracy
4nF 1pF
± (3.0% of rdg + 3 digits)
40nF 10pF
400nF 0.1nF
4µF 1nF
40µF 10nF
200µF 100nF ± (8.0% of rdg + 10 digits)
Overload protection: 250VDC or 250VAC RMS
Frequency
Range Resolution Accuracy
9.999Hz 0.001Hz ± (2.0% of rdg + 5 digits)
99.99Hz 0.01Hz
± (1.5% of rdg + 5 digits)999.9Hz 0.1Hz
9.999kHz 1Hz
99.99kHz 10Hz
± (2.0% of rdg + 5 digits)
199.9kHz 100Hz
> 200kHz as reference
Hz range
Measurement range: 0~200kHz
Input voltage range: 0.5VAC – 10VAC RMS
Overload protection: 250VDC or 250VAC RMS
V range
Measurement range: 0~40kHz
Input voltage range: 0.5VAC – 600VAC RMS
Input impedance: 10MΩ
Max. input voltage: 600VDC or 600VAC RMS
mA range
Measurement range: 0~40kHz
Max. input current: 400mA DC or AC RMS
Overload protection: F500mA/250V quick fuse