Performance Travel Trac 2000 User manual

Thank you for purchasing the Performance Travel Trac 2000™ portable trainer.
The Travel Trac 2000™ was designed to provide maximum stability and ease of
use in a convenient, portable folding trainer.
This trainer offers many notable features which make it a good choice for your
training needs:
• Extremely stable and rigid design.
• Easy setup and bicycle installation.
• Spring loaded resistance positioning system to prevent
excessive tire wear.
• Quickly folds flat for storage and easy portability.
• Choice of resistance units available separately.
(A resistance unit is required for operation.)
Travel and Storage:
1. Release the spring plate lock by pushing down on the spring plate with the palm
of your hand, and then pulling up on the spring plate release lever with your
fingers. Allow the spring plate to slowly rotate all the way up (Fig. 1). To prevent
a pinching hazard, never store the Travel Trac 2000™ with the spring plate locked
down.
2. Coil any resistance unit cables and hang over handle.
3. Grasp the Travel Trac 2000™ by the handle and lift. The legs should then fold,
and the trainer is ready for transport or storage. Be careful to avoid pinching
when the legs fold.
CAUTION:
1. This trainer is intended for single-rider bicycles only.
2. Check for proper and secure installation of the bicycle before beginning
each workout.
3. Make sure that resistance unit cables are clear of all moving bicycle parts.
4. Do not leave trainer unattended with spring plate mechanism in locked
(down) position. This could present a potential pinching hazard to
children.
Bicycle Removal:
1. Push the spring plate down as far as possible towards the floor to
automatically engage the spring plate lock. The spring plate must be
locked down to remove the bicycle (Fig. 6).
2. Slide the Travel Trac 2000™’s locking ring ( Fig. 3A) to the right
(away from the bike).
3. While supporting the bicycle, loosen the right side axle support with the
handle, until bicycle is free of the support cups.
Folding Bicycle Trainer
Assembly:
1. Remove from the box and identify all parts for assembly. If you believe
parts are missing, please contact our technical service department for
assistance at 1-800-727-2453 from 9 am to 6pm EST.
2. Assemble feet to legs as shown. (Fig. 1)
3. Assemble handle to axle support with a light tap as shown. (Fig. 1)
Performance Tech Support 1(800)727-2453
9am-6pm EST Monday-Friday
®
™
Performance, Inc.
One Performance Way
Chapel Hill, N.C. 27514
Made in Italy
www.performancebike.com

Bicycle Installation:
1. Set the Performance Travel Trac 2000™ on
a flat, stable surface.
2. Make sure that the bicycle’s rear wheel
skewer is tight.
3. Slide the locking ring to the right (Fig. 3A) and fully unscrew the axle support
mechanism.
4. Push the spring plate down as far as possible towards the floor to automatically
engage the spring plate lock. The spring plate must be locked down to install the
bicycle (Fig. 6).
LEFT
RIGHT
Parts Included:
Lock
Release
NO. DESCRIPTION QTY
1 Travel Trac 2000 Frame 1
2 Handle 1
3 Plastic Feet 4
4 M5 bolt 2
Fig. 1
Fig. 2
Fig. 4
Fig. 5
Fig. 7
Fig. 6
11. If the bike is not stable, make sure that
the QR lever is positioned correctly in
the support cups, and the axle support
mechanism is tightened securely.
12. Release the spring plate lock by pushing
down on the spring plate with the palm
of your hand, and then pulling up on
the spring plate release lever with your
fingers. Allow the spring plate to slowly
rotate upwards until the resistance
unit’s roller makes contact with the rear
wheel of the bicycle (Fig. 7). Now you’re
ready to roll!
Resistance unit
not shown for clarity.
Pull Up
Push
Down
1
2
Axle Support Cups
4. Install the resistance Unit to the spring
plate as shown (Fig. 2). See instructions
included with your resistance unit.
Tighten securely.
5. Carefully lift your bike into position,
aligning the rear wheel axle with the
axle support cups (Fig’s 4 & 5).
6. While holding the bicycle steady, slide
the left side of the quick release skewer
into the axle support cup. Make sure
that the QR lever aligns with the notch
in the support cup. Rotate the support
cup as necessary.
NOTE: If your QR Lever will not fit into the
support cup notches, replace the QR
Lever with a smaller one.
7. Using the handle, tighten the right side
axle support until the support cup
comes in contact with the bicycle’s
right side QR skewer nut. After contact is
made, tighten by turning the handle 1/2
rotation.
8. Slide the locking ring (Fig 3B) fully to
the left (toward the bike) to lock the
axle support mechanism.
9. If the wheel is not centered on the
resistance unit, loosen the M5 socket
head screws on the resistance unit and
slide it sideways as necessary. Retighten
the screws.
10. Test that the bike is secure by pushing
and pulling on the top tube or seat.
Fig. 3
Rotate
Up
3
1
3
2
4
A. Unlocked
B.Locked
Locking Ring

Bicycle Installation:
1. Set the Performance Travel Trac 2000™ on
a flat, stable surface.
2. Make sure that the bicycle’s rear wheel
skewer is tight.
3. Slide the locking ring to the right (Fig. 3A) and fully unscrew the axle support
mechanism.
4. Push the spring plate down as far as possible towards the floor to automatically
engage the spring plate lock. The spring plate must be locked down to install the
bicycle (Fig. 6).
LEFT
RIGHT
Parts Included:
Lock
Release
NO. DESCRIPTION QTY
1 Travel Trac 2000 Frame 1
2 Handle 1
3 Plastic Feet 4
4 M5 bolt 2
Fig. 1
Fig. 2
Fig. 4
Fig. 5
Fig. 7
Fig. 6
11. If the bike is not stable, make sure that
the QR lever is positioned correctly in
the support cups, and the axle support
mechanism is tightened securely.
12. Release the spring plate lock by pushing
down on the spring plate with the palm
of your hand, and then pulling up on
the spring plate release lever with your
fingers. Allow the spring plate to slowly
rotate upwards until the resistance
unit’s roller makes contact with the rear
wheel of the bicycle (Fig. 7). Now you’re
ready to roll!
Resistance unit
not shown for clarity.
Pull Up
Push
Down
1
2
Axle Support Cups
4. Install the resistance Unit to the spring
plate as shown (Fig. 2). See instructions
included with your resistance unit.
Tighten securely.
5. Carefully lift your bike into position,
aligning the rear wheel axle with the
axle support cups (Fig’s 4 & 5).
6. While holding the bicycle steady, slide
the left side of the quick release skewer
into the axle support cup. Make sure
that the QR lever aligns with the notch
in the support cup. Rotate the support
cup as necessary.
NOTE: If your QR Lever will not fit into the
support cup notches, replace the QR
Lever with a smaller one.
7. Using the handle, tighten the right side
axle support until the support cup
comes in contact with the bicycle’s
right side QR skewer nut. After contact is
made, tighten by turning the handle 1/2
rotation.
8. Slide the locking ring (Fig 3B) fully to
the left (toward the bike) to lock the
axle support mechanism.
9. If the wheel is not centered on the
resistance unit, loosen the M5 socket
head screws on the resistance unit and
slide it sideways as necessary. Retighten
the screws.
10. Test that the bike is secure by pushing
and pulling on the top tube or seat.
Fig. 3
Rotate
Up
3
1
3
2
4
A. Unlocked
B.Locked
Locking Ring

Thank you for purchasing the Performance Travel Trac 2000™ portable trainer.
The Travel Trac 2000™ was designed to provide maximum stability and ease of
use in a convenient, portable folding trainer.
This trainer offers many notable features which make it a good choice for your
training needs:
• Extremely stable and rigid design.
• Easy setup and bicycle installation.
• Spring loaded resistance positioning system to prevent
excessive tire wear.
• Quickly folds flat for storage and easy portability.
• Choice of resistance units available separately.
(A resistance unit is required for operation.)
Travel and Storage:
1. Release the spring plate lock by pushing down on the spring plate with the palm
of your hand, and then pulling up on the spring plate release lever with your
fingers. Allow the spring plate to slowly rotate all the way up (Fig. 1). To prevent
a pinching hazard, never store the Travel Trac 2000™ with the spring plate locked
down.
2. Coil any resistance unit cables and hang over handle.
3. Grasp the Travel Trac 2000™ by the handle and lift. The legs should then fold,
and the trainer is ready for transport or storage. Be careful to avoid pinching
when the legs fold.
CAUTION:
1. This trainer is intended for single-rider bicycles only.
2. Check for proper and secure installation of the bicycle before beginning
each workout.
3. Make sure that resistance unit cables are clear of all moving bicycle parts.
4. Do not leave trainer unattended with spring plate mechanism in locked
(down) position. This could present a potential pinching hazard to
children.
Bicycle Removal:
1. Push the spring plate down as far as possible towards the floor to
automatically engage the spring plate lock. The spring plate must be
locked down to remove the bicycle (Fig. 6).
2. Slide the Travel Trac 2000™’s locking ring ( Fig. 3A) to the right
(away from the bike).
3. While supporting the bicycle, loosen the right side axle support with the
handle, until bicycle is free of the support cups.
Folding Bicycle Trainer
Assembly:
1. Remove from the box and identify all parts for assembly. If you believe
parts are missing, please contact our technical service department for
assistance at 1-800-727-2453 from 9 am to 6pm EST.
2. Assemble feet to legs as shown. (Fig. 1)
3. Assemble handle to axle support with a light tap as shown. (Fig. 1)
Performance Tech Support 1(800)727-2453
9am-6pm EST Monday-Friday
®
™
Performance, Inc.
One Performance Way
Chapel Hill, N.C. 27514
Made in Italy
www.performancebike.com