Perlegear PGMTK1 User manual

Wall Plates Left TV
Bracket
Right TV
Bracket
MEDIUM TILT
TV WALL MOUNT
For 23”-55”
(58-140 cm)
TVs
Model PGMTK1
Select TV Screw Diameter Select TV Screw Length
FLAT BACK ROUND BACK CABLESINSET HOLES
AB
Too Short
Too Long
Correct
Stud
Finder Awl or Thin Nail Pencil Level
Drill
SocketWood Drill
Tools:
01 x1 02 x1 03 x1
Position your TV
bracket configuration
(Aor B)over your TV
hole pattern - making
sure the bracket is
centered over the
TV hole pattern and
level. Secure bracket
using your screw/
washer (A-Flat Back)
or spacer/screw/
washer (B-Round
Back / Extra Space)
selection.
CAUTION:
Ensure TV bracket
is securely fastened
before moving on to
the next step.
Rev.02
Attach the TV Bracket
If your TV has a flat back AND you want your TV closer to
the wall, use the shorter screws (A).
Use the spacers and longer screws (B) to accommodate:
•Round/irregular back TVs
•TVs with inset mounting holes
•Extra space needed for cables
CAUTION:
Verify adequate thread
engagment with the screw or
screw/spacercombination.
-Too short will not hold the TV.
-Too long will damage the TV.
Hand thread screws into the threaded inserts
on the back of your TV to determine which
screw diameter (M4, M5, M6, or M8) to use.
66 lbs.
(30 kg)
Does your TV weight more
than 66 lbs. (30 kg) including
accessories?
No
— Perfect!
Yes
— This mount is NOT compatible.
WARNING: Exceeding the weight
capacity can result in serious personal injury
or damage to equipment! It is the installer's
responsibility to make sure the weight of the
TV (with accessories) does not exceed 66 lbs
(30 kg).
A
B
WARNING:This
product contains small
items that could be
a choking hazard if
swallowed.
Before starting
assembly, verify all
parts are included and
undamaged. If any parts
are missing or damaged,
do not return the
damaged item to your
dealer; contact Customer
Service. Never use
damaged parts!
Drywall with
wood studs?
Perfect!
?
What is your wall made of? Please read through these instructions completely to be sure you’re comfortable with
this easy install process. Also check your TV owner’s manual to see if there are any
special requirements for mounting your TV.
If you do not understand these instructions or have doubts about the safety of the
installation, assembly or use of this product, contact Customer Service at
[email protected]
CAUTION: Avoid potential personal injuries and property damage!
●This product is designed for useinwoodstud walls - DONOT install into drywall alone
●The wall must be capable of supporting five times the weight of theTVand mount combined
●Do not use this product for any purpose not explicitly specified by manufacturer
●Manufactureris not responsible for damage or injury caused by incorrect assembly oruse
Standard configurations
are shown. For special
applications, or if you
are uncertain about your
hardware selection,
contact Customer Service
at customerservice@perl
egear.com
Contact Customer Service:
[email protected]
Screw
driver
1/2 in.
(12.7 mm)
7/32 in.
(5.5 mm)
Lag Bolts
x4
Philips Screws
M6 x 15mm
M6 x 30mm
Philips Screws
M4 x 12mm
M4 x 30mm
Philips Screws
M5 x 12mm
M5 x 30mm
Washers
Ø6mm
M4-5-6
Spacers
L10mm
x4
x4 x4 x4 x4x4
Philips Screws
M8 x 15mm
M8 x 30mm
x4
x4 x4 x4
M-G M-H M-I M-J
Spacers
L5mm
x8
M-K
Allen
Wrench
x1
CA
Washers
Ø8mm
x4
B
M-J
M-E M-G
M-CM-A
M-J
M-K
M-I
M-F M-H
M-DM-B
Hardware (Wall / Procduct) TV Screws / Washers
5/16 x 2½ in
M6M4 M5 M8
STEP 1-1 STEP 1-2 STEP 1-3
(included
inside the box)
02
03
03
02

16 - 24 in.
16 in.
(406 mm)
2-1 2-2
2-4 01
01
01
02
03
Adjust the tilting angle with the Allen wrench for both and .
Locate your
stud. Verify
and mark
the center
of the stud
by finding the
stud edges using
an awl, a thin
nail, or an edge-
to-edge stud finder.
Position
the wall
plate at your
desired
height and line
up the holes with
your stud center
line. Level the wall plate
and mark the holes.
01
Install the
wall plate
assembly using lag
bolts and
washer .
A
B
B
Tighten
the lagbolts
A
only until it against the
wall plate.
STEP 3 Tighten Nuts
STEP 4 Hang TV
STEP 5 Secure TV
Pull the strap down and push the
TV to secure the TV brackets
and to the wall plate
CAUTION: Avoid potential personal injuries and property damage!
●Drywall covering the wall must not exceed 5/8 in. (16 mm)
●Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)
CAUTION: Avoid potential personal injury or property damage! All lag bolts AMUST BE firmly tightened to prevent
unwanted movement of the wall plate assembly.
CAUTION: Ensure the wall plate assembly is securely fastened to the wall before continuing on to the next step.
02
03
C
C
C
Perle electronics hardware (Hongkong) Co., Limited (collectively, “Perle electronics hardware”), intend to make this manual accurate and complete. However, Perle electronics hardware makes no claim that the informations contained harein covers all details, conditions, or variations.
Nor does it provide for every possible contingency in connection with the installation or use of this product.
The information contained in this document is subject to change without notice or obligation of any kind.
Perle electronics hardware makes no representation of warranty, expressed or implied, regarding the information contained harein . perle electronics hardware assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
c 2016 Perle electronics hardware. All right reserved.
Perlegear is a Perle electronics hardware brand. Perlegear and the Perlegear logo are trademarks of Perle electronics hardware.
Made in China.
Perle electronics hardware Clobal Headquarters • Room 1505 Building 17/F NO.3，Kwai Cheong Rd Nt，HongKong •
Any questions please contact : [email protected]
2-3
Drill pilot holes using a 7/32 in. (5.5 mm) diameter drill bit.
IMPORTANT: Be sure to drill into the center of the stud.
IMPORTANT: Pilot holes must be drilled to a depth of in.
(70mm).
7/32 in.
(5.5 mm)
in. (70 mm)
STEP 2 Wood Stud
A
02
02
03
0302
Tighten
Ajust this nut
Loosen
03