Perlesmith PSSM01 User manual

Installation Instructions V1.0
PSSM01
Thank you for choosing our product! We strive to provide the best quality
and services for our customers. Would you kindly share your experience
on Amazon if you are satisfied? Should you have any issues, please don't
hesitate to contact us.
Telephone：[phone] Mon-Fri 10am - 6pm (PST) (USA) (CAN)
Email：[email protected] (US/CA/DE/UK/FR/IT/ES/JP/AU)

Wall Plate
01
02
x1
x1
Supplied Parts
Tools Needed (Not lncluded)
Stud Finder Tape measure Pencil Drill
4 mm
Wood Drill
10 mm
Concrete Drill Screw Driver
Hammer
IMPORTANT SAFETY INFORMATION
•Check package contents against Supplied Parts and Hardware List to assure that all
components were received undamaged. Do not use damaged or defective parts.lf you
require replacement parts, contact customer service at [email protected]
•Not all parts and hardware included will be used.
•Carefully read all instructions before attempting installation.If you do not understand
the instructions or have any concerns or questions, please contact customer service at
[email protected]
•This product may contain moving parts. Use with caution.
•Do not use this product for any purpose or in any configuration not explicitly specified
in this instruction. We hereby disclaim any liability for injury or damage arising from
incorrect assembly, incorrect mounting, or incorrect use of this product.
•DO NOT INSTALL INTO DRYWALL ALONE.
•Please check www.perlesmith.com for more products and company information.
1

Hardware for Attaching the Arm Assembly/Wall Plate to Wall
These anchors are for
concrete or brickwalls
ONLY. DO NOT use them
in drywall or wood studs.
CAUTION!
x2
A2
Wall
Anchor
Lag Bolts
ST6.3*50
x2
x1 x1
A1
B1 B2
WARNING:
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum 1½ x 3½
in. (38 x 89 mm)
● Stud center must be verified
Step 1
For wood stud installation, follow STEP 1A
For concrete installation, follow STEP 1B
Attach the Wall Plate [01] to Wall
Step 1A Wood Stud Option
X
●Avoid potential personal injury or property damage!
● DONOT USE THE WALL ANCHORS [A2] FOR THIS STEP.

Drill 2 pilot holes using a 4 mm
diameter drill bit. Make sure the
depth is not less than 50mm
Use a stud finder(not included)to
locate wood studs. Mark the edge
and center locations.
Position the wall plate[01] at your
desired height and line up the
holes with your stud center line.
Level the wall plate and mark the
holes.
Screw the lag bolts [A1] into
the pilot holes using wrench
[02] until 4mm of the bolts are
left.
1A-1
1A-2
1A-3
50mm
4mm
4mm
A1
02

WARNING:
●Avoid potential personal injury or property damage!
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Minimum solid concrete thickness: 203 mm (8 in.)
● Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)
Step 1B Solid Concrete or Concrete Block Option
Wall
Anchor
A2
Position the wall plate[01] at your desired
height, level the wall plate and mark the pilot
hole locations.
Drill 2 pilot holes using a 10mm diameter
drill bit. Make sure the depth is not less
than 55mm. Never drill into the mortar
between blocks.
1B-1
1B-2
55mm
10mm

Step 2 Secure the Wall Plate [01] to Your Sonos PLAY: 1 Speaker
1B-3
B1 B2
A1
A2
Screw the lag bolts [A1] into
the pilot holes using wrench
[02] until 4mm of the bolts are
left.
4mm
02

Step 3 Hang your Speaker onto the Lag Bolt

Step 4
The speakers can be swivelled
and tilted using wrench [02] if needed
Tilt
Adjustment
02