Perlesmith PSTVS09 User manual

Thank you for choosing our product! We strive to provide the best quality
and services for our customers. Would you kindly share your experience
on Amazon if you are satisfied? Should you have any issues, please don't
hesitate to contact us.
Telephone：[phone] Mon-Fri 10am - 6pm (PST) (USA) (CAN)
Email：[email protected] (US/CA/DE/UK/FR/IT/ES/JP/AU)
PSTVS09
V4.0

Support
Pillar
Foot pads
Plastic cover
•Carefully open the carton, remove contents and lay out on cardbard or other protective
surface to avoid damage.
•Check to assure that all components were received undamaged. Do not use damaged or
defective parts.lf you require replacement parts, contact customer service at
[email protected]
•Carefully read all instructions before attempting installation.
UNPACKING INSTRUCTIONS
IMPORTANT SAFETY INFORMATION
•Install and operate this product with care. Please read this instruction before beginning the
installation, and carefully follow all instructions contained herein. Use proper tools during
installation.
•Do not use this product for any purpose or in any configuration not explicitly specified in
this instruction. We hereby disclaim any liability for injury or damage arising from incorrect
assembly, incorrect mounting, or incorrect use of this product.
Step 1 Connecting the Support Pillar(P) to Tempered Glass(O)
M6x25 Bolt
Tempered
Glass
Gasket
Place foot pads(W) on the bottom of the
tempered glass base(O) at the corners
1.1
(V)
• If you do not understand the instructions or have any concerns or questions, please contact
customer service at
[email protected] or call a qualified installation contractor.
Wrench

2
1.2
1.3
Put tempered glass(O) on the table. Put Gasket(R) and M6x25
Bolt(L) under tempered glass(O).Make sure the paperside of the
gasket(R) face to the tempered glass(O). Turn Plastic Cover(Y)
and Support Pillar(P) upside down under tempered glass(O) and
then tighten the bolts(L) with the wrench(V).
If you find the support pillar(P) is not in the correct direction, please see figure 1.3
below. Loosen M6x25 bolts (L), adjust the support pillar(P) to the correct direction,
then tighten bolts (L) again.
Connecting the TV Plate(M) to Support Pillar(P)
Step 2
TV Plate
(S)M6x40 Bolt
(T)D6 Washer
(V)Wrench
two choices
for height
adjustment
Connecting TV plate(M) to support pillar(P)
by using M6x40 bolts(S) and supporting
with D6 washer(T), please see above
figures.

Attaching wire clips(J)
(J)Wire Clip
Step 3 Measure VESA and Check TV screws
Measure the distance between the holes located at the back of
your TV (these measures may form the shape of a square, or a
rectangle) and check that these taken measures are within the
VESA (*) range for this wall mount. (*) VESA: International
standard established by the TV manufacturers used to
determine if LCD/LED TVs are compatible with wall mounts.
Check TV screws
Hand thread screws into the threaded inserts
on the back of your TV to determine which
screw diameter (M4, M6, or M8) to use.

8
8
F
A C E
B D
F
Step 4
When attaching brackets to the flat screen, be careful not to over tighten
screws and be sure that screws do not bottom out in the mounting holes.
Too Short Too Long
Correct Correct
Mounting the Monitor Bracket(N) to a TV
(N)Monitor Bracket
(A)M4x30 Bolt
(B)M6x16 bolt
(C)M6x30 bolt
(D)M8x16 bolt
(E)M8x45 bolt
(G) M8.5x18x5
Spacer
(H) M8.5x18x10
Spacer
(F)Washer
FLAT BACK TV
(UNIVERSAL MONITOR PLATE)
screwdriver(Not included)
N
ROUND BACK TV
(UNIVERSAL MONITOR PLATE)
First, make sure the diameter of the bolt(A-E) fits your TV. Then, please see the diagram above.
You will need to thread the bolt into the TV using the correct washer (F) and spacer (G or H) if
necessary with a screwdriver(Not included). Please make sure the monitor brackets(N) are vertically
centered and level with each other.
N
H/G

screwdriver
(Not included)
Attaching TV to TV Plate(M) and Mananging the Wires
Safety lock(K)
Insert the safety lock in the bottom of
the bracket(N) and then tighten the
screws in the safe lock(K).
monitor bracket(N)
Height adjustable vertical bracket(N)
Adusting the Height of the TV
Step 6
first choice
second choice
third choice
If you find your TV set is too close to the base, please take off the TV from the stand.
Then, change to the second choice or third choice to allow more space between TV and
the tempered glass base (O).
First choice Second choice Third choice
(K) Safety lock 2