PetPal PA 300 User manual

1
TM
TM
PetPal
PetPal
Training Systems
Training Systems
PetPal PA300
Electronic Dog Trainer
Owner’s Manual

2

3
TABLE OF CONTENTS
• Table of Contents......................................... 3
• Introduction.................................................. 4
• Package Contents......................................... 5
• Model Features............................................. 5
• Parts and Functions...................................... 6
• Turning ON and OFF................................... 10
• Adjusting and Positioning
Your Collar for Proper Fit............................ 11
• Testing.......................................................... 12
• Reprogramming ........................................... 13
• Important Safety Notes ................................ 14
• Maintenance................................................. 15
• Warranty ...................................................... 15
• FCC Compliance.......................................... 15
• Contact Information..................................... 16

4
Congratulations and thank you for purchasing our
PetPalTM Training Systems Collar. The PetPalTM
series represents the absolute latest technological
advancement in the Electronic Dog Training World. It
offers Maxx-Range™, the industry’s only internally
woven antenna in the collar. With up to a 300 yard
range, they are perfect for household use. PetPalTM
series collars feature sixteen levels of stimulation
intensity, with an easy ‘no-look’ clicking intensity
selection dial. Easy one hand operation allows for
maximum control and safety. This model includes
both the Continuous Stimulation and the Beep
function. The collars are 100% waterproof and can be
worn even when the dog is submerged. The PetPalTM
Series Dog Training Collar is durable, safe and very
humane when used correctly. The automatic safety
shut-off feature stops the stimulus from both the
transmitter and the receiver to prevent accidental or
prolonged stimulation.
INTRODUCTION
IMPORTANT NOTE:
Please read this owner’s manual in its entirety before
operating this unit. Should you have any questions
about our collars or their operation please contact our
Customer Service department (see back page for
address and phone number information).

5
PACKAGE CONTENTS
• Transmitter
• Collar Receiver
• Test Light
• Owner’s Manual
• 3 Volt Batteries for collar included
• Transmitter battery not included (Transmitter uses a
9 volt battery)
MODEL FEATURES
• Digital Technology
• Up to 300 yard range
• Lightweight, compact collar and transmitter
• 16 adjustable intensity levels of Constant
Stimulation
• Beeping Tone
• Gentle Touch System™ Extra Mild Stimulation
• MAXX-Range™ Invisible, Embedded Collar
Antenna
• Built in safety shut-off

6
Transmitter
(PA300 shown)
PARTS & FUNCTIONS
Intensity
Selection Dial
Antenna
LED
Indicator
Light
Magnet
Indicator
(Red Mark
in back)
Constant
Stimulation
Button
Beep
Button
Lanyard
attachment
Battery
compartment
(in back)

7
PARTS & FUNCTIONS CONT.
Intensity Selection Dial
The intensity selection dial allows you to choose between
sixteen different levels of stimulation for very precise control.
Transmitter Antenna
Be sure to check that the antenna is securely fastened to the
transmitter before each use. Hand-tightened only. Be careful
when screwing the antenna into the transmitter: over-
tightening can cause damage to the antenna or the antenna
mount.
Magnet Indicator (Red Mark)
The RED mark indicates the location of the magnet in the
transmitter. The indicator is used to turn the receiver ON/OFF
and for ID programming.
Transmitter Indicator Light
When any of the buttons on the transmitter is pushed, the RED
light will turn on to indicate that the transmitter is being
operated. When the battery is low, the RED light will flash
rapidly.
Remote Training Buttons
. Pressing the “CONT” button gives a Continuous Stimulation.
Pressing the “BEEP” button emits an audible beep.
Important Note:
There is a delay on the remote buttons, and the user
must press and hold the button for at least 1/2 second
in order to emit a shock or beep. This feature was
added to prolong battery life.

8
PARTS & FUNCTIONS CONT.
Collar Receiver
LED
Indicator
Light
Red Mark
(Magnetic
Switch
Indicator)
Collar Belt with
Embedded
Receiver
Antenna
Electrodes
Battery
Compartment
Cap
Magnet

9
Collar LED Indicator Light
The red LED light on the collar unit will flash to
indicate the unit is ON. When the battery in the collar
unit has a sufficient charge, the red LED light will
flash about once every two seconds while the unit is
ON. When the collar battery has a low charge and
needs to be replaced, the red LED will flash rapidly
(about 3 times every 2 seconds) while the unit is ON.
Battery Compartment Cap
The collar requires two 3 volt batteries (included in
package).
Electrodes
Electrodes should make good contact with the skin.
For more information on the proper fit of the collar,
see page 11.
Collar Belt with Embedded Receiver Antenna
The embedded collar antenna is woven into the collar
belt, and it is about 4 inches long. You should be able
to feel the embedded antenna on the nylon belt.
PARTS & FUNCTIONS CONT.
WARNING
Do not cut the part of the collar belt that has the em-
bedded antenna. Doing so will damage the antenna
and may result in severely decreased receiver range.

10
TURNING THE UNIT ON AND OFF
Turning the Collar Unit ON
1. Hold the Red Mark (Magnet
Indicator) on the back of the
transmitter directly against the Red
Mark (Magnet Indicator) on the
side of the collar receiver. You can
also use the magnet on the belt to
turn the collar ON.
2. A small red LED light (next to the Red Mark) will light up
solid for about 1 second, and then will begin to flash.
3. You may remove the Transmitter away from the Collar
Unit as soon as the LED light starts flashing
4. The Collar Unit is now ON. The LED light should
continue to flash to indicate the ON status. (Note: The
Transmitter is always in a permanent sleep state. It is only
ON when a button is being pressed and held for at least
1/2 second, and it does not need to be turned off by the
user).
Turning the Collar Unit OFF
1. Hold the Red Mark (Magnet Indicator) on the back of the
transmitter directly against the Red Mark (Magnet
Indicator) on the side of the collar receiver. You can also
use the magnet on the belt to turn the collar ON.
2. A small red LED light (next to the Red Mark) will light up
solid for about 1 second, and then will begin to flash.
3. You may remove the Transmitter away from the Collar
Unit as soon as the LED light starts flashing
4. The Collar Unit is now OFF. The LED light should no
longer flash, which indicates that the collar is now OFF.