PEUGEOT 208 T16 User manual

SYSTEM
USER GUIDE
Version 24/04/2015

SUMMARY
Page 2/67
Version 24/04/2015
-General information Page 03
-Driver systems Page 04 to 11
BRK Unit (central console) page 04
Engine map selection page 06
Auxiliary functions page 07
Start assistance system page 08
Calibration and zero of sensors page 09
Engine map update page 11
-Display (Alarms page 25) Page 12 to 25
-Wintax Page 26 to 67
Ethernet configuration page 26
User profile installation page 27
Download data –Ethernet page 34
Download data –USB key page 36
Open data page 41
User profile page 42
Events page 43
Layouts page 44
Chanels list page 67

Essential sensors
The following sensors are used by the system, not having those sensors working properly will generate
important consequences for the performance and reliability of engine and gearbox:
−RPM
−Throttle pedal position
−Throttle position
−Atmospheric pressure, pressures before and after throttle
−Turbo RPM
−Ambient temperature, air intake temperature and exhaust gaz temperature
−Temperature and pressure of the cooling circuit
−Knocking sensor
−Temperature and pressure of engine oil
−Temperature of gearbox and rear diff oil
−Barrel position + gearbox command effort
−Vehicle speed
−Rear brake and handbrake pressure
−PEAL accumulator pressure
−Fuel pressure
Optional sensors
The following sensors can be used in test but are forbidden in official competition:
−Wheel speed (part number 1E1326775A)
−Brake pad temperature (part number 903895318A)
General informations
Page 3/67
Version 24/04/2015

BRK Unit (central console)
Power : power supply of actuators (PEAL, fans, …)
Map selection
Indicators and swap page of display
Lights and light pods
Starter
Accessories
Page 4/67
Version 24/04/2015

BRK Unit (central console)
Maps
1. Stage / Road: dedicated map selection
2. Gravel / Asphalt: surface selection
3. Throttle : selection of the performance mode (3 maps available)
4. Launch : selection of launch control (2 choices)
Indicators and swap page of display
1 & 3. Indicators: one push starts indicators during 25s, a push on both indicators stops it.
A push on both indicator buttons starts the warning
2. Swap page: short press display the next page of the mode
long press change the display mode (driver / mechanics)
Lights and light pods
1. Lights: a press for a change: OFF position light dimmed headlights OFF
When dimmed headlights are ON, push on the button of the extremity of the wiper switch for high
beam
2-3-4. light pods: need the high beam lights ON
Starter
A short push launches the starter until the engine starts (maxi 5s)
Accessories
1. Heater fan
2. Horn
3. Activation of auxiliary functions
1 2 3 4
1 2 3 4
1 2 3
1 2 3
Page 5/67
Version 24/04/2015

Map selection
Engine maps
- 3 maps per surface are available
- map 1 is the most performing map for high grip surfaces, map 3 is the less aggressive map for low grip
surfaces, map 2 is in between
Surface selection
The selection of the surface adjusts the vehicle speed to the tyres circumference and the throttle maps (as
shown above)
Launch control
There are 2 choices but there is no difference between both maps (for the moment)
Performance level
Tarmac Gravel
Torque
Throttle
pedal
/ body
map
Torque
Throttle
pedal
/ body
map
Throttle 1 Full Hard Full Hard
Throttle 2 Full Soft Reduced Soft
Throttle 3 Reduced Hard
Max reduced
Soft
Page 6/67
Version 24/04/2015

Fuel pump
- The fuel pumps in the tank runs a few seconds after a Power ON
- The fuel pumps in the tank runs when the engine is running
- To drain the fuel tank or for a fuel sample:
Main switch ON and power OFF
Keep pushing auxiliary function and push on the Power button
Radiator fan
- The fan starts running when water temperature is above 80°then stops below 75°
- Fan can be forced:
Main switch ON and power OFF
Keep pushing the heater fan button and push on the Power button
- The fan stops running 3s after the engine stops
Engine Crank
- To prime the oil pump and circuit before a first start of the engine, please follow the procedure:
Main switch ON and power OFF
Push on the horn button then on the start button. Keep pushing until you reach 5 bars of oil pressure
Auxiliary functions
Page 7/67
Version 24/04/2015

Activation of the launch control
1. Select the launch control strategy: push on the launch button to select Launch 1 or 2 (selection displayed on the
dashboard)
2. When you are stopped on the start line, check you are in road mode
3. Clutch
4. Engage 1st gear
5. Pull hand brake (pressure must be higher than 10 bars)
6. Select the stage mode, the strategy is activated
7. Push full throttle 5 seconds before the start time
8. The message "GO !!!" is displayed when the optimum pressure of air circuit is reached
9. When you want to start the stage, release the hand brake and clutch in the same time, keep full throttle during
the launch. Depending on the grip, the driver has to manage the clutch (and the throttle pedal in case of very low
grip condition).
Start Assistance System
Page 8/67
Version 24/04/2015

Calibration of throttle pedal and throttle body
Important:
The calibration must be done:
- after the replacement of the throttle pedal of throttle body
- after the replacement of the ECU
- after the replacement of the engine
Procedure
1. Engine must be OFF and gearbox in neutral
2. Main switch OFF
3. Keep pushing the throttle pedal
4. Main switch ON
5. Wait for the 1st message on the display
6. Then release the throttle pedal when displayed
7. Wait for the message of calibration success
8. Main switch OFF
If you get a message of calibration failure, please proceed to a new calibration procedure
Page 9/67
Version 24/04/2015

Zero of the steering wheel position sensor
Procedure
1. The engine must be OFF, the spacer (straight tool number 1E4126405A-OUT) must be fitted in the left part of the steering
rack
2. Main switch ON and Power OFF
3. Keep pushing the heater and auxiliary functions button until the message "ZERO OK« is displayed
4. Main switch OFF
5. Remove the spacer from the steering rack
Information
The zero must be done:
- after the replacement of the steering wheel position sensor
- after the replacement of the ECU
- after any work on the steering system
« ZERO OK »
Page 10/67
Version 24/04/2015