Philio Technology Corporation PAN34 User manual

Specification
Operating Voltage 100 -240VAC 50-60Hz
Maximum Load Re i tive load 5A max.
Range Minimum 40m indoor 100m outdoor line of ight
Operating Temperature 0°C - 40°C
Humidity Up to 85% max.
Storage Temperature -20°C to 60°C
Location Indoor u e only
Frequency Range 868.40MHz; 869.85MHz (EU)
908.40MHz; 916.00MHz (USA/Canada)
920.90 MHz, 921.70 MHz, 923.10 MHz (Taiwan)
RF Maximum Power +10dBm (Peak), -10dBm (Average)
OTA Support
FCC ID RHHPAN34
Dimen ion 47.5 x 39 x16 mm
Wire 0.75mm² , 18AWG
** Specification are ubject to change and improvement without notice.
Troubleshooting
Symptom Cause of Failure Recommendation
The PAN34 not working
and LED off
1. The PAN34 i not
connect to the Main
power
2. The PAN34 break
down
1. Check power connection
2. Don’t open up the PAN34 and
end it for repair.
The hutter move direction
i rever e
Wrong connection of NC
and NO to the motor
Swap the NC NO connection
PAN34 LED light work fine
But can not control
1. No a ociation etting
2. Same frequency
interference
3. S1 or S2 are both
pre ed in Two Pu h
Button witch type,
PAN34 would not accept
RF command.
1. Carry out a ociation
2. Wait for a while to re-try
3. Relea e S1 and S2
Fig 1. Assembling Installation and wiring
1. Put the in wall PAN34 into a wall box and connect the AC power wire L,N to PAN34
connector L, N.
2. Connect the wall witch to the PAN34 a Fig1.
2

3. To manually witch up and down of the hutter, imply pre the external witch S1 or S2.
The detail i de cribed in 5-2.
4. PAN34 built in meter function and can read the Watt, KWh, V(Voltage), I(Current), PF
(Power Factor) of the load by u ing Z-Wave command cla , u er can et a thre hold
current to get the warning cau ed by abnormal operation
5. PAN34 have overload protection function and can help to prevent hort circuit cau ed by
load.
For Instruction to http: www.philio-tech.com
DANGER
Danger of electrocution!
All work on the device may be performed only by a qualified and licen ed electrician. Ob erve
national regulation .
Any work introducing change into the configuration mu t be alway performed with
di connected voltage.
Choosing a Suitable Location
1. Do not locate the Module facing direct unlight, humid or du ty place.
2. The uitable ambient temperature for the Module i 0°C~40°C.
3. Do not locate the Module where exi t combu tible ub tance or any ource of heat, e.g.
fire , radiator , boiler etc.
4. After putting it into u e, the body of Module will become a little bit hot of which phenomenon
i normal.
Adding to Z-Wave
TM
Network
In the front ca ing, there i an include button with LED indicator below which i u ed
to carry out inclu ion, exclu ion, re et.
The table below li t an operation ummary of ba ic Z-Wave function . Plea e refer
to the in truction for your Z-Wave
TM
Certificated Primary Controller to acce the
Setup function, and to include/exclude/re et device .
Function Description LED Indication
No node ID The Z-Wave Controller doe not allocate
a node ID to the PAN34.
LED 2- econd on, 2-
econd off
Add
(Cla ic
Inclu ion)
1. Put your Z-Wave controller into
inclu ion mode by following the
in truction provided by the
controller manufacturer.
One pre one fla h LED
 To upport handling of
the device when already
in talled the external
witch can be u ed for
inclu ion or exclu ion for 3
minute after power up.
2. Pre ing Include button three time
within 2 econd will enter inclu ion
mode.
SmartStart 1. The product ha a DSK tring. Key
in the fir t five digit to initiate the
SmartStart proce , or can QR
code.
3

Ex: DSK: 18112-24021- 48001-
62259-57092-27453-08187-47408
2.
SmartStart
enabled product can
be added into a Z-Wave™ network
by canning the Z-Wave™ QR
Code on the product, with a
controller providing SmartStart
inclu ion. No further action i
required and the SmartStart product
will be added automatically to the
clo e t network within 10 minute of
being witched on.
Notice:
The QR Code can be found on the
device PAN34 or in the box.
Remove
(Exclu ion)
1. Put your Z-Wave controller into
exclu ion mode by following the
in truction provided by the
controller manufacturer.
One pre one fla h LED
 To upport handling of
the device when already
in talled the external
witch can be u ed for
inclu ion or exclu ion for 3
minute after power up.
2. Pre ing Include button three
time within 2 econd will enter
exclu ion mode.
Node ID ha been excluded. LED 2 On, 2 Off (No
node ID)
Re et 1. Pre ing Include button three time
within 2 econd will enter inclu ion
U e thi procedure only in
the event that the primary
mode. controller i lo t or
otherwi e inoperable.
2. Within 1 econd, pre Include
button again for 5 econd .
3. ID are excluded. LED 2 On, 2 Off (No
node ID)

Adding a node ID allocated by Z-Wave Controller mean inclu ion. Removing a node ID
allocated by Z-Wave Controller mean exclu ion.

Failed or ucce in including/excluding the node ID can be viewed from the Z-Wave
Controller.
Sometime people are not ea y to execute exclu ion or inclu ion e pecially when PAN34
already in talled in a wall box. To olve thi i ue, PAN34 upport a pecial feature that can
u e S1 or S2 to execute “exclu ion, inclu ion, Re et or A ociation” at the fir t 3 minute
when fir t time connect to main power.
LED Indication
There i a LED for identify function in the front ca e. PAN34 upport the indicator ID
0x50 (Identify) and Propertie ID 0x03, 0x04 and 0x05.
To di tingui h what mode the PAN34 i in, view from the LED for identification.
State Type LED Indication
Motor
activate
No matter up or down, clo e or open, Led will fla h every econd
while Motor activate.
When S1 or S2 clo e to L, the LED will fla h even when the motor
top by it elf, thi i to let u er know the S1 or S2 till clo e and
not been relea e yet.
No node ID Under normal operation, when the PAN34 ha not been allocated
4

a node ID, the LED fla he on and off alternately at 2- econd
interval . By pre ing S1 S2 or Include button, it will top fla hing
temporarily.
Learning When PAN34 i in learning mode, LED fla he on and off
alternately and repeatedly at 0.5 econd interval .
Overload When overload tate occur , the PAN34 i di abled and LED
fla he on and off alternately at 0.2 econd interval . PAN34 will
end Notification type=8, Notification State=0x08 to Group1,
Overload tate can be cleared by di connect and reconnect the
PAN34 to the main power
Moving Range Calibration
1. It i important to carry out a hutter calibration proce before you control the
hutter to move. Pre inclu ion button over 3 econd and relea e before the 6th
econd, the roller hutter controller will tart the hutter calibration proce . The
proce i compo ed of three continue tage . The hutter move to the TOP in fir t
tage, and move to the BOTTOM in econd tage, and move to the TOP again in
third tage. Then PAN34 will know the total range from the BOTTOM to the TOP.
2. During the hutter calibration proce , any emergencie happen you can pre
and relea e the include button to top the proce .
3. If u er found the direction i rever e, thi may cau e by the wrong connection of
NC and NO to the motor, plea e exchange NC and NO connection and execute
calibration proce again.
4. For afe i ue, plea e elect the motor which can top by it elf when go to bottom
end or top end.
Programming
1. Basic Command Class
The PAN34 will re pond to BASIC and BINARY command that are part of the
Z-Wave y tem.
1.1 BASIC_GET
When PAN34 receive Ba ic Get Command, it will end Ba ic Report Command
to report the po ition of the hutter. When the report value i 0x00, that mean the
hutter i at the Bottom, if the report value i 0x63 that mean the hutter i at the
Top, any other value between 0x01~0x62 imply Shutter at the po ition between
top and bottom.
Ba ic Get Command: [Command Class Basic, Basic Get]
Ba ic Report Command：
[Command Class Basic, Basic Report, Value = 0x00 (BOTTOM)]
[Command Class Basic, Basic Report, Value = 0x01~0x62 (Between BOT-
TOM and TOP)]
[Command Class Basic, Basic Report, Value = 0x63 (TOP)]
1-2 BASIC_SET
5

PAN34 can accept Ba ic Set Command which value i either (0x00) Bottom or
Top (0x63) or (0x01-0x62) the po ition between TOP and Bottom. Other value
(0x64-0xFE) i not acceptable.
[Command Class Basic, Basic Set, Value = 0x63] control the shutter to
the top (0x63)
[Command Class Basic, Basic Set, Value = 0x00(0)] control the shutter to
the bottom(0x00)
[Command Class Basic, Basic Set, Value = 0xFF] control the shutter to
the most recent (non-zero) level.
[Command Class Basic, Basic Set, Value = 0x01-0x62] control the shutter
to the position between bottom and top
2. Multilevel Switch Command Class (Version 3)：
：：
：
2-1 MULTILEVEL SWITCH SET:
PAN34 can accept Multilevel Switch Set Command which value i either (0x00) Bot-
tom or Top (0x63) or (0x01-0x62) the po ition between TOP and Bottom. Other value
(0x64-0xFE) i not acceptable.
[Command Class Multilevel Switch, Multilevel Switch Set, Value = 0x63]
control the hutter to the top (0x63)
[Command Class Multilevel Switch, Multilevel Switch Set, Value =
0x00(0)] control the hutter to the bottom(0x00)
[Command Class Multilevel Switch, Multilevel Switch Set, Value =
0xFF(255)] control the hutter to the the most recent (non-zero) level.
[Command Class Multilevel Switch, Multilevel Switch Set, Value = 0x01-
0x62] control the hutter to the po ition between Bottom and Top.
2-2 MULTILEVEL SWITCH GET
:
When PAN34 receive Multilevel Switch Get Command, it will end Multilevel Switch
Report Command to report the po ition of the hutter. When the report value i 0x00,
that mean the hutter i at the Bottom, if the report value i 0x63 that mean the hut-
ter i at the top, any other value between 0x01~0x62 imply hutter at the po ition be-
tween top and bottom.
Switch Multilevel Get Command：
[Command Class Multilevel Switch, Multilevel Switch Get]
Multilevel Switch Report Command：
[Command Class Multilevel Switch, Multilevel Switch Report,
Value = 0x00(BOTTOM)]
[Command Class Multilevel Switch, Multilevel Switch Report,
Value = 0x01~0x62(Between BOTTOM and TOP)]
[Command Class Multilevel Switch, Multilevel Switch Report,
Value = 0x63 (TOP)]
2-3 MULTILEVEL SWITCH START LEVEL CHANGE:
6

Thi i the command which u er can move the hutter up to the top or down to the
bottom.
[Command Class Multilevel Switch, Multilevel Switch Start Level Change,
Up Down Value]
2-3.1 Up Down Bit:
If Up/Down Bit=0x00 Shutter move up
If Up/Down Bit=0x01 Shutter move down
If Up/Down Bit=0x03 no move
[Command Class Multilevel Switch, Multilevel Switch Start Level
Change, Up Down=0x00] control the shutter to the top (0x63)
[Command Class Multilevel Switch, Multilevel Switch Start Level
Change, Up Down=0x01] control the shutter to the bottom (0x00)
[Command Class Multilevel Switch, Multilevel Switch Start Level
Change, Up Down=0x03] Don't move the shutter or stop the moving
shutter
ATT. 1. Ignore Start Level、 Start Level、 Dimming Duration、 Inc/Dec、 Step ize can
not be u ed.
2
.
PAN34 can not control the speed of motor.
3. It may have ome di tance error cau ed by motor tart up time.
4. If u er found the error become ignificant, you may u ing S1 or S2 move
hutter to the end or remote move hutter to 0% and 100%, and that will
automatically calibrate thi error.
2-3.4 MULTILEVEL SWITCH STOP LEVEL CHANGE:
When receive Multilevel Switch Stop Level change Command PAN34 will top the
motor.
Z-wave’s Groups introduction (Maximum 5 node )
There i only one group called Lifeline，there i only 5 node for Group1 which up-
port MULTILEVEL_SWITCH_REPORT、METER_REPORT_COMMAND_V3、
ALARM_REPORT and DEVICE_RESET_LOCALLY_NOTIFICATION.
3-1 Device reset locally notification :
When PAN34 i re et manually, it will end a DEVICE_RESET_LOCALLY_
NOTIFICATION to the node of group 1.
3-2 Report the shutter position ：
：：
：
Every time when u er pre S1 or S2 and let hutter to move, PAN34 will report the
po ition tatu to controller, and at the moving proce when change over 10%
PAN34 will end Multilevel Switch Report to Group 1 a well.
Multilevel Switch Report：
Ex. Report po ition at 30%
[Command Cla Multilevel Switch， Multilevel Switch Report，Value = 30(%)]
3-3 Meter Command Class：
：：
：
The Switch will report it (1) in tant Power Con umption (Watt) or (2) accumulated
7

power con umption(KWH) or (3) AC load Voltage (V) or (4) AC load current ( I ) (5)
load power factor (PF) to Z-Wave Controller after receive the Meter Get Command
from Z-Wave Controller.
When the power con umption of load vary over 5%, it will end Meter report to the
node of Group a well
3-3.1 Instant Power Consumption (Watt) of Switch
When receiving Meter Get Command, it will report Meter Report Command to the
node a ked.
Meter Get Command: [Command Class Meter, Meter Get, Scale
=0x02(W)]
Meter Report Command:
[Command Class Meter，Meter Report，Rate Type = 0x01，Meter
Type = 0x01，Precision = 1，Scale = 0x02，Size = 4，Meter
Value(W) ]
Example:
Meter Value 1 = 0x00 (W)
Meter Value 2 = 0x00 (W)
Meter Value 3 = 0x03 (W)
Meter Value 4 = 0xEA (W)
Meter(W) = Meter Value 3 *256 + Meter Value 4 = 100.2W
3-3.2 Accumulated Power Consumption (KW h)
When receiving Meter Get Command, it will report Meter Report Command to
the node a ked.
Meter Get Command: [Command Class Meter, Meter Get, Scale = 0x00
(KW h)]
Meter Report Command:
[Command Class Meter，Meter Report，Rate Type = 0x01， Meter
Type = 0x01， Precision = 2，Scale = 0x00，Size = 4，Meter Value
(KWh)]
Example:
Scale = 0x00 (KWh)
Preci ion = 2
Size = 4 Byte (KW/h)
Meter Value 1 = 0x00(KWh)
Meter Value 2 = 0x01(KWh)
Meter Value 3 = 0x38(KWh)
Meter Value 4 = 0xA3(KWh)
Accumulated power con umption (KW/h) = (Meter Value 2*65536) + (Meter Value
3*256) + (Meter Value 4) = 800.35 (KW/h)
3-3.3 AC load Voltage (V)
When receiving Meter Get Command, it will report Meter Report Command to the
node a ked.
Meter Get Command: [Command Class Meter, Meter Get, Scale
=0x04(V)]
Meter Report Command:
8

[Command Class Meter，Meter Report，Rate Type = 0x01，Meter
Type = 0x01，Precision = 1，Scale = 0x04，Size = 2， Meter Value(V)]
Example:
Scale = 0x04 (V)
Preci ion = 1
Size = 2 (2 Byte of V)
Meter Value 1 = 0x09(V)
Meter Value 2 = 0x01(V)
AC load Voltage = (Meter Value 1*256) +(Meter Value 2)= 230.5 (V)
3-3.4 AC load current ( I
II
I )
When receiving Meter Get Command, it will report Meter Report Command to the
node a ked.
Meter Get Command: [Command Class Meter, Meter Get, Scale =
0x05(I
II
I)]
Meter Report Command:
[Command Class Meter，Meter Report，Rate Type = 0x01，Meter
Type = 0x01，Precision = 2，Scale = 0x05，Size = 2，Meter Value(I
II
I)]
Example:
Scale = 0x05 (I)
Preci ion = 2
Size = 2 (2 Byte of I)
Meter Value 1 = 0x01(I)
Meter Value 2 = 0x21(I)
AC load current = (Meter Value 1*256) +(Meter Value 2)= 2.89 (A)
3-3.5 load power factor (PF)
When receiving Meter Get Command, it will report Meter Report Command to the
node a ked.
Meter Get Command: [Command Class Meter, Meter Get, Scale =
0x06(PF)]
Meter Report Command:
[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type
= 0x01， Precision = 2，Scale = 0x06，Size = 1 Bytes，Meter
Value(PF)]
Example:
Scale = 0x06 (PF)
Preci ion = 2
Size = 1 (1 Byte of PF)
Meter Value 1 = 0x63(PF) (It mean that the load power factor i 0.99)
3-3.6 Reset Accumulated Power Consumption (KWh)
Whenever re- tart counting the accumulated power con umption i needed, you can
u e Meter Re et Command to clear it.
Meter Re et Command：[Command Class Meter, Meter Reset]
4 Notification Report Command：
：：
：
9

When PAN34 detect Overload, it will end Notification Report to Group1, Notification
_Type = 0x08, Notification State = 0x08. When it receive Notification Get command
with Notification Type = 0x08 and the PAN34 not in overload tatu , it will end Notifi-
cation Report, Notification Type = 0x08, Notification State = 0x00.
When PAN34 detect an overload power, it will end Notification Report to Group1.
[Command Cla Notification, Notification Report, Notification Type = 0x08,
Notification State = 0x08 (Overload)]
[Command Cla Notification, Notification Report, Notification Type = 0x08,
Notification State = 0x00 (Normal)]
5. Z-Wave’s Configuration
Configura
tion
Parameter
Function Size
(Byte)
Value Unit Default Description
1 Watt
Meter
Report
Period
2 0x01-
0x7FFF
5 720 0: Di able auto
Report
1~0x7FFF: 5
~45 hour
2 External
witch
type
1 1-2 2
1: One Pu h button
2:Two Pu h button
3 Total
moving
time of
curtain
2 0-6000 0.1
Second
0
0: The time depend
on Moving Range
Calibration
1~6000: 0.1 ~600
4 Watt 1 1-5 Watt 1
The thre hold i a
thre hold
judgment for motor
running or not
5
Watt
differential
1 0-1 1
0: It will not report
Watt when change
over 5%
1: It will report watt
value when the
differential i over 5%
6 Timer
off et for
motor
tart
running
2 0-255 0.01
econd
50
0-255: 0 ~ 2.55
50 = 0.5
5-1 Watt Meter Report Period:
If the etting i configured for 1hour ( et value =720), the PAN34 will report it in tant
power con umption every 1 hour to the node of Group 1. The maximum interval to
report it in tant power con umption i 45 hour (5 *32767/3600=45hr). Default
value i 1 hour. If the etting value i 0, the auto report function of meter Watt will be
di abled.
5-2 External switch type
5-2-1 One Pu h Button：
When the configuration etting i One Pu h Button, only S1 input will be valid.
The control moving command can be accepted in thi witch type while the
hutter i moving. In thi witch type, the inclu ion/exclu ion/re et function can
al o be fulfilled by pre ing S1 ju t like the operation of include button.
10