Philips AVENT SCD499/00 User manual

SCD499

2

3
8
9
10
11
12
1

4

SCD499
ENGLISH 6
DANSK 18
DEUTSCH 30
 43
ESPAÑOL 57
SUOMI 69
FRANÇAIS 81
ITALIANO 93
NEDERLANDS 105
NORSK 117
PORTUGUÊS 128
SVENSKA 141
TÜRKÇE 152

6
Introduction
Philips Avent is dedicated to producing caring, reliable products that give parents the reassurance
they need.This Philips Avent baby monitor provides round-the-clock support by ensuring you can
always hear your baby clearly without any distracting noise.The DECT technology guarantees zero
interference from other wireless appliances and a clear signal between the baby unit and the parent
unit.
General description (Fig. 1)
ABaby unit
1 On/off button 3
2 Temperature sensor
3 ON light
4 Volume +/– buttons
5 PAGE button
6 Display
7 Nightlight
8 Play/stop button E
9 Lullaby button K
10 Nightlight button Q
11 Microphone
12 Adapter
13 Small plug
14 Battery compartment lid
15 Socket for small plug
16 Battery compartment
BParent unit
1 Sound level lights
2 Display
3 TALK button
4 MENU button
5 On/off button 3
6 LINK light
7 Opening for belt clip and neck strap
8 Volume +/– buttons
9 OK button
10 Microphone
11 Loudspeaker
12 Battery compartment
13 Belt clip
14 Battery compartment lid
15 Neck strap
16 Adapter
17 Charger
18 POWER light
CDisplay
1 Ñ° Room temperature indication
2 QNightlight indication
3 KLullaby symbol
4 TBattery symbol
5 oVolume indication
6 RMicrophone sensitivity indication
7 URoom temperature above temperature set in menu
ENGLISH

8 IRoom temperature below temperature set in menu
9 O‘No connection between units’ message
10 {‘Volume level’ message
11 SMessage when lullaby is interrupted
DTravel pouch
Important
Read this user manual carefully before you use the appliance and save it for future reference.
This baby monitor is intended as an aid. It is not a substitute for responsible and proper adult
supervision and should not be used as such.
Check if the voltage indicated on the adapters of the baby unit and the charger corresponds
to the local mains voltage before you connect the appliance.
Use and store the appliance at a temperature between 10°C and 40°C.
The appliance is suitable for mains voltages from 220 to 240V.
Do not expose the baby monitor to extreme cold or heat or to direct sunlight.
Make sure the baby unit and the cord are always out of reach of the baby (at least 1 metre/
3 feet away).
Never place the baby unit inside the baby’s bed or playpen.
Never cover the baby monitor with a towel or blanket.
Never immerse any part of the baby monitor in water or any other liquid.
Never use the baby monitor in moist places or close to water.
Except for the battery compartments, do not open the housing of the baby unit and parent
unit in order to prevent electric shock.
Only use the adapter supplied to connect the baby unit to the mains.
Only use the charger supplied to charge the parent unit.
The adapters contain a transformer. Do not cut off the adapters to replace them with other
plugs, as this causes a hazardous situation.
If the adapter of the baby unit is damaged, always have it replaced with one of the original
type in order to avoid a hazard.
If the charger or the adapter of the charger is damaged, always have the charger replaced
with one of the original type in order to avoid a hazard.
Always place non-rechargeable batteries of the correct type in the baby unit to avoid the risk
of explosion.Always use rechargeable batteries of the correct type for the parent unit.
Since continuous transmission is prohibited, you only hear your baby when it makes sounds.

This Philips Avent appliance complies with all standards regarding electromagnetic elds (EMF). If
handled properly and according to the instructions in this user manual, the appliance is safe to use
based on scientic evidence available today.
Preparing for use
Baby unit
You can use the baby unit from the mains or on batteries. Even if you are going to use the unit from
the mains, we advise you to insert batteries.This guarantees automatic back-up in case of mains
failure.
Mains operation
1 Put the small plug in the baby unit and put the adapter in a wall socket (Fig. 2).
Battery operation
The baby unit runs on four 1.5V R6 AA batteries (not included). We strongly advise you to use
Philips LR6 PowerLife batteries.
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
ENGLISH 7

Make sure your hands and the unit are dry when you insert the batteries.
1 Turn the battery compartment lid to the left ( ÁOPEN) with the palm of your hand. (Fig. 3)
2 Remove the lid.
3 Insert four 1.5V R6 AA batteries (Fig. 4).
Place two batteries on top of each other and make sure the + and – poles of the batteries
point in the right direction.
4 Put the battery compartment lid back onto the unit and turn it to the right (CLOSE ª) with
the palm of your hand to close it. (Fig. 5)
Note:When the batteries are running low, the battery symbol appears on the display.
Parent unit
Battery operation
The parent unit runs on two rechargeable 1.2V AAA NiMh batteries that are supplied with the
appliance.
Make sure your hands and the unit are dry when you insert the batteries.
1 Slide the battery compartment lid downwards to remove it (Fig. 6).
2 Insert the two rechargeable batteries (Fig. 7).
Make sure the + and – poles of the batteries point in the right direction.
3 Slide the battery compartment lid back onto the back of the parent unit until it locks into
position (‘click’) (Fig. 8).
4 Put the adapter in a wall socket and place the parent unit in the charger (Fig. 9).
The POWER light on the charger lights up.
5 Leave the parent unit in the charger until the batteries are fully charged

parent unit and let it charge continuously for at least 10 hours.
Charging normally takes 8 hours, but it takes longer when the parent unit is switched on
while charging.To keep the charging time as short as possible, switch off the parent unit
during charging.
The POWER light on the charger stays on, even when the batteries are fully charged.
When the batteries are fully charged, the parent unit can be used cordlessly for at least 24
hours.
Note:The operating time of 24 hours is based on the assumption that the baby unit transmits 25% of
the time and is in standby mode for the rest of the time (when the baby does not make any sound).
Note: When the parent unit batteries are charged for the rst time, the operating time is less than 24
hours.The batteries only reach their full capacity after you have charged and discharged them four times.
Note:When the battery symbol on the display is empty and the parent unit beeps, the batteries are
running low. Place the parent unit in the charger.
Note:When the parent unit is not in the charger, the batteries gradually discharge, even when the parent
unit is switched off.
Mains operation
1 Make sure you have inserted the rechargeable batteries in the parent unit.
2 Put the adapter of the charger in the wall socket and place the parent unit in the
charger (Fig. 9).
,
,
,
,
,
,
,
ENGLISH8

The POWER light on the charger lights up.
Using the appliance
1 Place the parent unit and the baby unit in the same room to test the connection (Fig. 10).
Make sure the baby unit is at least 1 metre/3 feet away from the parent unit.
2 Press and hold the on/off button 3on the baby unit for 2 seconds. (Fig. 11)
The nightlight lights up briey.
The display lights up and indicates the current room temperature.
The ON light lights up.
3 Press and hold the on/off button 3on the parent unit for 2 seconds. (Fig. 12)
The sound level lights light up blue briey.
The display lights up and the battery symbol and the temperature indication appear on the
display.
The LINK light ashes red briey and then starts to ash green while the parent unit tries to
establish connection with the baby unit.
The LINK light on the parent unit ashes green until connection has been established.
This takes up to 30 seconds.The LINK light on the parent unit then lights up
green continuously (Fig. 13).
If no link is established after 30 seconds, the LINK light on the parent unit ashes red, the
parent unit beeps from time to time and the message Oappears on the display
of the parent unit.
4 Place the baby unit at least 1 metre/3 feet away from your baby (Fig. 14).
5 Position the parent unit within the operating range of the baby unit. Make sure it is at least
1 metre/3 feet away from the baby unit (Fig. 15).
For more information on the operating range, see section ‘Operating range’ below.
Operating range
The operating range of the baby monitor is 300 metres/900 feet in open air. Depending on the
surroundings and other disturbing factors, this range may be smaller. Indoors the operating range is
up to 50 metres/150 feet.
Dry materials Material thickness Loss of range
Wood, plaster, cardboard, glass
(without metal, wires or lead) < 30cm/12in 0-10%
Brick, plywood < 30cm/12in 5-35%
Reinforced concrete < 30cm/12in 30-100%
Metal grilles or bars < 1cm /0.4in 90-100%
Metal or aluminium sheets < 1cm/0.4in 100%
For wet and moist materials, the range loss may be up to 100%.
Features
Adjusting loudspeaker volume
1 Briey press the volume + and – buttons on the baby unit until the desired loudspeaker
volume for the baby unit has been reached (Fig. 16).
,
,
,
,
,
,
,
,
,
ENGLISH 9

2 Briey press the volume + and – buttons on the parent unit until the desired loudspeaker
volume for the parent unit has been reached (Fig. 17).
The displays give visual feedback on the volume settings of the units:
A: parent unit volume switched off / monitoring baby silently;
P : minimum volume (parent unit and baby unit);
}: maximum volume (parent unit and baby unit).
Note: If you press the volume + and – buttons too long, the volume is not adjusted.
Note:You only have to adjust the baby unit volume when you use the talk function (see below).
Note: If the volume is set to a high level, the units consume more power.
Talk function
You can use the TALK button on the parent unit to talk to your baby (e.g. to comfort your baby).
1 Press and hold theTALK button and talk clearly into the microphone (Fig. 18).
2 Release the TALK button when you have nished talking.
Note:When you press theTALK button, you can no longer hear your baby.
Silent baby monitoring
1 Briey press the volume down (–) button on the parent unit until the volume is switched off
completely (Fig. 19).
The volume is completely switched off when all sound level lights are out.
As long as the baby unit does not detect a sound, all sound level lights on the parent unit are
out (Fig. 20).
When the baby unit picks up a sound, one or more sound level lights on the parent unit
come on.The louder the sound, the more lights come on.
Nightlight
1 Briey press the nightlight button Qon the baby unit to switch on the nightlight. (Fig. 21)
Qappears on both displays.
2 Press the nightlight button Q again briey to switch off the nightlight.
The nightlight dims gradually before it goes out completely.
Qdisappears from both displays.
Note: If you press the nightlight button Qtoo long, the nightlight does not come on or go out.
Tip: Switch off the nightlight when you operate the baby unit on batteries.This saves power.
Paging the parent unit
If you have misplaced the parent unit and its volume is switched off, you can use the PAGE button
on the baby unit to locate the parent unit.
1 Briey press the PAGE button on the baby unit (Fig. 22).
Happears on both displays.
The parent unit automatically resets to medium volume level and produces a paging alert
tone.
2 To stop the paging alert tone, press the PAGE button again briey or press any button on the
parent unit.
Note: If you press the PAGE button too long, the parent unit does not produce the paging alert tone.
,
-
-
-
,
,
,
,
,
,
,
ENGLISH10

Lullaby function
1 Briey press the lullaby button K on the baby unit to select one of the ve lullabies
available. (Fig. 23)
2 Briey press the play/stop button Eto play the selected lullaby. (Fig. 24)
3 Briey press the OK button on the parent unit to interrupt the lullaby. Press the OK button
on the parent unit again to continue the lullaby (Fig. 25).
If you do not continue the lullaby within 60 seconds, the lullaby function switches off
automatically.
4 Briey press the play/stop button Eon the baby unit again to stop the lullaby. (Fig. 24)
Note: If you press the lullaby button Ktoo long, no lullaby is selected.
Belt clip and neck strap
If the batteries of the parent unit are sufciently charged, you can take the unit with you inside and
outside the house if you attach the unit to your belt or waistband with the belt clip or if you hang it
round your neck with the neck strap.This allows you to monitor your baby while you are moving
around.
Connecting the belt clip
1 Insert the small pin on the back of the belt clip into the opening on the back of the parent
unit (1).Turn the belt clip to the left (2) until it locks into position (‘click’) (Fig. 26).
Disconnecting the belt clip
1 Turn the belt clip to the right (1) and take it out of the opening (2) (Fig. 27).
Connecting the neck strap
1 Insert the small pin at the end of the neck strap into the opening on the back of the parent
unit (1).Turn the neck strap to the left (2) until it locks into position (‘click’) (Fig. 28).
Disconnecting the neck strap
1 Turn the neck strap to the right (1) and take it out of the opening (2) (Fig. 29).
Reset function
This function allows you to reset the parent unit and baby unit to the default settings.You can use
this function if problems occur that cannot be solved by following the suggestions in chapter
‘Frequently asked questions’. You have to reset each unit separately.
1 Press and hold the on/off button 3for 2 seconds to switch on the unit. (Fig. 11)
2 Then immediately press and hold the volume down (-) button until the message ‘Reset’ is
shown on the display (Fig. 30).
The unit has now been reset to the default factory settings.
Now do the same for the other unit.
Default settings
Parent unit
Loudspeaker volume: 1
Microphone sensitivity: 3
Sound alert: on
Temperature alert: on
‘Temperature low’ alert: 14°C
‘Temperature high’ alert: 30°C
,
,
-
-
-
-
-
-
ENGLISH 11

Baby unit
Loudspeaker volume: 3
Nightlight: off
Lullaby: 1
Menu options
Most functions can be operated on both the baby unit and the parent unit, but there are some
functions that can only be set via the menu options available on the parent unit.
Menu operation - general explanation
1 Press the MENU button to open the menu (Fig. 31).
The rst menu option appears on the display.
2 Use the – and + buttons to select the desired menu option (Fig. 32).
3 Press the OK button to conrm your choice (Fig. 33).
4 Use the + and - buttons to select the desired setting.
5 Press the OK button to conrm your choice.
Jappears on the display.
6 Press the MENU button again to exit the menu (Fig. 31).
Note: Always press the MENU button, the – and + buttons and the OK button briey. If you press the
buttons too long, they do not work.
Nightlight on/off
1 Select Kor L by pressing the – and + buttons. Conrm the
selected setting by pressing the OK button.
Playing lullabies
To play or stop a lullaby:
1 Select |K by pressing the – and + buttons and conrm by pressing the OK
button.
2 Select :to play the last played lullaby again or <| to stop playing.
Conrm by pressing the OK button.
To select a different lullaby:
1 Select |K by pressing the – and + buttons and conrm by pressing the OK
button.
2 Select ~ by pressing the – and + buttons and conrm by pressing the OK
button.
3 Select the desired lullaby by pressing the – and + buttons and conrm by pressing the OK
button.
Adjusting microphone sensitivity
You can set the microphone sensitivity of the baby unit to the desired level.You can only change the
microphone sensitivity when a connection between the baby unit and the parent unit has been
established, i.e. when the LINK light on the parent unit lights up green continuously.
1 Select ZR by pressing the – and + buttons and conrm by pressing the OK
button.
-
-
-
,
,
ENGLISH12

2 Select the desired microphone sensitivity level for the baby unit by pressing the – and +
buttons and conrm by pressing the OK button.
one light on = minimum sensitivity level
all lights on = maximum sensitivity level
Note:When the microphone sensitivity of the baby unit is set to a high level, it picks up more sounds and
therefore transmits more often.As a result, the units consume more power.
Sound alert on/off
If the sound alert is switched on, the parent unit beeps as soon as the fth sound level light lights up
blue while the volume is switched off.
1 Select X by pressing the – and + buttons and conrm by pressing the OK
button.
2 Select Cor V and conrm by pressing the OK button.
Setting room temperature range
You can set the temperature range (minimum and maximum temperature) for your baby’s room.
1 Select B– – ° by pressing the – and + buttons and conrm by pressing
the OK button.
Nappears on the display.
2 Conrm by pressing the OK button.
3 Set the desired minimum temperature by pressing the – and + buttons and conrm by
pressing the OK button.
4 Set the desired maximum temperature by pressing the – and + buttons and conrm by
pressing the OK button.
Note:When the maximum temperature selected is lower than the room temperature, the unit consumes
more power because the display is on continuously.This is also the case when the minimum temperature
set is higher than the room temperature.
Temperature alert on/off
If the temperature alert is switched on, the parent unit beeps if the actual room temperature
exceeds the set maximum temperature or drops below the set minimum temperature. If no
minimum and maximum temperatures have been set, the temperature alert goes off when the
room temperature drops below 7°C or rises above 33°C.
1 Select B– – ° by pressing the – and + buttons and conrm by pressing
the OK button.
2 Select M by pressing the – and + buttons and conrm by pressing the OK
button.
3 Select Cor V and conrm by pressing the OK button.
Cleaning and maintenance
Do not immerse the parent unit and the baby unit in water and do not clean them under the tap.
Do not use a cleaning spray and/or liquid cleaners.
1 Unplug the baby unit if it is connected to the mains and take the parent unit out of the
charger.
2 Clean the parent unit and the baby unit with a damp cloth.
,
,
,
ENGLISH 13

Make sure the parent unit is dry before you put it back into the charger.
3 Clean the charger with a dry cloth.
Storage
You can use the travel pouch to store the baby monitor while you travel.
When you are not going to use the baby monitor for some time, remove the batteries and
store the parent unit, the baby unit, the adapter of the baby unit and the charger in the travel
pouch supplied.
Environment
Do not throw away the appliance with the normal household waste at the end of its life, but
hand it in at an ofcial collection point for recycling. By doing this, you help to preserve the
environment (Fig. 34).
Batteries contain substances that may pollute the environment. Do not throw
away batteries with the normal household waste, but hand them in at an ofcial collection
point. Always remove the batteries before you discard and hand in the appliance at an ofcial
collection point.
Guarantee and service
If you need information or if you have a problem, please visit the Philips website at www.philips.com
or contact the Philips Customer Care Centre in your country (you nd its phone number in the
worldwide guarantee leaet). If there is no Customer Care Centre in your country, go to your local
Philips dealer or contact the Service Department of Philips Domestic appliances and Personal Care
BV.
Frequently asked questions
This chapter lists the questions most frequently asked about the appliance. If you cannot nd the
answer to your question, contact the Customer Care Centre in your country.
Question Answer
Why don’t the ON light
of the baby unit and the
LINK light of the parent
unit come on when I
press the on/off buttons
of the units?
Perhaps the batteries of the parent unit are empty and the parent
unit is not in the plugged-in charger. Put the adapter of the charger in
the wall socket and place the parent unit in the charger.Then press
the on/off button to establish connection with the baby unit.
Perhaps the batteries of the baby unit are empty and the baby unit is
not connected to the mains. Replace the batteries or put the small
plug in the baby unit and put the adapter in a wall socket.Then press
the on/off button to establish connection with the parent unit.
The baby unit and the parent unit may be out of range of each other.
Move the parent unit closer to the baby unit, but not closer than
1 metre/3 feet.
If the LINK light on the parent unit still does not start to ash, use
the reset function to reset the units to their default settings.
,
,
,
,
ENGLISH14

Question Answer
Why does the LINK light
on the parent unit ash
red and why is the
message (
O) shown
on the display?
The baby unit and the parent unit are out of range of each other.
Move the parent unit closer to the baby unit.
Why does the LINK light
on the parent unit ash
red?
The batteries of the baby unit are running low. Replace the batteries
or connect the baby unit to the mains (see chapter ‘Preparing for
use’).
Why does the parent unit
beep? If the parent unit beeps while the LINK light ashes red and the message ( O) is shown on the display, the connection
with the baby unit is lost. Move the parent unit closer to the baby
unit.
If the parent unit beeps and the battery symbol on the display is
empty, the batteries are running low. Recharge the batteries.
If you have switched off the volume while the sound alert is on, the
parent unit beeps whenever the fth sound level light lights up blue
because the baby unit has picked up a sound.
If you have set the room temperature on the parent unit and the
temperature alert is on, the parent unit beeps when the temperature
drops below the set level or below 7°C or when the temperature
rises above the set level or above 33°C.
Why does the appliance
produce a high-pitched
noise?
The units may be too close to each other. Make sure the parent unit
and the baby unit are at least 1 metre/3 feet away from each other.
The volume of the parent unit may be set too high. Decrease the
volume of the parent unit.
Why don’t I hear a sound/
Why can’t I hear my baby
cry?
The volume of the parent unit may be set too low or may be
switched off. Increase the volume of the parent unit.
The microphone sensitivity level of the baby unit may be set too low.
Set the microphone sensitivity level to a higher level in the menu of
the parent unit.
The baby unit and the parent unit may be out of range of each other.
Reduce the distance between the units.
Why does the parent unit
react too quickly to other
sounds?
The baby unit also picks up other sounds than those of your
baby. Move the baby unit closer to the baby (but observe the
minimum distance of 1 metre/3 feet).
The microphone sensitivity level of the baby unit may be set too high.
Decrease the microphone sensitivity level in the menu of the parent
unit.
Why does the parent unit
react slowly to the baby’s
crying?
The microphone sensitivity level of the baby unit may be set too low.
Increase the microphone sensitivity level of in the menu of the parent
unit.
ENGLISH 15

Question Answer
Why do the batteries of
the baby unit run low
quickly?
The microphone sensitivity level of the baby unit may be set too high,
which causes the baby unit to transmit more often. Decrease the
microphone sensitivity level in the menu of the parent unit.
The volume on the baby unit may be set too high, which causes the
baby unit to consume a lot of energy. Decrease the volume of the
baby unit.
You may have set a maximum room temperature that is lower than
the actual room temperature or a minimum room temperature that
is higher than the actual room temperature.This causes the display to
be lit all the time, which results in higher power consumption and
batteries that run low quickly.
Perhaps you have switched on the nightlight. If you want to use the
nightlight, we advise you to run the baby unit on mains power.
Why does the charging
time of the parent unit
exceed 8 hours?
The parent unit may be switched on during charging. Switch off the
parent unit during charging.
The specied operating
range of the baby monitor
is 300 metres/900 feet.
Why does my baby
monitor manage a much
smaller distance than that?
The specied range is only valid outdoors in open air. Inside your
house, the operating range is limited by the number type of walls
and/or ceilings in between. Inside the house, the operating range is
up to 50 metres/150 feet.
Why is the
connection lost every
now and then? Why are
there sound interruptions?
The baby unit and the parent unit are probably close to the outer
limits of the operating range.Try a different location or decrease the
distance between the units. Please note that it takes about 30
seconds each time before a connection between the units is
established.
What happens during a
power failure? If the parent unit is sufciently charged, it continues to operate during
a power failure, both inside and outside the charger. If there are
batteries in the baby unit, it automatically switches to battery
operation in case of power failure.
Is my baby monitor
secure from
eavesdropping and
interference?
The DECT technology of this baby monitor guarantees no
interference from other equipment and no eavesdropping.
Some buttons do not
seem to work when I
press them.What do I do
wrong?
You should press all buttons (except the on/off buttons and the TALK
button) briey. If you press them too long, they do not work.
The operating time of the
parent unit is supposed to
be at least 24 hours.Why
is the operating time of
my parent unit shorter?
When the parent unit batteries have been charged for the rst time,
the operating time is less than 24 hours.The batteries only
reach their full capacity after you have charged and discharged
them at least four times.
ENGLISH16

Question Answer
The volume of the parent unit may be set too high, which causes the
parent unit to consume a lot of energy. Decrease the volume of the
parent unit
The microphone sensitivity level of the baby unit may be set too high,
which causes the parent unit to consume a lot of energy. Decrease
the microphone sensitivity level in the menu of the parent unit.
Why doesn’t battery
symbol appear on the
display of the parent unit
when I start to recharge
the parent unit?
It may take a few minutes before the battery symbol appears on the
display of the parent unit when you charge the parent for the rst
time or after a long period of disuse.
ENGLISH 17

18
Introduktion
Philips/Avent sætter en ære i at producere pålidelige produkter, der kan give forældre den tryghed,
de har brug for. Denne Philips/Avent-babyalarm hjælper dig døgnet rundt ved at sikre, at du altid kan
høre din baby klart og tydeligt uden forstyrrende støj. DECT-teknologien garanterer, at der ikke
forekommer interferens fra andre trådløse apparater, og den giver et klart signal mellem babyenhed
og forældreenhed.

ABabyenhed
1 On/Off-knap 3
2 Temperatursensor
3 Kontrollampe for ON (tændt)
4 Lydstyrke +/– knapper
5 PAGE-tast
6 Display
7 Natlys
8 Play/stop-tast E
9 Vuggevise-tast K
10 Natlys Q
11 Mikrofon
12 Adapter
13 Lille stik
14 Låg til batterirum
15 Lille strømstik
16 Batterirum
B Forældreenhed
1 Lydniveau med lys
2 Display
3 TALK-tast
4 MENU-tast
5 On/Off-knap 3
6 LINK-lysindikator
7 Åbning til bælteclips og halsstrop
8 Lydstyrke +/– knapper
9 OK-tast
10 Mikrofon
11 Højttaler
12 Batterirum
13 Bælteclips
14 Låg til batterirum
15 Halsstrop
16 Adapter
17 Oplader
18 POWER-lysindikator
CDisplay
1 Ñ° Angivelse af rumtemperatur
2 QNatlys-indikator
3 KVuggevisesymbol
4 TBatterisymbol
5 oLydstyrkeindikation
6 RIndikator for mikrofonfølsomhed
7 UHøjere rumtemperatur end angivet i menuen
DANSK

8 ILavere rumtemperatur end angivet i menuen
9 O ‘No connection between units’ meddelelse (ingen forbindelse mellem
enhederne)
10 { ‘Volume level’ meddelelse (lydstyrke)
11 SMeddelelse, når vuggevisen afbrydes
DRejseetui
Vigtigt
Læs denne brugsvejledning omhyggeligt igennem, inden apparatet tages i brug, og gem den til
eventuelt senere brug.
Denne babyalarm er beregnet som et hjælpemiddel. Den kan aldrig erstatte den ansvarlige og
korrekte forældrekontakt og -overvågning og må ikke bruges som sådan.
Kontrollér, om den indikerede netspænding på adapteren til babyenheden og til opladeren
svarer til den lokale netspænding, før du tilslutter apparatet.
Apparatet skal opbevares ved temperaturer mellem 10° C og 40° C.
Apparatet kan tilsluttes netspændinger mellem 220 og 240V.
Udsæt ikke babyalarmen for meget høje eller meget lave temperaturer eller direkte sollys.
Ledningen skal altid være uden for barnets rækkevidde (mindst 1 meter væk).
Anbring ikke babyenheden i barnets seng eller kravlegård.
Dæk ikke babyalarmen til med håndklæder, tæpper el. lign.
Babyalarmen (eller dele af den) må aldrig kommes ned i vand eller andre væsker.
Babyalarmen må ikke bruges i fugtige omgivelser eller tæt ved vand.
Forsøg aldrig at åbne baby- eller forældreenhed udover batterirummene, da det kan give
risiko for elektrisk stød.
Når babyenheden tilsluttes lysnettet, må det kun ske med den medfølgende adapter.
Benyt kun den medfølgende oplader til opladning af forældreenheden.
Begge adaptere indeholder en transformer, som aldrig må klippes af eller udskiftes med andre
stik, da dette kan være meget risikabelt.
Hvis adapteren til babyenheden beskadiges, skal den altid udskiftes med en original adapter af
samme type for at undgå enhver risiko.
Hvis opladeren eller opladerens adapter beskadiges, skal opladeren altid udskiftes med en
original oplader af samme type for at undgå enhver risiko.
Benyt altid den korrekte type ikke-genopladelige batterier i babyenheden for at undgå
eksplosionsfare. Benyt altid den korrekte type genopladelige batterier til forældreenheden.
Da konstant transmission ikke er tilladt, vil du kun kunne høre dit barn, når det laver lyde.
Elektromagnetiske felter (EMF)
Dette Philips/Avent-apparat overholder alle standarder for elektromagnetiske felter (EMF). Ved
korrekt anvendelse i overensstemmelse med instruktionerne i denne brugsvejleding er apparatet
sikkert at anvende, ifølge den videnskabelige viden, der er tilgængelig i dag.
Klargøring
Babyenheden
Babyenheden kan enten bruges via lysnettet eller med batterier. Selvom enheden får strøm fra
lysnettet, anbefaler vi, at du sætter batterier i. Dette garanterer automatisk back-up i tilfælde af
strømsvigt.
Brug via lysnet
1 Sæt det lille stik i babyenheden og sæt adapteren i en stikkontakt (g. 2).
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
DANSK 19

Brug med batterier
Babyenheden benytter re 1,5 V batterier af typen R6 AA (medfølger ikke). Vi anbefaler Philips LR6
PowerLife-batterier.
Sørg for, at både enheden og dine hænder er tørre, når batterierne isættes.
1 Drej dækslet til batterirummet til venstre ( Á OPEN) med håndaden. (g. 3)
2 Tag dækslet af.
3 Isæt re 1,5 V R6 AA batterier (g. 4).
Anbring to batterier oven på hinanden, og sørg for, at polerne (+ og –) vender den rigtige vej.
4 Sæt dækslet til batterirummet tilbage på plads, og luk det ved at dreje det til højre (CLOSE ª)
med håndaden. (g. 5)
Bemærk: Når batterierne er ved at løbe tør for strøm, ses batterisymbolet i displayet.
Forældreenhed
Brug med batterier
Forældreenheden benytter to genopladelige 1,2-volt AAA NiMh-batterier, der leveres sammen med
apparatet.
Sørg for, at både enheden og dine hænder er tørre, når batterierne isættes.
1 Skub batterirummets dæksel nedad for at tage det af (g. 6).
2 Sæt de to genopladelige batterier i (g. 7).
Sørg for, at batteriernes poler (+ og -) vender den rigtige vej.
3 Skub dækslet til batterirummet tilbage på bagsiden af forældreenheden, indtil det fastlåses
(‘klik’) (g. 8).
4 Sæt opladerens adapter i en stikkontakt, og anbring forældreenheden i opladeren (g. 9).
Opladerens POWER-indikator lyser.
5 Lad forældreenheden stå i opladeren, indtil batterierne er fuldt opladede.
Når apparatet oplades første gang eller efter en længere periode uden at have

En fuld opladning tager normalt 8 timer men længere tid, hvis forældrenheden er tændt under
opladningen. Sluk derfor altid for forældreenheden under opladning, for at gøre
opladningstiden så kort som muligt.
Opladerens POWER-indikator bliver ved med at lyse, selv når batterierne er fuldt opladede.
Når batterierne er fuldt opladede, kan forældreenheden bruges trådløst i mindst 24 timer.
Bemærk: Brugstiden på 24 timer er baseret på den antagelse, at babyenheden sender 25% af tiden og
er i standby-tilstand resten af tiden (når babyen ikke giver lyd fra sig).
Bemærk: Efter første opladning af batterierne i forældreenheden, er brugstiden mindre end 24 timer.
Batterierne når først op på deres fulde kapacitet, når de er blevet opladet og aadet re gange.
Bemærk: Når batterisymbolet i displayet er tomt, og forældreenheden bipper, er batterierne ved at løbe
tør for strøm. Sæt forældreenheden i opladeren.
Bemærk: Når forældreenheden ikke står i opladeren, aades batterierne gradvist, selvom
forældreenheden er slukket.
Brug via lysnet
1 Sørg for, at de genopladelige batterier er sat i forældreenheden.
2 Sæt opladerens adapter i en stikkontakt, og anbring forældreenheden i opladeren (g. 9).
,
,
,
,
,
,
,
DANSK20