PHILIPS Respironics ComfortGel Assembly instructions

ComfortGel Full and ComfortFull 2 mask
patient and clinician fitting guide
Sizing the mask
Preparing the mask for fitting
Use either the plastic sizing gauge or the
gauge that is part of the mask package to
determine the appropriate mask size.
Place the sizing gauge over the nose and
mouth.The mouth should be open slightly.
Choose the smallest size mask cushion that
is wider than the mouth and long enough to
extend beyond the lower lip.
Loosen the straps on the headgear
using the EZPeel tabs.
Gently squeeze the sides of the
StabilitySelector and slide the arm
upward to set the forehead support
arm to its highest position.
Next, disconnect the headgear by
releasing one or both ball-and-socket
Quick Clip(s) from the faceplate
socket(s).
Making initial adjustments
Make initial adjustments while sitting.
1. Place the mask cushion against
the face by first setting the base
of the cushion under the lower lip
then rolling the cushion up over
the nose. Be sure the mouth
remains slightly open.
3. For easy attachment of a Quick Clip,
use the finger as a guide to find the
position of the socket and press the
clip into the socket.
2. Pull the headgear over the head.

Making final adjustments
6. Be sure that the top and bottom straps
of the headgear are parallel and the
back headgear panel lies flat against
the head.
Correct fit:
The headgear should fit snug but
comfortably.The mask should be
loose enough to allow a finger to
run under the headgear straps.
Do not over-tighten the headgear.
Incorrect fit:
If the skin bulges around the mask or
there are red marks or impressions on
the skin, loosen the headgear straps.
Make final adjustments while lying
down. If the forehead pad does not
rest lightly against the forehead,
adjust the upper headgear straps.
If necessary, adjust the bottom
straps so that the mask is snug
but comfortable against the face.
Attach the tubing to the swivel elbow
and turn on the air.
Making initial adjustments (continued)
4. Adjust the top headgear straps by
using the EZPeel tabs. Be sure that
they are tightened evenly and the
forehead pad is lightly touching
the forehead.
5. Adjust the bottom headgear straps
using the EZPeel tabs until they
are even and the mask is gently
sitting on the face.The mask
should not feel tight.

Identifying leaks
Turn on the PAP and gradually raise the
pressure to the prescribed level.Turn the
head from side to side while lying on the
bed and with the mouth open slightly.
Identify areas of leak that may prevent
the ability to sleep.
Adjusting for leaks
2. Adjust the StabilitySelector to correct for any leaks.
This is a critical step in the fitting process.
Problem: Leaks around the nose or into the eyes.
Solution: Adjust the StabilitySelector to a lower position by gently squeezing the arms of
the StabilitySelector and sliding it downward to a lower position.This will bring
the top of the cushion closer to the face. If necessary, re-seat the mask again.
In the event of leaks, follow these recommended methods to obtain a better seal:
1. Re-seat the mask. Pull the mask directly away from the face and gently set it back into
place.This allows the cushion and flap to create a new seal on the face.
Problem: Leaks around or below the mouth.
Solution: Adjust the StabilitySelector to a higher position by gently squeezing the arms of
the StabilitySelector and sliding it upward to a higher position.This will bring the
bottom of the cushion closer to the face. If necessary, re-seat the mask again.
3. Tighten the headgear. If leaks are still present, apply pressure with the fingers directly
to the mask in the location of the leak. If this eliminates the leak, tighten the headgear
straps closest to the leak to accommodate the seal. Do not over-tighten the headgear.
Note: Excessive tightening of the headgear may cause unnecessary discomfort and actually
cause leaks. Remember, not all leaks need to be corrected.

Removing the mask
To remove the mask, disconnect one or both
ball-and-socket Quick Clip(s). Grab the bottom
of the headgear on the back of the head and
pull the mask gently up and over the head.
Use the Quick Clip to remove the mask and
maintain mask and headgear adjustments
from day-to-day.
Removing the ComfortGel Full cushion and flap
Attaching the ComfortGel Full cushion
2. Remove the cushion and flap. 3. Separate the cushion from the flap.
1. Lift up on the tabs at the
bottom of the mask’s
integrated retaining ring.
To remove the cushion and flap with the integrated retaining ring:
1. Place the gel cushion on the
ledge of the faceplate.
2. Place the flap with its
integrated retaining ring
down over the gel cushion.
4. Gently tug on the cushion and
the ring to make sure all the
parts are securely in place.
3. Press firmly on the retaining
ring until all sides click
into place.
© 2009 Koninklijke Philips Electronics N.V. All rights are reserved.
Philips Healthcare reserves the right to make changes in specifications and/or to
discontinue any product at any time without notice or obligation and will not be liable
for any consequences resulting from the use of this publication.
CAUTION: US federal law restricts these devices to sale by or on the order of a
physician.
Hoech JJ 11/03/09 MCI 4102971 PN 1050785
Philips Healthcare is part of Royal Philips Electronics
Respironics Asia Pacific
[phone]
Respironics Australia
[phone]
Respironics Europe, Middle East,Africa
[phone]
Respironics United Kingdom
[phone]
Philips Respironics
1010 Murry Ridge Lane
Murrysville, PA 15668
Customer Service
[phone]
800 345 6443 (toll free, US only)
www.philips.com/respironics
Please visit www.philips.com/respironics
Respironics, ComfortFull, ComfortGel, EZPeel, Quick Clip and StabilitySelector are trademarks of Respironics, Inc. and its affiliates, all rights reserved.