Philips HF3505 User manual

Always here to help you
User manual
Register your product and get support at
www.philips.com/welcome
HF3505
HF3500

1

HF3505, HF3500
ENGLISH 4
DANSK 11
DEUTSCH 18
ESPAÑOL 25
SUOMI 32
FRANÇAIS 39
ITALIANO 46
NEDERLANDS 53
NORSK 60
PORTUGUÊS 67
 74
SVENSKA 81

4
Introduction
Congratulations on your purchase and welcome to Philips!
To fully benet from the support that Philips offers, register your product
at www.philips.com/welcome.
The Philips Wake-up Light helps you wake up more pleasantly.The light
intensity of the lamp gradually increases to the set level in the 30 minutes
before the set wake-up time.The light gently prepares your body for waking
up at the set time. To make waking up an even more pleasant experience,
you can use natural wake-up sounds or the FM radio (HF3505 only).
The effects of theWake-up Light
The Philips Wake-up Light gently prepares your body for waking up
during the last half hour of sleep. In the early morning hours our eyes are
more sensitive to light than when we are awake. During that period the
relatively low light levels of a simulated natural sunrise prepare our body
for waking up and getting alert. People who use the Wake-up Light wake
up more easily, have a better overall mood in the morning and feel more
energetic. Because the sensitivity to light differs per person, you can set
the light intensity of your Wake-up Light to a level that matches your light
sensitivity for an optimal start of the day.
For more information about the Wake-up Light, see www.philips.com.
General description (Fig. 1)
1 Wake up light
2 Display brightness
3 Volume lower (HF3505 only)
4 Volume higher (HF3505 only)
5 Radio (HF3505 only)
6 FM scan (HF3505 only)
7 Light on/off
8 Alarm on/off
9 Clock time
10 Alarm sound types (HF3505 only)
11 Antenna (HF3505 only)
Preparing for use
Setting the clock
1 Put the plug in the wall socket.
ENGLISH

2 When plugging in, the clock time will automatically start blinking.
,If the clock time does not start blinking, press the clock button on
the side of the appliance.
,The clock icon appears on the display.
3 Press the + or - button to set the hour and minutes.
Note:You can only do this when you are in the set clock time and when the
time indication ashes. If this is not the case, press the clock button again,
you are now in the set clock time.
4 PresstheClockbuttontoconrm.
You can also wait for 5 seconds before the clock is xed.
Note: Every time you remove the plug from the wall socket, clock time setting
is lost.
Using the appliance
Functions
Below you can nd a list of all functions that can be set in this appliance:
- Clock time
- Time format
- Alarm time
- Alarm sounds (HF3505 only)
- FM (HF3505 only)
- Light level
- Display brightness
You can set these functions in the following way:
ENGLISH 5

Using the light
You can use the appliance as a bedside lamp.
1 To switch on the light, press the lamp on/off button.
,The light icon is shown in the display and the current light level
10 appears.
2 Press the + and - buttons to select a light intensity.
You can choose a light intensity between 1 and 10.
Note: The light intensity you have selected is automatically set as the light
intensity level for the alarm as well.
3 To switch off the lamp, press the lamp on/off button again.
Note: The light level can be adjusted when light is on/off.
Setting time format
Switching between 24h and 12h time mode.
1 Press the Clock button for > 2 seconds.
When the 12h mode is active, PM or AM will be shown in display.
Note: To switch to the 24h mode, press the Clock button again for >2 seconds.
Setting the alarm
When you set the alarm, you choose an alarm time and (only in case of
HF3505) the type of sound you want to wake up to. The alarm is activated
when the alarm symbol is visible on the display.The light intensity slowly
increases to the selected level during the last 30 minutes before the set
alarm time.The sound slowly increases to the selected level after the set
alarm time.
HF3505 only:
Light level range is 1-10, volume level range is 1-10. It is not possible to
switch these functions off.
HF3500 only:
Light level range is 1-10 and there is no volume control for the type of the
appliance. The alarm sound volume is xed.
ENGLISH6

1 Press the alarm button to switch on the alarm.
,Thetimeindicationofthealarmtimeashes.
,Alarm icon appears on display.
2 Press the + or - buttons to select the time.
Note: You can only do this when the time indication ashes. If this is not the
case, press the alarm button again to enter the alarm time mode.
Tip: Press the + or - button >2 seconds to speed up the digit change.
3 PresstheAlarmbuttontoconrmorwaitfor5seconds.
Note: The alarm icon is shown in the display to indicate the alarm is ON.
The alarm time is now set.
Switching off the alarm
When the alarm goes off, you can switch off the alarm by pressing on the
alarm button.The alarm will go off again the next day.
When you want to switch off the alarm for the next day, or before the
alarm goes off, press the alarm button again.
Note: The alarm icon disappears from the display.
Note: The lamp stays on to light your room. You can switch off the lamp by
pressing the light on/off button.
Note: The alarm (sound and/or light) automatically switches off after
90 minutes.
ENGLISH 7

Setting the alarm sound (HF3505 only)
You can choose one of the following sounds by switching the function from:
- Sound I
- Sound II
- Radio
Note: When switching to a new alarm sound or radio, a preview of that sound/
radio will be played for 5 seconds.
Snoozing
1 Tap on top of the appliance to snooze 9 minutes.
,The lamp continues to be on at the selected intensity level, but
the alarm sound stops.After 9 minutes, the wake-up sound is
automatically played again.
Note: The 9-minute snooze time is xed. This time cannot be adjusted.
Radio/volume (HF3505 only)
Tip: Fully unwind the antenna to use the radio function.
1 To switch on the radio, press the radio on/off button.
,The radio icon appears in the display.
ENGLISH8

2 To select the desired radio frequency, press the « and » buttons.
Tip: To scan radio frequencies automatically, press and hold the « or » button
for approx. 2 seconds.
Tip: To make sure you get a good radio signal, fully unwind the antenna and
move it around until you have found a position at which reception is best.
Note: The current radio frequency is shown in the display for 5 seconds, before
clock time is shown again.
3 To switch off the radio, press the radio on/off button again.
Volume
1 To set the volume, press the volume increase or decrease button.
You can choose a volume level between 1 and 10.
Note:The volume level you have selected is automatically set as the volume
level for the alarm as well.
Setting the display brightness
1 Press the Display brightness button to adjust the display brightness.
The brightness of the display will change from high-medium-low-very low.
Demo mode
If you want a quick demonstration (90 seconds) of the gradually increasing
light intensity and sound level, switch on the test function of the appliance.
1 Press and hold the alarm button for at least 3 seconds.
2 The appliance starts the demonstration of the alarm.
3 To switch off the demonstration, press and hold the previously
pressed alarm button for 3 seconds again.
ENGLISH 9

Cleaning and maintenance
Never use scouring pads, abrasive cleaning agents or aggressive liquids
such as petrol or acetone to clean the appliance.
Regularly remove dust from the outside of the appliance with a dry cloth.
1 Unplug the appliance before you clean it.
2 Clean the outside of the appliance with a dry cloth.
Do not let water run into the appliance or spill water onto the appliance.
Replacement
This appliance does not contain any serviceable parts.
Environment
- Do not throw away the appliance with the normal household waste
at the end of its life, but hand it in at an ofcial collection point for
recycling. By doing this, you help to preserve the environment.
ENGLISH10