Philips AJ3112/12 User manual

Clock Radio
Register your product and get support at
www.philips.com/welcome
User manual
AJ3112

SAFETY INFORMATION
• Install the unit near the AC outlet and where the AC plug can be easily
reached.
• Where the MAINS plug is used as the disconnect device, the discon-
nect device shall remain readily operable.
• Place the set on a hard and flat surface so that the system does not tilt.
• If you do not intend to use the set for a long time, withdraw the
power plug from the wall outlet. In addition to this, it is advisable to
remove the battery from the clock radio.This will prevent any danger
of leakage and the clock radio will not be damaged.
• Do not expose the set, batteries to humidity, rain, sand or excessive
heat caused by heating equipment or direct sunlight.
• The apparatus shall not be exposed to dripping or splashing.
• Adequate ventilation with a minimum gap of 15cm between the ventila-
tion holes and surrounding surfaces is necessary to prevent heat build-up.
• The ventilation should not be impeded by covering the ventilation
openings with items, such as newspapers, table-cloths, curtains, etc..
• No objects filled with liquids, such as vases, shall be placed on the apparatus.
• No naked flame sources, such as lighted candles, should be placed on
the apparatus.
• To clean the set, use a soft, slightly dampened chamois leather. Do not
use any cleaning agents containing alcohol, ammonia, benzene or abra-
sives as these may harm the housing.
• Battery shall not be exposed to excessive heat such as sunshine, fire or
the like.
CAUTION
Use of controls or adjustments or performance of proce-
dures other than herein may result in unsafe operation.
This set complies with the radio interference requirements
of the European Union.
English

Notes for battery disposal
Your product contains batteries covered by the European Directive
2006/66/EC, which cannot be disposed of with normal household waste.
Please inform yourself about the local rules on separate collection of bat-
teries.The correct disposal of batteries helps prevent potentially negative
consequences on the environment and human health.
Environmental information
We have reduced packaging to the minimum for easy separation into two
materials: paper and cardboard.
Your set consists of materials which can be recycled if disassembled by a
specialized company. Please observe local regulations on the disposal of
packing materials and old equipment.
Disposal of your old product
Your product is designed and manufactured with high quality materials and com-
ponents, which can be recycled and reused.
When this crossed-out wheeled bin symbol is attached to a product it
means the product is covered by the European Directive 2002/96/EC.
Please inform yourself about the local separate collection system
for electrical and electronic products.
Please act according to your local rules and do not dispose of your old
products with your normal household waste.The correct disposal of your
old product will help prevent potential negative consequences for the envi-
ronment and human health.
Class II equipment symbol
This symbol indicates that the unit has a double insulation system g

Congratulations on your purchase and welcome to Philips!
To fully benefit from the support that Philips offers,
register your product at www.philips.com/welcome.
3
4
1
#%^ $
5
9
0
678
2
!
@

CONTROLS
1
DISPLAY - shows the clock/ alarm time and status of the set
2ALARM indicator -
lights up when alarm is activated
3Frequency indicator - shows the radio frequency of your selected
waveband
4REPEAT ALARM /
SLEEP OFF
- switches off the active alarm for a 8-9 minute period
- switches off the sleep function
5CLOCK - sets the clock time
6SLEEP
- activates the radio for sleep function
- adjusts the sleep period
7
ALARM RESET - stops the active alarm for 12 hours
8
ALARM - sets the alarm function
9
RADIO / ALARM
RADIO ON: switches on the radio
RADIO OFF: switches off the radio/alarm
ALARM - RADIO: activates the radio for alarm
ALARM - BUZZ: activates the buzzer for alarm
0
SET TIME HR / MIN
- adjusts the hours / minutes for clock / alarm / sleep time
!Power cord -
connects to wall outlet
@Pigtail - improve FM reception
#VOLUME - adjusts the sound level
$
Battery door - opens to store a 9 volts 6F22 battery (not included) for
clock memory backup.
%
FM/AM (MW) - selects FM/AM (MW) waveband
^TUNING - tunes to radio stations

INSTALLATION
POWER SUPPLY
1
Check if the power supply, as shown on the type plate located on
the bottom of the set, corresponds to your local power supply. If it
does not, consult your dealer or service center.
2 Connect the plug to the wall outlet.
3 To disconnect the set from the power supply completely,
remove the plug from the wall outlet.
CLOCK MEMORY BACKUP
The clock memory backup allows your alarm and clock time settings to be
stored for up to a day when there is a power interruption e.g. power fail-
ure.The complete clock radio and display illumination will be switched off.
As soon as the power supply returns, the display will indicate the correct
time.
1 Remove the battery door to insert a 9 volts 6F22 type battery (not
included) for backup.
2 Replace the battery door.
NOTE: If no backup battery is installed or the power interruption is
prolonged, you will need to set the clock and alarm times
again. Batteries contain chemical substances so they should
be disposed of properly.

RADIO
You can use this set solely as a radio!
1
Adjust RADIO / ALARM to RADIO ON to switch on the radio.
2 Select your waveband by adjusting the FM/AM (MW) switch .
3
Adjust TUNING to tune to your desired station .
4
Turn the VOLUME control to adjust the volume level .
5
Adjust RADIO / ALARM to OFF to switch off the radio.
To improve reception:
FM: Extend and position the pigtail fully to obtain optimal recep-
tion.
AM (MW): uses a built-in antenna inside the set. Direct the antenna
by adjusting the position of your set
.
SETTING THE CLOCK / ALARM TIME
The time is displayed using the 12-hour clock.
1 Hold down CLOCK or ALARM.
2 Press HR or MIN repeatedly, or hold down HR or MIN to adjust
minute and/or hour.
3 Release CLOCK or ALARM and HR or MIN when you reach the
correct setting.
™
The set clock time will show on the display and start to run.
SELECTING THE ALARM MODE
To use the alarm, you must set the alarm time first.You can choose from
two different alarm modes to wake you up: by radio or buzzer.
1 Select your choice of alarm mode by adjusting RADIO / ALARM to
RADIO or BUZZ .
™
The alarm indicator (AL) will light up.

Helpful Hint:
• If you have selected the radio mode, make sure you have adjusted the
volume loud enough to wake you.
• The buzzer is set at a fixed volume and cannot be adjusted.
SWITCHING OFFTHE ALARM
There are three ways of switching off the alarm. Unless you cancel the
alarm completely, the 12 hour alarm reset option will be automatically
selected after 1 hour and 59 minutes, from the time your alarm time first
goes off.
12 HOUR ALARM RESET
If you want the alarm mode to be stopped immediately but also wish to
retain the same alarm setting for the following day:
• Press ALARM RESET during the alarm call.
™
The alarm indicator (AL) will remain on.
CANCELING THE ALARM COMPLETELY
To cancel the set alarm time before it goes off, or during the alarm call:
• Adjust RADIO / ALARM to OFF position.
™
The alarm indicator (AL) will light off.
REPEAT ALARM
This repeats your alarm call at 9-minute intervals.
1 During the alarm call, press REPEAT ALARM /
SLEEP OFF
.
™
The alarm indicator (AL) will remain on.

SLEEP
This set has a built-in timer which enables the set to be automatically
switched off during radio playback after a set period of time.This allows
you to lie back, listen and fall asleep.The maximum sleep time is 1 hour
and 59 minutes.
Setting SLEEP
1 Set RADIO / ALARM to OFF position.
2 Set the sleep time to activate sleep function by selecting on the follow-
ing ways:
• Simply press SLEEP to set your sleep time to 59 minutes.
• Hold down SLEEP , and press MIN repeatedly to adjust sleep time
from 59 minutes downward.
• Hold down SLEEP and press HR to get one more hour sleep time
(1:59)
™
To cancel sleep, press REPEAT ALARM /
SLEEP OFF
.
Specifications
AC Power.......................................................220 V / 60 Hz
Power Consumption
Active.........................................................................3.5 W
Standby.......................................................................<2 W
Dimensions (w x d x h).......130.4 x 130 x 46.8 (mm)
Weight..........................................0.395 kg / 0.87 pounds

TROUBLESHOOTING
If a fault occurs, first check the points listed below before taking the set for repair.
If you are unable to remedy a problem by following these hints, consult your
dealer or service center.
WARNING: Under no circumstances should you try to repair the set
yourself, as this will invalidate the warranty. Do not open
the set as there is a risk of electric shock.
Problem
– Possible Cause
• Remedy
No sound/power
– Volume not adjusted
• Adjust the volume
Occasional crackling sound during FM broadcast
– Weak signal
•
Adjust the position of the Pigtail
Continuous crackling/hiss disturbance during AM (MW) broadcast
– Electrical interference from TV, computer, fluorescent lamp, etc.
• Move set away from other electrical equipment
The alarm does not function
– Alarm time not set and or alarm mode not selected
• Set the alarm time and / select alarm mode
– Volume too low for RADIO
• Adjust the volume
–
Radio alarm not adjusted to radio station
• Tune to a radio station