Philips SC463 User manual

SCD463
User manual 4
Mode d’emploi 16
Instrucciones de manejo 28
Bedienungsanleitung 40
Gebruiksaanwijzing 52
Istruzione per l’uso 64
Manual de utilização 76
Od  88
Bruksanvisning 100
Vejledning 112
Bruksanvisning 124
Käyttööhje 136
Kullanım talimatları 148
TR
SU
NO
DK
SV
GR
PR
IT
NL
DE
ES
FR
EN

2

3
B. Parent unit
A. Baby unit

A. Baby unit
A-1 On/Off button
A-2 DC 9V ——<<++power supply jack
A-3 AC power adapter
A-4 Power plug
A-5 Microphone
A-6 POWER light
A-7 Microphone sensitivity switch
A-8 Channel selection switch
A-9 Battery compartment cover
B. Parent Unit
B-1 Loudspeaker
B-2 LINK light
B-3 AC power adapter
B-4 Power plug
B-5 DC 9V ——<<++power supply jack
B-6 LINK alarm switch
B-7 Channel selection switch
B-8 ON/OFF switch / VOLUME control
B-9 POWER light
B-10 Battery compartment cover
C.What else you’ll need
– Coin (to open the battery compartment of the baby unit)
– Small, flat screwdriver (to set the channel selection switches)
– 4 x 1,5 V AA batteries for the baby unit
(optional, we recommend Philips Alkaline batteries)
– 4 x 1.5 V AA batteries for the parent unit
(optional, we recommend Philips Alkaline batteries)
EN Legend of functions
4

EN
5
3 Illustrations
4 Legend of functions
4 Baby unit
4 Parent unit
4 What else you need
5 Contents
6 Welcome
6 Safety information
7 Getting your baby monitor ready
7 Baby unit
7 Parent unit
8 Using your baby monitor
9 Other features
9 Avoiding interference
10 Adjusting microphone sensitivity
11 Switching the LINK alarm on and off
12 Troubleshooting
14 Frequently asked questions
14 Technical specifications
15 Important information
15 Environmental information
15 Maintenance
15 Need help?
Contents

Philips is dedicated to produce caring, reliable products to give
parents the reassurance they need.With this baby monitor you
can hear your baby from where ever you are in and around
your house.With sixteen different channels options you will
experience minimal interference.
Philips Baby Care, taking care together
Safety information
Please read this user manual carefully before using your baby
monitor and keep it for future reference.This baby monitor is
intended as an aid. It is not a substitute for responsible and
proper adult supervision and should not be used as such.
• Make sure the baby unit and adapter cable are always out of
reach of the baby (at least 1 meter / 3 feet away).
• Never place the baby unit inside the baby’s bed or playpen.
• Never cover the baby monitor (with a towel, blanket, etc.).
• Never use the baby monitor in moist places or close to
water.
• Check if the voltage indicated on the type plate of the
adapters (A-3, B-3) correspond to the local power voltage
before connecting to the AC power supply.
• Do not expose the baby monitor to extreme cold, heat or
light (e.g. direct sunlight).
• To prevent electric shock, do not open the inside of the baby
unit and parent unit (except for the battery compartment
cover).
• The antennas on both units are fixed; do not try to extend
them.
EN Welcome
6

EN
7
Baby unit
The baby unit can be mains or battery operated.
When batteries are installed, you have an automatic back up in
case of mains failure.
Mains operated use
1Connect the power adapter cord to the power supply jack
(DC 9V ——<<++- A-2) of the baby unit.
2Connect the AC power adapter (A-3) to a wall outlet.
➜The baby unit is now ready for mains operated use.
Battery operated use
1Remove the battery compartment cover (A-9) of the baby
unit, using a coin.
2Insert four 1,5V AA batteries, noting the + and –
configuration inside the battery compartment (batteries are
not supplied, we recommend Philips Alkaline batteries).
3Close the battery compartment cover (A-9), using a coin.
➜The baby unit is now ready for battery operated use.
Parent unit
The parent unit can be mains or battery operated.
When batteries are installed, you have an automatic back up in
case of mains failure.
Mains operated use
1Connect the power adapter cord to the power supply jack
(DC 9V ——<<++- B-5) of the parent unit.
2Connect the AC power adapter (B-3) to a wall outlet.
➜The parent unit is now ready for mains operated use.
Getting your baby monitor ready

Battery operated use
1Remove the battery compartment cover (B-10) of the parent
unit, by sliding down the cover.
2Insert four 1,5V AA batteries, noting the + and –
configuration inside the battery compartment (batteries are
not supplied, we recommend Philips Alkaline batteries)
3Slide the battery compartment cover (B-10) back in place
until it clicks in position
➜The parent unit is now ready for battery operated
use.
EN Getting your baby monitor ready
8
Using your baby monitor
1Position both units in the same room to test the connection.
Make sure the baby unit is at least 1 meter / 3 feet away from
the parent unit.
2Press the ON/OFF button (A-1) to switch on the baby unit.
> The POWER light (A-6) lights up green.
3Switch on the parent unit using the ON/OFF switch (B-8) and
adjust the volume to the level you prefer using the VOLUME
control (B-8).
> The POWER light (B-9) lights up green.
> When connection has been established between the units,
the LINK light (B-2) on the parent unit lights up green.

EN
9
4Position the baby unit at least 1 meter / 3 feet away from
your baby.
5Position the parent unit at the desired place within the
operating range of the baby unit but at least 1 meter / 3 feet
away from the baby unit. For more information on the
operating range see ‘Technical specifications’.
➜Your can now monitor you baby!
Using your baby monitor
Other features
Avoiding interference (channel selection)
Always make sure that the CHANNEL selection switches (A-8,
B-7) inside the battery compartments (A-9, B-10) on both units
are set to the same position! With the CHANNEL selection
switches (A-8, B-7) you can select sixteen different channel
positions. If you experience interference from other baby
monitors, radio devices, etc. select a different channel.
1Open the battery compartment covers (A-9, B-10) of both
units.
• Parent unit: slide down the cover.
• Baby unit: use a coin.
2If you are operating the units on battery power, remove the
batteries from both units.

3Use a small, flat screwdriver to rotate the inner circle of the
channel selection switches (A-8, B-7) to the desired position.
Make sure both units are set to the same channel.
> If you don’t experience any interference after testing the
connection, close the battery compartment covers (A-9,
B-10). If you do experience interference, try switching to
another channel.
4Put batteries back in place and close the battery
compartments.
Adjusting microphone sensitivity
With the microphone sensitivity control (A-7) on the baby unit,
you can set the sound, coming from the baby unit, to the
desired level: low, mid or high.When set to the maximum level,
the baby unit monitors all sounds. If no sound is picked up, the
baby monitor will not monitor since continuous transmission is
prohibited by law.You can only change the microphone
sensitivity if the connection between the baby unit and the
parent unit is established (when LINK light (B-2) on the parent
unit lights continuously green).
•Use the microphone sensitivity switch (A-7) to adjust the
baby unit microphone sensitivity to the desired level.
You can use your own voice as a sound reference.
> The POWER light (A-6) on the baby unit lights up yellow
when a sound is picked up.
EN Other features
10