Philips SC465 User manual

SCD465
User manual 4
Mode d’emploi 17
Instrucciones de manejo 30
Bedienungsanleitung 43
Gebruiksaanwijzing 56
Istruzione per l’uso 69
Manual de utilização 82
Od  95
Bruksanvisning 108
Vejledning 121
Bruksanvisning 134
Käyttööhje 147
Kullanım talimatları 160
TR
SU
NO
DK
SV
GR
PR
IT
NL
DE
ES
FR
EN

2

3
A. Baby unit
B. Parent unit

A. Baby unit
A-1 ON/OFF button
A-2 Night light
A-3 DC 9V ——<<++power supply jack
A-4 Microphone
A-5 POWER light
A-6 Microphone sensitivity switch
A-7 Channel selection switch
A-8 Battery compartment cover
A-9 AC power adapter
A-10 Power plug
B. Parent Unit
B-1 AC power adapter
B-2 Power plug
B-3 Charging base
B-4 Charging light
B-5 LINK light
B-6 Loudspeaker
B-7 POWER light
B-8 Sound level lights
B-9 ON/OFF switch / VOLUME control
B-10 Channel selection switch
B-11 LINK alarm switch
B-12 Battery compartment cover
B-13 Rechargeable battery pack
B-14 DC 9V ——<<++power supply jack
C.What else you’ll need
– Coin (to open the battery compartment of baby unit)
– Small, flat screwdriver (to set the channel selection switches
and to open battery compartment of parent unit)
EN Legend of functions
4

EN
5
3 Illustrations
4 Legend of functions
4 Baby unit
4 Parent unit
4 What else you need
5 Contents
6 Welcome
6 Safety information
7 Getting your baby monitor ready
7 Baby unit
7 Parent unit
8 Using your baby monitor
9 Features
9 Avoiding interference
10 Adjusting microphone sensitivity
10 Monitoring baby silently
11 Switching the nightlight on and off
11 Switching the LINK alarm on and off
12 Troubleshooting
13 Frequently asked questions
14 Technical specifications
15 Important information
15 Replacing the battery packs
16 Environmental information
16 Maintenance
16 Need help?
Contents

Philips is dedicated to produce caring, reliable products to give
parents the reassurance they need.With this baby monitor you
can hear your baby from wherever you are in and around your
house.With sixteen different channel options you will
experience minimal interference.
Philips Baby Care, taking care together
Safety information
Please read this user manual carefully before using your baby
monitor and keep it for future reference.This baby monitor is
intended as an aid. It is not a substitute for responsible and
proper adult supervision and should not be used as such.
• Make sure the baby unit and adapter cable are always out of
reach of the baby (at least 1 meter / 3 feet away).
• Never place the baby unit inside the baby’s bed or playpen.
• Never cover the baby monitor (with a towel, blanket, etc.).
• Never use the baby monitor in moist places or close to
water.
• Check if the voltage indicated on the type plate of the
adapters (A-10, B-1) correspond to the local power voltage
before connecting to the AC power supply.
• Do not expose the baby monitor to extreme cold, heat or
light (e.g. direct sunlight).
• To prevent electric shock, do not open the inside of the baby
unit and parent unit (except for the battery compartment
cover)
• The antennas on both units are fixed; do not try to extend
them.
EN Welcome
6

EN
7
Baby unit
The baby unit can be mains or battery operated.When batteries
are installed, you have an automatic back up in case of mains
failure.
Mains operated use
1Connect the power adapter cord to the power supply jack
(DC 9V ——<<++- A-3) of the baby unit.
2Connect the AC power adapter (A-9) to a wall outlet.
➜The baby unit is now ready for mains operated use.
Battery operated use
1Remove the battery compartment cover (A-8) of the baby
unit, using a coin.
2
Insert four 1,5V AA batteries, noting the + and – configuration
inside the battery compartment (batteries are not supplied, we
recommend Philips Alkaline batteries).
3Close the battery compartment cover (A-8), using a coin.
➜The baby unit is now ready for battery operated use.
Parent unit
A rechargeable battery pack has already been installed in the
parent unit.
1Connect the power adapter cord (B-2) to the power supply
jack (DC 9V ——<<++- B-14) of the charging base (B-3).
2Connect the AC power adapter (B-1) to a wall outlet.
3Place the parent unit in the charging base (B-3).
> The charging light (B-4) lights up red.
4Leave the parent unit in the charging base (B-3) until the
batteries are fully charged (at least 14 hours).
>
When the batteries are fully charged, the charging light (B-4)
will gradually dim.The parent unit can now be taken out of
the charging base and used cordlessly for up to 10 hours.
Getting your baby monitor ready

> When the POWER light (B-7) flashes red, battery power is
low. Place the parent unit in the charging base (B-3) to
recharge the batteries.
➜The parent unit is now ready for use!
Using your baby monitor
1Position both units in the same room to test the connection.
Make sure the baby unit is at least 1 meter / 3 feet away from
the parent unit.
2Press the ON/OFF button (A-1) to switch on the baby unit.
> The POWER Light (A-5) lights up green.
3Switch on the parent unit using the ON/OFF switch (B-9) and
adjust the volume to the level you prefer using the VOLUME
control (B-9).
> The POWER light (B-7) lights up green.
> When connection has been established between the units,
the LINK light (B-5) on the parent unit lights up green.
4Position the baby unit at least 1 meter / 3 feet away from
your baby.
5Position the parent unit at the desired place within the
operating range of the baby unit but at least 1 meter / 3 feet
away from the baby unit. For more information on the
operating range see ‘Technical specifications’.
➜Your can now monitor you baby!
EN Getting your baby monitor ready
8

EN
9
Avoiding interference (channel selection)
Always make sure that the channel selection switches (A-7,
B-10) inside the battery compartments on both units are set to
the same position!
With the channel selection switches (A-7, B-10) you can select
sixteen different channel positions. If you experience
interference from other baby monitors, radio devices, etc. select
a different channel.
1Open the battery compartment covers (A-8, B-12) of both
units.
• Parent unit: use a screwdriver and slide down the cover.
• Baby unit: use a coin.
2
Lift up the rechargeable battery pack (B-13) of the parent unit.
If you are operating the baby unit on battery power, remove
the batteries from the unit.
3Use a small, flat screwdriver to rotate the inner circle of the
channel selection switches (A-7, B-10) to the desired position.
Make sure both units are set to the same channel.
4Put batteries and battery pack back in place.
5Close the battery compartment covers (A-8, B-12).
Features

Adjusting microphone sensitivity
With the microphone sensitivity switch (A-6) on the baby unit,
you can set the sound, coming from the baby unit, to the
desired level: low, mid or high.When set to the maximum level,
the baby unit monitors almost all sounds.You can only change
the microphone sensitivity if the connection between the baby
unit and the parent unit is established (when the LINK light
(B-5) lights continuously green).
• Use the microphone sensitivity switch (A-6) to adjust the
baby unit microphone sensitivity to the desired level.
You can use your own voice as a sound reference.
> The POWER light (A-5) on the baby unit lights up yellow
when a sound is picked up.
Monitoring baby silently
• Use the ON/OFF switch / VOLUME control (B-9) on the
parent unit to set the volume to the lowest level.
Do not switch off the parent unit completely!
> The sound level lights (B-8) on the parent unit visually alert
you to baby’s sounds.The more sounds your baby makes,
the more lights you will see.
> When no sound is detected all sound level lights (B-8) will
be off.
EN Features
10