Philips CED228/58 User manual

Register your product and get support at
CED228
ENG Quick Start Guide
English
Overview of parts
These are the supplierd parts needed to connect and install this unit.
a
c
f
de
b
aCarry case with front panel stored inside
bTrim plate
cStandard connector
dRubber cushion
eRemoval keys x 2 pcs
fScrew x 5 pcs
Connect wires: ISO connectors
1Pull out the ISO connectors from the
car dashboard and connect them to
the bigger end of the supplied standard
connector.
2Connect the other end of supplied
standard connector to the unit.
3Do the other connections, if applicable.
Connect wires: without ISO connectors
1
2
3
4
5
6
7
8
1Cut off the bigger end of the supplied standard connector.
2Check the car’s wiring carefully, then connect them to the standard connector.
Connector Connect to
1Black wire A metal surface of the car
First connect the black ground (earth) lead, then connect the
yellow and red power supply leads.
2Yellow wire The +12V car battery which is live at all times.
3Orange/white wire Illumination switch
4Red wire The +12V power terminal which is live in the accessory
(ACC) position of the ignition switch
If there is no accessory position, connect to the +12V car bat-
tery terminal that is always live. Be sure to connect the black
ground (earth) lead to a metal surface of the car first.
5Green and green/black wires Left speaker (Rear)
6White and white/black wires Left speaker (Front)
7Gray and gray/black wires Right speaker (Front)
8Purple and purple/black wires Right speaker (Rear)
3Connect the supplied standard connector to the unit.
4Do the other connections, if applicable.
Connect parking brake cable
Connect reverse driving cable

Attach the front panel Mount in the dashboard
Note
For proper operation of the DVD player, the chassis must be mounted within 20 degree horizontal.
•
Ensure that the unit is mounted within this limitation.
Check wire connection before you mount the unit into a car.
•
If preset radio stations are lost when the ignition key is turned• OFF and then back ON, reconnect the
red leads crosswise to the yellow ones.
1If the car does not have an on-board drive or navigation computer, disconnect the negative terminal
of the car attery.
If you disconnect the car battery in a car that has an on-board drive or navigation computer, the•
computer may lost its memory.
If the car battery is not disconnected, to avoid short-circuit, ensure that bare wires do not touch•
each other.
2Ensure that car dashboard opening is within
these measurements.
3Remove the two transport screws on the top
of the unit.
4Remove the mounting sleeve with the removal
keys.
5Install the sleeve into the dashboard and bend
the tabs outward to fix the sleeve.
If the unit is not fixed by sleeve but by the•
supplied screws, skip this step.
1Attach the trim plate.
2Insert the left side of the panel
in the chassis until it is correctly
engaged.
3Press the right side of the panel
until the mechanism locks it into
place.
4Close the front panel.
6Place the rubber cushion over the end of the
bolt.
7Slide the unit into the dashboard until a click
sound is heard.
Turn on
1Press the knob to turn on the unit.
The unit plays the last listened program: DVD,Tuner, USB or SD/MMC Card (if there is USB
»
device or SD/MMC card connected).
To turn off the unit, press the• knob for more than 2 seconds.
When the unit is idle for over 3 minutes, it goes to standby mode and displays screen saver.•
Set clock
1Press MENU.
2Press the navigation buttons to select [SETTINGS], then press SEL on the remote control.
3Select [SYSTEM], then press .
4Select [TIME MODE], then press .
The time mode options are displayed:
»
[12 hour mode]•
[24 hour mode]•
5Select a mode, then press SEL.
6Press to return to previous menu and select [TIME ADJUST], then press .
7Press or to enter clock, then press SEL.
Tune to a radio station
1Press SOURCE to select Tuner.
2Press and hold or to select band.
»[FM] or [AM] is displayed.
3Press or to tune to a radio station manually.
To search for radio station automatically, press• or for 3 seconds.
Play discs
1Press to open the front panel.
2Insert the disc into the disc slot with label side facing up.
Play resumes from the point where it was last stopped.
»
3To remove the disc, press the button.
When the disc is ejected, the unit switches toTUNER mode automatically.
»
4Close the front panel.
After a few seconds, the screen turns on.
»
For video discs, if a menu appears: press• or to select an item, then press to start play.
For discs that contain MP3s,WMAs, or JPEGs:press• or to select a folder/track/picture, then
press to start play.
Insert USB device
Insert SD/MMC card
1Slide down the USB socket cover.
2Insert the USB device into the USB socket.
The unit star ts playing from the USB
»
device automatically.
1Press to open the front panel.
2Insert the SD or MMC card into the card
slot.
The unit star ts playing from the SD/
»
MMC card automatically.
183 mm
52mm
4.75-5.56 mm
183 mm
4.75-5.56 mm
8Reconnect the negative terminal of the car battery.
Detach the front panel
The front panel can be detached and taken with you to deter theft.
Note
Before installing the unit, detach the front panel.
•
1Press to release the panel.
2Open the panel, then push the right side panel toward the left side to disengage it from the chassis.
3Take off the panel and store it in the supplied carry case to protect it from dir t or damage.
© 2009 Koninklijke Philips Electronics N.V.
All rights reserved.
CED228_58_QSG_V2.0