Philips CED228/58 User manual

EN User manual
www.philips.com/welcome
Register your product andget support at
CED228/58

1
English
EN
Contents
1 Important 2
Safety 2
Notice 2
2 Your car audio system 4
Introduction 4
What's in the box 4
Overview of the main unit 5
Overview of the remote control 7
3 Get started8
Install the car audio 8
Install remote control battery 15
Turn on 15
Select display language 15
Set clock 16
4 Play 16
Load discs 16
Insert USB device 17
Insert SD/MMC card 18
Skip/search 18
Intro play 18
Repeat play 18
Random play 19
Select subtitle language 19
Select audio language 19
Select audio mode 19
Select video output format 19
Zoom 19
5 Listen to radio 20
Tune to a radio station 20
Store radio stations in memory 20
Tune to a preset station 20
Select stereo/mono broadcasting 20
Select tuner sensitivity 21
Play with RDS 21
6 Adjust settings 23
Adjust sound 23
Adjust system settings 24
Adjust general DVD settings 25
Adjust video DVD settings 26
Select language 26
Adjust display settings 27
View DivX registration code 27
7 Others 28
Listen to other devices 28
Detach the front panel 28
Reset 28
Remove the unit 29
Replace fuse 29
Turn on/off the screen backlight 29
8 Product information 30
9 Troubleshooting 32

2EN
1 Important
Safety
 Read and understand all instructions
before you use the apparatus. If damage is
caused by failure to follow instructions, the
warranty does not apply.
 Use of controls or adjustments or
performance of procedures other than
herein may result in hazardous radiation
exposure or other unsafe operation.
 This unit is designed for negative ground
(earth) 12 V DC operation only.
 
watch video during driving.
 To ensure safe driving, adjust the volume to
a safe and comfortable level.
 Improper fuses can cause damage or

consult a professional.
 Use only the supplied mounting hardware
for a safe and secure installation.
 To avoid short circuit, do not expose the
apparatus, remote control or remote
control batteries to rain or water.
 Never insert objects into the ventilation
slots or other openings on the apparatus.
 Never place any objects other than discs
into the disc tray/slot.
 Visible and invisible laser radiation when
open. Avoid exposure to beam.
 Risk of damage to the screen! Never touch,
push, rub or strike the screen with any
object.
 Never use solvents such as benzene,
thinner, cleaners available commercially, or
anti-static sprays intended for discs.
 Clean the apparatus with soft, damp cloth.
Never use substances such as alcohol,
chemicals or household cleaners on the
apparatus.
Notice
The making of unauthorized copies of copy-
protected material, including computer

recordings, may be an infringement of
copyrights and constitute a criminal offence.
This equipment should not be used for such
purposes.

are trademarks of DivX, Inc. and are used under
license.



Manufactured under license from Dolby
Laboratories.
"Dolby" and the double-D symbol are
trademarks of Dolby Laboratories.
Other trademarks and trade names are those
of their respective owners.
This apparatus includes this label:
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)

3
English
EN
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.

device that are not expressly approved by
Philips Consumer Lifestyle may void the user’s
authority to operate the equipment.
2008 © Koninklijke Philips Electronics N.V. All
rights reserved.

notice.Trademarks are the property of
Koninklijke Philips Electronics N.V. or their
respective owners. Philips reserves the right
to change products at any time without being
obliged to adjust earlier supplies accordingly.

4EN
2 Your car audio
system
Congratulations on your purchase, and

support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
With the in-car audio system, you and your
passengers can enjoy:
 DVD,VCD or DivX video
 Music CDs
 FM or AM (MW) radio
 MP3/WMA audio from discs, USB devices
and SD/MMC cards
 Audio from external devices
What's in the box
Check and identify the contents of your
package:
a
c
g
jk
h
i
de
f
b
a Front panel carry case (includes front
panel)
b Car audio system
c Trim plate
d Remote control
e Rubber cushion
f Standardconnector
g Removal keys x 2 pcs
h Screws M5x6 mm x 5 pcs
i User manual
j Installation guide
k MP3-link cable

5
English
EN
Overview of the main unit
a MENU
 Access the system menu.
b /
 Tune for radio station.
 Skip/search for track.
c OK/MUTE
tsrqponmlkjh i
g e df
bc a
xw
uv
 Turn the unit on or off.
 Turn mute on or off.
 Adjust volume.
 
d /
 Select tuner band.
 Select folder.

6EN
e
 Return to previous menu.
 Stop searching.
 Disable screen saver.
f Screen
g
 Unlock the front panel.
h USB socket
i External equipment audio-in socket
j R/L, 6
 Select preset station no. 6.
 Select audio channel.
k 5, P/N
 Select preset station no. 5
 Select video output format.
l SHUF, 4
 Turn random play on or off.
 Select preset station no. 4
m 3, REP
 Select repeat play mode.
 Select preset station no. 3
n INTRO, 2
 Turn scan play on or off.
 Select preset station no. 2
o 1,
 Start play.
 Pause or resume play.
 Select preset station no. 1
p TA/AF
 Enable TA/AF function.
q SEARCH
 Select tuner band.
 Store radio station automatically.
r DBB
 Turn on or off Dynamic Bass Boost
(DBB) sound.
s EQ/AUDIO
 Select equalizer (EQ) setting.
 Access audio setting menu.
t SOURCE
 Select audio source.
u Disc slot
v
 Eject disc.
w SD/MMC cardslot
x RESET
 Restore default settings.

7
English
EN
Overview of the remote
control
a TITLE
 Access or exit DVD title menu.
b SOURCE
 Select connected device.
c
 Return to previous menu.
 Disable screen saver.
d VOLUME +/-
 Adjust volume.
e EQ
 Select equalizer (EQ) setting.
f DBB
 Turn on or off Dynamic Bass Boost
(DBB) sound.
g 3, REP
 Select repeat play mode.
 Select preset station no. 3
h SCH
 Store radio station automatically.
i DISP
 Display play information.
j ZOOM
 Enlarge or reduce picture or active
image size.
k ANGLE
 Select a difference angle/version of the
current DVD scene.
l R/L
 Select audio channel.
m P/N
 Select video output format.
n SUBTITLE
 Select DVD or DivX subtitle language.
o DISC MENU
 Return to DVD main menu.
p 5/6/7/8/9/0+
 Select track or preset radio station.
q SHUF, 4
 Turn random play on or off.
 Select preset station no. 4.
r 1
 Select preset station no. 1
s INTRO, 2
 Turn intro play on or off.
 Select preset station no. 2
t AUDIO
 Access audio setting menu.
u Navigation buttons
 /
Tune for radio station.

8EN
Skip/search for track.
 /
Select tuner band.
Select folder.
 SEL/

Start play.
Pause or resume play.
v MENU
 Access system menu.
w PWR
 Turn the unit on or off.
x
 Mute or unmute audio.
3 Get started
Caution
 Use the controls only as stated in this user manual.
Always follow the instructions in this chapter in
sequence.
If you contact Philips, you will be asked for the
model and serial number of your apparatus.The
model number and serial number are on the
bottom of your apparatus.Write the numbers
here:
Model No. __________________________
Serial No. ___________________________
Install the car audio
These instructions are for a typical installation.
However, if your car has different requirements,
make the corresponding adjustment. If you have
any questions regarding installation kits, consult
your Philips car audio dealer.
Caution
 This unit is designed for negative ground (earth) 12 V
DC operation only.
 Always install this unit in the car dashboard. Other
locations can be dangerous as the rear of the unit heats
up during use.
 To avoid short-circuit: before you connect, ensure that
the ignition is off.
 Ensure that you connect the yellow and red power
supply leads after all other leads are connected.
 Ensure that all loose leads are insulated with electrical
tape.
 Ensure that the leads do not get caught under screws
orin parts that will move (e.g. seat rail).
 Ensure that all ground (earth) leads are run to a
common ground (earth) point.
 Use only the supplied mounting hardware for a safe
and secure installation.
 
need to change the fuse, consult a professional.

9
English
EN
Note on the power supply lead(yellow)
 When you connect other devices to this
apparatus, ensure that the rating of the car
circuit is higher than the total fuse value of
all the connected devices.
Notes on speaker connection
 Never connect speaker wires to the metal
body or chassis of the car.
 Never connect speaker wires with stripes
to one another.
Overview of parts
These are the supplied parts needed to
connect and install this unit.
a Carry case withfront panel storedinside
b Trim plate
c Standardconnector
d Rubber cushion
e Removal keys x 2 pcs
f Screw x 5 pcs
Connect wires: ISO connectors
Caution
 Ensure that all loose leads are insulated with electrical
tape.
a
c
f
de
b
1 Pull out the ISO connectors from the car
dashboard and connect them to the bigger
end of the supplied standard connector.
2 Connect the other end of supplied
standard connector to the unit.
3 Do the other connections, if applicable.
CAMERA IN

10 EN
Connect wires: without ISO
connectors
Caution
 Ensure that all loose leads are insulated with electrical
tape.
1 Cut off the bigger end of the supplied
standard connector.
2 Check the car's wiring carefully, then
connect them to the standard connector.
Connector Connect to
1
2
3
4
5
6
7
8
1 Black wire A metal surface of the car
First connect the black
ground (earth) lead, then
connect the yellow and red
power supply leads.
2 Yellow wire The +12V car battery
whichis live at all times.
3 Orange/
white wire
Illumination switch
4 Red wire The +12V power terminal
whichis live in the
accessory (ACC) position
of the ignition switch
If there is no accessory
position, connect to the
+12V car battery terminal
that is always live. Be
sure to connect the black
ground (earth) lead to a
metal surface of the car

5 Green and
green/black
wires
Left speaker (Rear)
6 White and
white/black
wires
Left speaker (Front)
7 Gray and
gray/black
wires
Right speaker (Front)
8 Purple and
purple/
black wires
Right speaker (Rear)
3 Connect the supplied standard connector
to the unit.

11
English
EN
4 Do the other connections, if applicable.
CAMERA IN

12 EN
Connect parking brake cable
Connect reverse driving cable

13
English
EN
Attachthe front panel
1 Attach the trim plate.
2 Insert the left side of the panel in the
chassis until it is correctly engaged.
3 Press the right side of the panel until the
mechanism locks it into place.
4 Close the front panel.
Mount in the dashboard
Note
 For proper operation of the DVD player, the chassis
must be mounted within 20 degree horizontal. Ensure
that the unit is mounted within this limitation.
1 If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car attery.
 If you disconnect the car battery in
a car that has an on-board drive or
navigation computer, the computer
may lost its memory.
 If the car battery is not disconnected,
to avoid short-circuit, ensure that bare
wires do not touch each other.
2 Ensure that car dashboard opening is
within these measurements:

14 EN
3 Remove the two transport screws on the
top of the unit.
4 Remove the mounting sleeve with the
removal keys.
5 Install the sleeve into the dashboard and

183 mm
53.5mm
5mm
 
the supplied screws, skip this step.
6 Place the rubber cushion over the end of
the bolt.
7 Slide the unit into the dashboard until a
click sound is heard.

15
English
EN
8 Reconnect the negative terminal of the car
battery.
Install remote control battery
Caution
 Risk of explosion! Keep batteries away from heat,

 Risk of decreased battery life! Never mix different
brands or types of batteries.
 Risk of product damage! When the remote control is
not used for long periods, remove the batteries.
 Perchlorate Material - special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate.

1 Remove the protective tab to activate the
remote control battery.
To replace the remote control battery:
1 Open the battery compartment.
2 Insert <00_RC_Battery_Quantity> <00_
RC_Battery_Type> batteries with correct
polarity (+/-) as indicated.
Close the battery compartment.
Turn on
1 Press the knob to turn on the unit.
» The unit plays the last listened
program: DVD,Tuner, USB or SD/MMC
Card (if there is USB device or SD/
MMC card connected).
 To turn off the unit, press the knob for
more than 2 seconds.
 When the unit is idle for over 3 minutes, it
goes to standby mode and displays screen
saver.
Select display language
English is the default language for screen display.
You can change the display language.
1 Press MENU.
» The main menu is displayed.
2 On the remote control, press the
navigation buttons to select [SETTINGS],
then press SEL
» The setting menu is displayed.
3 Select [LANGUAGE] > [OSD Lang].
4 Select the language, then press SEL.
5 Press to exit.
⁚㇂Ŷဟ
Español
Português
Pyccknñ

16 EN
Set clock
1 Press MENU.
2 Press the navigation buttons to select
[SETTINGS], then press SEL on the
remote control.
3 Select [System], then press .
4 Select [Time mode], then press .
» The time mode options are displayed:
 [12 hour mode]
 [24 hour mode]
5 Select a mode, then press SEL.
6 Press to return to previous menu and
select [Time adjust], then press .
7 Press or to enter clock, then
press SEL.
4 Play
Ensure that the disc or device contains playable
music/video. (see 'Product information' on page
30)
Note
 
session is played.
 This apparatus does not support MP3PRO audio
format.
 If any special characters are present in the MP3 track
name (ID3) or album name, it may not display correctly
on the screen because these characters are not
supported.
 Some WMA is protected by Digital Rights Management
(DRM), it cannot be played on this apparatus.
 
apparatus are not displayed or played.
Loaddiscs
Warning
 
video during driving.
You can play video, audio or images stored on
the following discs:
 DVD video, DVD-R, DVD-RW
 VCD
 
CD-RW
Note
 Ensure that the disc contains playable content.
You can play DVD discs with the following
region codes:Press to open the front panel.

17
English
EN
DVD region code Countries

1 Insert the disc into the disc slot with label
side facing up.
» Play resumes from the point where it
was last stopped.
2 To remove the disc, press the button.
» When the disc is ejected, the
unit switches to TUNER mode
automatically.
3 Close the front panel.
» After a few seconds, the screen turns
on.
 For video discs, if a menu appears:
press or to select an item, then
press to start play.
 For discs that contain MP3s,WMAs,
or JPEGs: , press or to select a
folder/track/picture, then press to
start play.
Tip
 If the disc is blocked in the disc compartment, press and
hold until the disc comes out.
P
r
i
n
t
i
n
g
i
n
C
h
i
n
a
Insert USB device
1 Slide down the USB socket cover.
2 Insert the USB device into the USB socket.
» The unit starts playing from the USB
device automatically.
Remove the USB device
1 Press to turn off the unit.
2 Remove the USB device.

18 EN
Insert SD/MMC card
1 Press to open the front panel.
2 Insert the SD or MMC card into the card
slot.
» The unit starts playing from the SD/
MMC card automatically.
Remove the SD/MMC card
1 Press to turn off the unit.
2 Press the card until you hear a click sound.
» The card is now disengaged.
3 Remove the SD or MMC card.
Skip/search
During video disc play
 
number buttons on the remote control.
 To skip to the previous/next chapter, press
or .
 To search backward/forward rapidly, press
or for 3 seconds.
» [Backward]or [Forward]is displayed.
To change search spead, repeatedly press
or for 3 seconds
To resume normal play, press .
During audio disc play
 
number buttons on the remote control.
 To skip to track number over 9, press 0

 To skip to the previous/next track, press
or .
 To search backward/forward rapidly within
the current track, press or for 3
seconds .
DuringMP3/WMA play
 To select a track, press or to select a
folder, then press or to skip to the
previous/next track. Or press the number
buttons on the remote control to skip to a

 To search backward/forward rapidly within
the current track, press or for 3
seconds
For picture disc
 To skip to the previous/next picture, press
or .
Intro play

seconds of each track.
1 During play, press INTRO, 2 to select:
 [Intro][On]
of each track have been played, play
stops.
 [Intro][Off]: Cancel intro play and start
normal play.
Repeat play
For video play
During play, press 3, REP repeatedly to select:
 [Rep 1] : play the current chapter
repeatedly.
 [Rep all] :play all chapters in the title
repeatedly.
 [Rep off] : cancel repeat play.
For audio disc play
During play, press 3, REP repeatedly to select:
 [Rep 1]: play the current track repeatedly.
 [Rep all]: play all tracks repeatedly.
 [Rep off]: cancel repeat play.

19
English
EN
For MP3/WMA play
During play, press 3, REP repeatedly to select:
 [Rep 1] : play the current track repeatedly.
 [Rep dir] : play all tracks in the current
folder repeatedly.
 [Rep all]: play all tracks repeatedly.
 [Rep off] : cancel repeat play.
Random play
You can play audio tracks in random order.
1 During play, press SHUF, 4 to select:
  : starts random play for all
tracks.
 : starts random play in
current folder.
  : cancel random play.
Select subtitle language
For DVD or DivX discs that contain two or
more subtitle languages.
1 During play, press SUBTITLE on the
remote control repeatedly until the
language is selected.
Select audio language
For video discs that contain two or more audio
channels.
1 During play, press R/Lon the remote
control repeatedly until the language is
selected.
Select audio mode
When you play VCDs/CDs, you can select an
audio mode (R/L/Stereo).
1 Press R/Lrepeatedly until the audio mode
is selected.
Select video output format
The default video output format has been
chosen according to format that is broadcast
in your country. If the picture looks unusual,
change the video output.
1 Press P/Nrepeatedly to select:
 [NTSC]: used in the United States,
Canada, Japan, Mexico, the Philippines,
South Korea,Taiwan, and some other
countries.
 [PAL]: used in most of the Western
European countries (except France),
Australia, and some other countries.
 [Auto]:The correct format is set
automatically. Select this option if you
are not sure which format should be
selected.
Zoom
For DVDs,VCDs and picture CDs, you can
zoom in and out for video images or pictures.
1 Press ZOOM on the remote control
repeatedly to select rate.
 [Zoom] is displayed.
2 When the video image or picture is
enlarged, press the navigation buttons to
pan through it.