Philips CEM2000X/78 User manual

Register your product and get support at CEM2000
EN Quick Start Guide

1ab
def
45
B
g
c
A
b
a
c
d
aa
bcd
ab
ef
cd
gh
b
c
d
32

6
5mm5mm5mm5mm
5mm

Overview of parts 1
These are the supplied parts needed to connect
and install this unit.
aIn-car audio system
bSleeve
cFront panel
dStandard ISO connector
eTrim plate
fRubber cushion
gDisassembly tools
hScrews (4 pieces)
Select country/region
1Press to turn on the unit.
2Rotate to select an option:
[USA] (United States)•
[Latin] (Latin America)•
[Europe] (Western Europe)•
[ASIA](AsiaPacic)•
[Mid-East ] (Middle East)•
[Russia] (Russia)•
3Press toconrm.
Connection
Caution
•Ensure that all loose leads are insulated with
electrical tape.
For cars with ISO connectors 234
1Pull out the ISO connectors from car dash-
board and connect them to the bigger end
of the supplied standard connector.
2Connect the other end of the supplied stan-
dard connector to the unit.
3Connecttheantennaandamplierasil-
lustrated, if applicable.You can connect the
caraudiototheamplierthroughRCA-TO-
RCA cables (not supplied).
Connector Connect to
1 ANTENNA Antenna
2 FRONT LINE
OUT R (Socket)
Front right speaker
3 FRONT LINE
OUT L (Socket)
Front left speaker
4 REAR LINE
OUT R (Socket)
Rear right speaker
5 REAR LINE
OUT L (Socket)
Rear left speaker
6 SUBWOOFER Subwoofer
For cars with ISO connectors 45
Caution
•Be sure to connect the black ground (earth)
leadrst.
1Connecttheantennaandamplierasillus-
trated, if applicable.
2Cut off the bigger end of the supplied stan-
dard connector.
3Check the car’s wiring carefully and connect
them to the supplied standard connector.
4Connect the supplied standard connector to
the unit.
1 Green/black strip Left speaker (Rear)
2 White/black strip Left speaker (Front)
3 Gray/black strip Right speaker (Front)
4 Purple/black strip Right speaker (Rear)
e RED Ignition key +12V DC when
ON/ACC
f BLUE Motor/electric antenna relay
controllead/Amplierrelay
control lead
g BLACK Ground
h YELLOW To the +12V car battery
which is energized at all times

Mount in the dashboard 6
1If the car does not have an on-board drive or
navigation computer, disconnect the negative
terminal of the car battery.
If you disconnect the car battery in a car•
that has an on-board drive or navigation
computer, the computer may lose its
memory.
If the car battery is not disconnected,•
to avoid short-circuit, ensure that bare
wires do not touch each other.
2Remove the two screws on the top of the
unit.
3Remove the mounting sleeve with the sup-
plied disassembly tools.
4Install the sleeve into the dashboard and
bendthetabsoutwardtoxthesleeve.
5Place the supplied rubber cushion over the
end of the mounting bolt.
6Slide the unit into the dashboard until you
hear a click sound.
7Reconnect the negative terminal of the car
battery.
Attach the front panel 6
1Attach the trim plate.
2Insert the right side of the panel in the chas-
sis until it is correctly engaged.
3Press the left side of the panel until the
mechanism locks it into place.
Turn on
1Press to turn on the unit.
To turn off the unit, press•for over 3
seconds.
Set clock
1Press MENU.
2Press or repeatedly until currently time
is displayed.
3Turn clockwise to set hour.
4Press toconrm.
5Turn anti-clockwise to set minute.
6Press toconrm.
View clock
1Press and hold OPTIONS repeatedly until
the clock is displayed.
Listen to radio
1Press SOURCE repeatedly to select Tuner.
2Press or to select band: [FM1], [FM2],
[FM3], [AM1], or [AM2] .
3Press or to tune to a radio station
manually.
The radio station is broadcast.•
To search for a radio station automati-•
cally, press or for over 3 seconds.

© 2010 Koninklijke Philips Electronics N.V.
All rights reserved.
CEM2000_78_QSG_V1.0
Avoid prolonged use of the apparatus with volume above 85 decibels as this may damage your hearing.