Register your product and get support at CEM210
EN Quick Start Guide
34
2
1abc
efgh
d
L-CHR-CH
AMP
a
c
b
b
a
c
d
aa
bcd
ab
ef
cd
ghi
b
c
d
Overview ofparts 1
Check and identify the contents of your package:
1 In-car audio system
2 Sleeve
3 Front panel
4 Trim plate
5 Rubber cushion
6 Disassembly tools
7 Screws (4 pieces)
8 ISO connector
Connect wires
Caution
Ensure that all loose leads are insulated with
electrical tape.
For cars withISO connectors 2 3
1Pull out the ISO connectors from car
dashboard and connect them to the bigger
end of the supplied standard connector.
2Connect the other end of the supplied stan-
dard connector to the unit.
3&RQQHFWWKHDQWHQQDDQGDPSOLÀHUDVLO-
lustrated, if applicable.You can connect the
FDUDXGLRWRWKHDPSOLÀHUWKURXJK5&$72
5&$FDEOHVQRWVXSSOLHG
Connector Connect to
1$17(11$ $QWHQQD
25($5/,1(2875 Rear right speaker
35($5/,1(287/ Rear left speaker
For cars without ISO connectors 3 4
Caution
Be sure to connect the black ground (earth)
OHDGÀUVW
1 &RQQHFWWKHDQWHQQDDQGDPSOLÀHUDV
illustrated, if applicable.
2Cut off the bigger end of the supplied stan-
dard connector.
3Check the car’s wiring carefully and connect
them to the supplied standard connector.
4Connect the supplied standard connector to
the unit.
1 Green/black
strip
/HIWVSHDNHU
(Rear)
2 White/black
strip
/HIWVSHDNHU
(Front)
3 Gray/black
strip
Right speaker
(Front)
4 Purple/black
strip
Right speaker
(Rear)
e RED Ignition key +12V DC
ZKHQ21$&&
f%/8( Motor/electric antenna
relay control lead/
$PSOLÀHUUHOD\FRQWURO
lead
g%/$&. Ground
h Orange Illumination switch
i<(//2: To the +12V car battery
which is energized at all
times
Note
Check wire connection before you mount
the unit into a car.
If preset radio stations are lost when the
ignition key is turned OFF and then back
ON, reconnect the red leads crosswise to
the yellow ones.
Attachthe front panel 5
1$WWDFKWKHWULPSODWH
2Insert the right side of the panel in the
chassis until it is correctly engaged.
3Press the left side of the panel and point
the left hole at the left pillar.
4Release the panel to engage the left side.
Mount in the dashboard 5
1If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car battery.
If you disconnect the car battery in a car
that has an on-board drive or navigation
computer, the computer may lose its
memory.
If the car battery is not disconnected,
to avoid short-circuit, ensure that bare
wires do not touch each other.
2Remove the two screws on the top of the
unit.
3Remove the mounting sleeve with the
supplied disassembly tools.
4Ensure that car dashboard opening is
within these measurements:
5Install the sleeve into the dashboard and
EHQGWKHWDEVRXWZDUGWRÀ[WKHVOHHYH
6Place the rubber cushion over the end of
the bolt.
7Slide the unit into the dashboard until you
hear a click sound.
8Reconnect the negative terminal of the car
battery.
Turn on
1Press zto turn on the unit.
To turn off the unit, press zfor 3
seconds.
Set clock
1Press MENU/DISP for 3 seconds.
2Press 3or 4repeatedly to until the cur-
rently time is displayed.
3Tu r n zclockwise to set hour.
4Press zWRFRQÀUP
5Tu r n zanti-clockwise to set minute.
6Press zWRFRQÀUP
View clock
1Press MENU/DISP repeatedly until the clock
is displayed.
5
5mm
5mm5mm
Listen to radio
1Press SOURCE repeatedly to select Radio.
2Press 3or 4to select band: [FM1],[FM2],
[FM3],[AM1], or [AM2] .
3Press ∞or §to tune to a radio station
manually.
To search for a radio station
automatically, press /for 3 seconds.
3OD\DXGLRÀOHV
1Press on the front panel to release the
panel.
2Insert a CD with the printed side facing up.
3Close the panel.
Play starts automatically.
»
To pause CD play, press 1.
To resume CD play, press1 again.
Insert the USB device
1Open the cover marked on the front
panel.
2,QVHUWWKH86%GHYLFHLQWRWKH86%VRFNHW
7KHXQLWVWDUWV SOD\LQJIURPWKH86%
»
device automatically.
© 2009 Koninklijke Philips Electronics N.V.
All rights reserved.
CEM210_98_UM_V1.0
