Philips CEM2300BT User manual

Register your product and get support at
www.philips.com/support
Always there to help you
CEM2300BT
User manual
Question?
Contact
Philips

1EN
Contents
1 Safety 2
2 Your car audio system 3
Introduction 3
What's in the box 3
Overview of the system 4
3 Install the car audio system 6
Connect wires 7
Mount into the dashboard 7
Attach the front panel 9
4 Get started 10
For the rst time use 10
Set the time format 10
Set the clock 10
Turn on 10
Switch music listening zone 10
Mute the button beep 10
5 Listen to radio 11
Tune to a radio station 11
Store radio stations in memory 11
Tune to a preset station 11
Play with RDS 11
6 Play from hard media 13
Play a disc 13
Play from a USB storage device 14
7 Use Bluetooth devices 15
Connect a device 15
Play audio from a Bluetooth device 16
Make a call 16
8 Listen to an external player 17
9 Charge your USB device 17
10 Adjust sound 18
11 Adjust system settings 18
12 Others 19
Reset 19
Replace fuse 19
13 Product information 20
14 Troubleshooting 21
General 21
About the Bluetooth device 21
15 Notice 22
Compliance 22
Care of the environment 22
Trademark notice 23
Copyright 23

2EN
1 Safety
Read and understand all instructions before
you use your apparatus. If damage is caused by
failure to follow instructions, the warranty does
not apply.
• This apparatus is designed for negative
ground (earth) 12 V DC operation only.
• To ensure safe driving, adjust the volume to
a safe and comfortable level.
• Improper fuses can cause damage or
re. When you need to change the fuse,
consult a professional.
• Use only the supplied mounting hardware
for a safe and secure installation.
• To avoid short circuit, do not expose the
apparatus to rain or water.
• Never insert objects into the ventilation
slots or other openings on the apparatus.
• Clean the apparatus and frame with a soft,
damp cloth. Never use substances such as
alcohol, chemicals or household cleaners
on the apparatus.
• Never place any objects other than discs
into the apparatus.
• Never use solvents such as benzene,
thinner, cleaners available commercially, or
anti-static sprays intended for discs.
• Visible and invisible laser radiation when
open. Avoid exposure to beam.
Caution
•Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
laser exposure or other unsafe operation.
• The apparatus shall not be exposed to
dripping or splashing.
• Do not place any sources of danger on the
apparatus (e.g. liquid lled objects, lighted
candles).

3EN
2 Your car audio
system
Congratulations on your purchase, and
welcome to Philips! To fully benet from the
support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
With the in-car audio system, you can listen to
• FM or AM (MW) radio,
• Audio from a CD or MP3 disc,
• Audio from a USB storage device,
• Audio from a Bluetooth device, and
• Audio from an external player.
Playable media:
• Disc
• Audio CD, MP3-CD,WMA-CD
• CD-R, CD-RW
• USB storage device
• Compatibility: USB 2.0, USB 1.1
• Class support: MSC (Mass Storage
Class)
• Maximum capacity: 32 GB
• Files
• File system: FAT16, FAT32
• Maximum number of folders: 99
• Maximum number of tracks/les: 999
• Maximum level of directory: 8
• .mp3 les
Sampling frequencies: 32 kHz, 44.1 kHz,
48 kHz
Bitrates: 8-320 kbps and variable
bitrates
• .wma les
Versions:V4,V7,V8,V9 (L1 and L2)
Sampling frequencies: 44.1 kHz, 48 kHz
Bitrates: 64-192 kbps and variable
bitrates
• ID3 tag V2.0 or later
• Unsupported les:
AAC, WAV, and PCM les
DRM protected WMA les (.wav, .m4a,
.m4p, .mp4, and .aac)
WMA les in lossless format
What's in the box
Check and identify the contents of your
package:
a Main unit (with a sleeve)
b Carrying case (with the front panel
included)
c Trim plate
d Disassembly tool x 2
e Rubber cushion
f Screw x 1
g User manual
abc
e
df
g

4EN
Overview of the system
a
• Unlock the front panel.
b
• Press to return to the previous menu.
• Press and hold to access the system
menu.
c
• For .wma and .mp3 tracks, press to
select the previous folder.
• In radio mode, press to select a tuner
band.
• Press and hold to activate the selection
of listening zones.
ab cd
ef
ts rqpo nmlkji ghuv
w
d Disc slot
e LCD screen
f
• Eject the disc from the disc
compartment.
g
• Connect to a USB storage device.
h AUDIO IN
• Connect to the audio output socket
(usually the headphone socket) of an
external device.

5EN
i
• Start, pause, or resume the play of
tracks.
• In radio mode, press to select the
preset radio station of No. 6.
• In radio mode, press and hold to store
the current radio station at channel
No. 6.
j
• In radio mode, press to select the
preset radio station of No. 5.
• In radio mode, press and hold to store
the current radio station at channel
No. 5.
k
• In radio mode, press to select the
preset radio station of No. 4.
• In radio mode, press and hold to store
the current radio station at channel
No. 4.
• For .wma and .mp3 tracks, press
repeatedly to select a play mode: play
all tracks randomly ([SHU ALL]), play
tracks in the current folder randomly
([SHU FLD]), or play all tracks in the
storage device in sequence ([SHU
OFF]).
l
• In radio mode, press to select the
preset radio station of No. 3.
• In radio mode, press and hold to store
the current radio station at channel
No. 3.
• For .wma and .mp3 tracks, press
repeatedly to select a repeat mode:
repeat the current track ([REP ONE]),
repeat all tracks in the current folder
([RPT FLD]), or repeat all tracks in the
storage device ([RPT ALL]).
m
• In radio mode, press to select the
preset radio station of No. 2.
• In radio mode, press and hold to store
the current radio station at channel
No. 2.
• For .wma and .mp3 tracks, press to
access the folder list.
n
• In radio mode, press to select the
preset radio station of No. 1.
• In radio mode, press and hold to store
the current radio station at channel
No. 1.
• For .wma and .mp3 tracks, press to
access the track list.
o /DISP
• Press repeatedly to display available
information about the current track.
• Press repeatedly to display available
RDS information.
• Press and hold to display the set clock.
p AS/SOURCE
• Press repeatedly to select a source.
• In radio mode, press and hold to
activate the automatic search of radio
stations.
q
• Press and hold to enable or disable
the DBB (dynamic bass boost) sound
effect.
• For .wma and .mp3 tracks, press to
select the next folder.
• In radio mode, press to select a tuner
band.
r
• Press to turn on the system.
• Press and hold to turn off the system.
• Press to mute the speakers or release
them from mute status.
• Press to conrm an option.
• Rotate to switch between menu
options.
• Rotate to adjust the volume level.
s
• Press repeatedly to select a preset
sound equalizer.
• Press and hold to activate the setup of
bass, treble, balance, and fader.

6EN
t /
• Tune to a radio station.
• Press to skip to the previous or next
track.
• Press and hold to rewind a track or
search fast forward.
u
• Press to hang up an ongoing call.
• When there is an incoming call, press
to reject it.
• When it is not in a call, press to enable
or disable the MAX Sound feature.
v
• When there is an incoming call, press
to answer.
• Press and hold to redial the last called
number.
• In a call, press and hold to transfer the
voice between the phone and the car
speakers.
w RESET
• Press to reset the system to factory
default settings.
3 Install the car
audio system
Caution
•Use the controls only as stated in this user manual.
Always follow the instructions in this chapter in
sequence.
These instructions are for a typical installation.
However, if your car has different requirements,
make the adjustment accordingly. If you have
any question regarding installation kits, consult
your local retailer.
Note
•This system is designed for negative ground (earth) 12V
DC operation only.
•Always install this system in the car dashboard. Other
locations can be dangerous as the rear of the system
heats up during use.
•To avoid short-circuit: before you connect, make sure
that the ignition is off.
•Make sure that you connect the yellow and red power
supply leads after all other leads are connected.
•Make sure that all loose leads are insulated with
electrical tape.
•Make sure that the leads do not get caught under
screws or iron parts that will move (e.g. seat rail).
•Make sure that all ground (earth) leads are run to a
common ground (earth) point.
•Use only the supplied mounting hardware for a safe
and secure installation.
•Improper fuses can cause damage or re. When you
need to change the fuse, consult a professional.
•When you connect other devices to this system, make
sure that the rating of the car circuit is higher than the
total fuse value of all the connected devices.
•Never connect speaker wires to the metal body or
chassis of the car.
•Never connect speaker wires with stripes to one
another.

7EN
Connect wires
Note
•Consult a professional to connect CEM2300BT as
instructed below.
1 Check the car's wiring carefully and
connect them to the the male connector.
ISO male
connectors
Connect to
a Green strip, black-
edged green strip
Left speaker (Rear)
b White strip, black-
edged white strip
Left speaker (Front)
c Gray strip, black-
edged gray strip
Right speaker (Front)
d Purple strip, black-
edged purple strip
Right speaker (Rear)
e Red Ignition key +12V
DC when ON/ACC
f Blue Motor/electric
antenna relay control
lead
g White edged blue
strip
Amplier relay
control lead
h Black Ground
i Yellow To the +12V car
battery which is
energized at all times
2 Connect the antenna and amplier as
illustrated, if applicable.
Connector Connect to
1 ANTENNA Antenna
2 Socket for ISO male
connectors
As indicated in
Step 1 above
3 REAR LINE OUT R
(Socket)
Rear right
speaker
4 REAR LINE OUT L
(Socket)
Rear left speaker
5 OE REMOTE (Purple) OE Remote
6 OE REMOTE (Black) Ground
7 External Mic (Black
connector)
External
microphone
Tip
•The pin arrangement for the ISO connectors depends
on the type of vehicle you drive. Be sure to make
proper connections to prevent damage to the unit.
Mount into the dashboard
1 If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car battery.

8EN
• If you disconnect the car battery in
a car that has an on-board drive or
navigation computer, the computer
may lose its memory.
• If the car battery is not disconnected,
to avoid short-circuit, ensure that the
bare wires do not touch each other.
2 Ensure that car dashboard opening is
within these measurements:
3 Remove the mounting sleeve with the
supplied disassembly tools.
4 Install the sleeve into the dashboard and
bend the tabs outward to x the sleeve.
Note
•If the unit is not xed by sleeve but by the supplied
screws, skip this step.
183 mm
53mm
5mm
5 Place the supplied rubber cushion over the
end of the mounting bolt.
6 Slide the unit into the dashboard until you
hear a click sound.
183 mm
53.5 mm

9EN
7 Reconnect the negative terminal of the car
battery.
Attach the front panel
1 Insert the notch on the front panel to the
chassis on the main unit.
2 Press the left end of the front panel
inwards until it is securely locked with a
"click".
Detach the front panel
Note
•Before you detach the front panel, make sure that the
system is turned off.
1 Press to release the front panel.
2 Pull the front panel outwards to remove it.

10 EN
4 Get started
For the rst time use
Note
•Select correct country/region for this unit, otherwise
the unit can not work properly.
1 Press to turn the unit on.
» [SELECT OPERATING REGION] is
displayed.
2 Rotate to select an option:
• [USA] (United States)
• [LATIN] (Latin America)
• [EUROPE] (Western Europe)
• [RUSSIA] (Russia)
• [MID-EAST] (Middle East)
• [ASIA] (Pacic)
• [JAPAN] (Japan)
• [AUSTRLIA] (Australia)
3 Press to conrm.
Set the time format
1 Press and hold .
2 Press or repeatedly until [CLOCK
FORMAT] is displayed.
3 Rotate to select a setting.
• [CLK 12H]: 12-hour time format
• [CLK 24H]: 24-hour time format
Set the clock
1 Press and hold .
2 Press or repeatedly until [CLOCK
SET] is displayed.
3 Rotate to set the hour.
4 Press to conrm.
5 Rotate to set the minute.
6 Press to conrm.
Display the clock
In any mode, press and hold until the clock is
displayed.
• Press any key to cancel the clock
display.
Turn on
• To turn on the unit, press .
• To turn off the unit, press and hold
until the unit is turned off.
Switch music listening zone
Philips’ innovative Zone technology enables
driver or passengers to enjoy music with the
best speakers balance and experience more
vivid spacial effect as the artist is intended to
create.You can switch the music listening zone
from driver to passengers for the best speaker
sound settings in car.
1 Press and hold .
» The current setting is displayed.
2 Press / to select a setting.
• [ALL]
• [FRONT] (Front)
• [RIGHT] (Right)
• [LEFT] (Left)
Mute the button beep
Each time you press a button, the unit beeps.
You can turn this beep sound on or off.
1 Press and hold .
2 Press or repeatedly until [BEEP
TONE] is displayed.
3 Rotate to select a setting:
• [BEEP ON]: turn the beep sound on.
• [BEEP OFF]: turn the beep sound off.

11EN
5 Listen to radio
Tune to a radio station
1 Press SOURCE repeatedly to select radio
mode.
2 Press / repeatedly to select a band:
[FM1],[FM2], [FM3], [AM1], or [AM2].
3 Press and hold or until the
frequency digit is ashed.
4 Press or to tune to a radio station
manually.
» The radio station is broadcast.
• To search for a radio station automatically,
press or .
Select tuner region
You can select suitable country/region of the
radio.
1 Press and hold .
2 Press or repeatedly until [AREA] is
displayed..
3 Rotate to select a region.
• [USA] (United States)
• [LATIN] (Latin America)
• [EUROPE] (Western Europe)
• [RUSSIA] (Russia)
• [MID-EAST] (Middle East)
• [ASIA] (Asia Pacic)
• [JAPAN] (Japan)
• [AUSTRLIA] (Australia)
4 Press to conrm.
Select tuner sensitivity
To receive more radio stations or only stations
with strong signal, you can adjust the tuner
sensitivity.
1 Press and hold .
2 Press or repeatedly until [LOCAL] is
displayed.
3 Rotate to select a setting.
• [LOCAL ON] (local on): only stations
with strong signal can be broadcast.
• [LOCAL OFF] (local off): stations
with strong and weak signals can be
broadcast.
Store radio stations in
memory
You can store up to 6 stations in each band.
Store stations automatically
• In Radio mode, press and hold AS until
[STORE - - -] is displayed.
» The six strongest stations of the
selected band are saved in preset
channel automatically.
Store stations manually
1 Tune to a station that you want to store.
2 Press a numeric button for 3 seconds.
» The station is saved in the selected
channel.
Tune to a preset station
• Press a numeric key to select a preset
station.
Play with RDS
The RDS (Radio Data System) function
operates only in areas with FM stations
broadcasting RDS signals. If you tune to an RDS
station, the station name are displayed.

12 EN
Turn on RDS
Note
•The default setting for RDS is on.
1 Press and hold .
2 Press or repeatedly until [RDS] is
displayed.
3 Rotate to select [RDS ON].
» The RDS function is turned on.
Select program type
Before tuning to RDS stations, you can select
program type and let the unit search only for
programs of the selected category.
1 Press and hold ..
2 Press or repeatedly until [PTY] is
displayed.
3 Press to conrm.
4 Rotate to select a type, then press
to conrm.
Item Program
type
Description
1 NEWS News services
2 AFFAIRS Politics and current
affairs
3 INFO Special information
programs
4 SPORT Sports
5 EDUCATE Education and
advanced training
6 DRAMA Radio plays and
literature
7CULTURE Culture, religion and
society
8SCIENCE Science
9VARIED Entertainment programs
10 POP M Pop music
11 ROCK M Rock music
12 EASY M Light music
13 LIGHT M Light classical music
14 CLASSICS Classical music
15 OTHER M Special music programs
16 WEATHER Weather
17 FINANCE Finance
18 CHILDREN Children’s programs
19 SOCIAL Social Affairs
20 RELIGION Religion
21 PHONE IN Phone In
22 TRAVEL Tr ave l
23 LEISURE Leisure
24 JAZZ Jazz Music
25 COUNTRY Country Music
26 NATION M National Music
27 OLDIES Oldies Music
28 FOLK M Folk Music
29 DOCUMENT Documentary
30 TEST Alarm Test
31 ALARM Alarm
Select alternate frequencies
If the radio signal is poor, turn on AF (Alternate
Frequency) to search for another station with
stronger signal.
1 Press and hold .
2 Press or repeatedly until [AF] is
displayed.
3 Rotate to select a setting.
• [AF ON]: turn AF mode on.
• [AF OFF]: turn AF mode off.
Set region for AF tuning
You can dene AF tuning region:
[REG ON] Only stations in current region
can be tuned to automatically.
[REG OFF] All stations can be tuned to
automatically.
1 Press and hold .
2 Press or repeatedly until [REG] is
displayed.
3 Rotate to select a setting.

13EN
Receive trafc announcement
If you do not want to miss trafc announcement
when enjoying music, turn on the TA (Trafc
Announcement) function.
1 Press and hold .
2 Press or repeatedly until [TA] is
displayed.
3 Rotate to select a setting.
• [TA ON]: when there is trafc
announcement, the unit switches to
the tuner mode (regardless of the
current mode) and begins to broadcast
the trafc conditions. When the trafc
announcement is over, it returns to the
previous mode.
• [TA OFF]: trafc announcement does
not cut in.
Note
•If the current received TA signal remains weak for
over 120 seconds, the unit will activate TA Seek mode
automatically.The TA Seek will seek for other station
with good condition of TA signal.
Tip
•When a trafc announcement cuts in, user can press
to terminate the trafc announcement, and the unit will
resume to previous playback mode.
Set RDS clock
You can use time signal that is broadcast
together with the RDS signal to set the clock of
the unit automatically.
1 Press and hold .
2 Press or repeatedly until [CT] is
displayed.
3 Rotate to select a setting:
• [CT ON]:Turn on the RDS clock.Time
shown on the unit synchronizes with
that on the RDS station.
• [CT OFF]:Turn off the RDS clock.
Tip
•The accuracy of the transmitted time depends on the
RDS station that transmits the time signal.
6 Play from hard
media
You can use this system to listen to audios that
are stored on a compatible disc or USB storage
device.
Play a disc
Note
•You cannot play a CD encoded with copyright
protection technologies.
•Ensure that the disc contains playable content.
Insert a CD with the printed side facing up.
» Play starts automatically.
• To pause CD play, press .
• To resume CD play, press again.
• To skip to the previous/next track, press
or .
• To search backward/forward rapidly within
the current track, press and hold or
.
• To eject the CD, press on the front panel.
Tip
•If the disc is blocked in the disc compartment, press and
hold until the disc comes out.

14 EN
Play from a USB storage
device
This system can play .mp3 and .wma les that
are copied onto a compatible storage device.
Note
•Gibson Innovations does not guarantee compatibility
with all storage devices.
•NTFS (New Technology File System) le system is not
supported.
1 Connect a compatible USB storage device.
2 Press AS/SOURCE repeatedly to switch
the source to [USB].
3 If the play does not start, press .
Control play
Button Function
/ Press repeatedly to select a
folder.
Start, pause or resume play.
/ Press to play the previous or
next track.
/ Press and hold to rewind a
track or search forward fast.
DISP Press repeatedly to display
available information about the
current track.
Press repeatedly to select a
repeat mode:
• [REP TRK] (repeat one
track): play current track
repeatedly.
• [REP FLD] (repeat a folder):
play all tracks in the current
folder repeatedly.
• [REP ALL] (repeat all tracks):
play all tracks repeatedly.
Press repeatedly to select a
play mode:
• [SHUF FLD]: start random
play for all tracks in the cur-
rent folder.
• [SHUF ALL]: start random
play for all tracks.
• [SHUF OFF]: cancel shufe
play.
Switch tracks
During play, you can switch tracks or folders
quickly.
Switch tracks directly
1 Press to access the track list.
» The le name of current track scrolls.
2 Rotate to toggle through tracks.
3 Press to play the selected track.
Switch folders for a track
1 Press to access the folder list.
» The name of current folder scrolls.
2 Rotate to toggle through folders.
3 Press to select the folder.
» The system starts playing the rst track
under the folder.

15EN
7 Use Bluetooth
devices
With this car audio system, you can listen to
audio from a player or make a call through
Bluetooth.
Connect a device
Note
•Gibson Innovations does not guarantee the
compatibility with all Bluetooth devices.
•Before pairing a device with this system, read its user
manual for Bluetooth compatibility.
•Make sure that Bluetooth function is enabled on your
device, and your device is set as visible to all other
Bluetooth devices.
•At one time, you can connect only one Bluetooth
device to this system.
•The operational range between this system and a
Bluetooth device is approximately 3 meters (9 feet).
•Any obstacle between this system and a Bluetooth
device can reduce the operational range.
•Keep away from any other electronic device that may
cause interference.
On your device, follow the steps below.
1 Search for Bluetooth devices.
2 In the device list, select CEM2300BT.
3 Enter the default password "0000", and
then conrm the password entry.
» If the pairing succeeds, [PAIRED] is
displayed on the LCD screen of this
system.
4 Enable or permit the connection with
CEM2300BT.
» If the connection succeeds,
[CONNECTED] scrolls and is
displayed on the LCD screen of this
system.
» If the connection fails, [FAILED] is
displayed on the LCD screen of this
system.
Disconnect a device
1 Press and hold to access the system
menu.
2 Press / repeatedly until [DISCONN]
is displayed.
3 Press .
» [WAIT] is displayed with -, --, and
--- blinking alternately until [DISCNN
OK] scrolls.
Tip
•You can also complete the disconnection on your
device.
Reconnect a device
Some Bluetooth devices support the automatic
reconnection with a paired Bluetooth device.
If your device does not support automatic
reconnection, reconnect it with this system
manually.
1 Press and hold to access the system
menu.
2 Press / repeatedly until [CONNECT]
is displayed.
3 Press .
» [WAIT] is displayed with -, --,
and --- blinking alternately until
[CONNECTED] scrolls or [FAILED]
appears.
» If [CONNECTED] scrolls, this system
is reconnected to the last connected
device.
Tip
•You can also complete the reconnection on your
device.

16 EN
Play audio from a Bluetooth
device
If the connected Bluetooth device supports
Advanced Audio Distribution Prole (A2DP),
you can listen to tracks that are stored on the
device through the system. If the device also
supports Audio Video Remote Control Prole
(AVRCP) prole, you can control play on the
system.
1 Play a track on the connected device.
2 Press SOURCE repeatedly to switch the
source to [BT AUDIO].
» Play starts automatically.
• To pause or resume play, press .
• To skip to the previous or next track,
press / .
Note
•If the connected device does not support the AVRCP
prole, control play on the connected device.
Make a call
Note
•Keep the Bluetooth connection active between the
system and your mobile phone.
Call a number
On your mobile phone, call a number.
» [CALLING] is displayed.
Redial the last called number
• Press and hold .
» [REDIAL] is displayed.
Pick up an incoming call
When the system receives an incoming call, the
phone number or [PHONE IN] is displayed.
Press to answer the call.
Reject an incoming call
Press and hold until [END] is displayed.
End a call
To end an on-going call, press .
Transfer a call to mobile phone
By default, the voice comes from the
loudspeakers during a call.
1 Press and hold until [TRANSFER] is
displayed.
» The loudspeakers are muted, and the
voice comes from your mobile phone
only.
2 Take up your mobile phone for the
conversation.

17EN
8 Listen to an
external player
You can use the system to amplify the audio
input from an external player, for example, MP3
player.
1 Press AS/SOURCE repeatedly to switch
the source to [AUDIO IN].
2 Connect an audio input cable with a 3.5
mm connector on both ends between
• the AUDIO IN socket on the front
panel, and
• the audio output socket (usually the
headphone socket) on the external
player.
3 Play audio on the external player.
9 Charge your
USB device
You can charge your USB device, for example,
smart phone, with this product.
Note
•The output voltage through the USB socket is 5V with
output current 1.0 A.
Connect your USB device to this product with
USB cable. Once the USB device is connected
and recognized, it begins to charge automatically.

18 EN
10 Adjust sound
The following operations are applicable to all
supported media.
Button Function
Rotate to increase or decrease the
volume level.
Press to mute or restore sound.
When it is not in a call, press to enable
or disable the MAX Sound feature.
Press and hold to enable or disable
the DBB (dynamic bass boost) sound
effect.
Press to select a preset sound
equalizer.
• [OPTIMAL] (optimal)
• [FLAT] (at)
• [POP] (pop)
• [USER] (user)
• [TECHNO] (techno)
• [ROCK] (rock)
• [CLASSIC] (classic)
• [JAZZ] (jazz)
1Press and hold to activate the setup
of customized sound equalizer.
2Press or repeatedly to select
the item to be adjusted:
• [BASS] (bass) range: -7 to +7.
• [TREBLE] (treble) range: -7 to
+7.
• [BAL] (balance) range: 12L to
12R. (L = left speaker, R = right
speaker)
• [FADER] (fader) range: 12R to
12F. (R = rear speaker, F = front
speaker)
3Rotate to select a value.
11 Adjust system
settings
1 Press to access system settings.
2 Press or repeatedly until one of the
following settings scrolls.
• [BEEP TONE], [DIMMER], [DEMO],
[BLACK OUT], or [DANCE]
3 Rotate to change the setting.
[BEEP
TONE]
[BEEP ON] Enable the
beep sound
of buttons.
[BEEP OFF] Disable the
beep sound
of buttons.
[DIMMER] [DIMMER HIGH] Increase the
brightness
level of the
screen.
[DIMMER LOW] Decrease the
brightness
level of the
screen.
[DEMO] [DEMO ON] Demonstrate
all features
after the
system stays
inactive for 2
minutes.
[DEMO OFF] Disable the
demo mode.