Philips CID3281/93 User manual

www.philips.com/welcome
Register your product and get support at
ENG Quick Start Guide
CID3281

1
3

1
a
b
cd
e f
Yellow Green Blue
Red
Black
Yellow
Yellow
Blue/white
Pink
Green/white
White/
brown
Orange/
white
Purple
Purple/black
White/black
Orange/white
Brown/black
Brown
Red
Green/black
Grey/black
White
Green
Grey
Brown/
black
Gearbox
Black
Yellow
AV system AV system
AUX AUX
Red
Red
White
White
Yellow
Yellow
Optional accessory
Optional accessory
GPS antenna
Radio antenna
Rear display
Rear display
Yellow Yellow
Amplifier
White
White
Red
Red
Brown
Note: 1. If there is built-in CAN, connect cto d. No need to do the connections as
indicated in a, eand f.
2. If there is not built-in CAN, you need to:
i) Connect dto b(no need to connect c). ii) Connect the wires as indicated in a. iii) Connect eto f.

4

English
Install the car audio
These instructions are for a typical installation.
However, if your car has different requirements,
make the corresponding adjustment. If you have
any questions regarding installation kits, consult
your Philips car audio dealer.
Caution
This unit is designed for negative ground

(earth) 12 V DC operation only.
Always install this unit in the car dashboard.

Other locations can be dangerous as the
rear of the unit heats up during use.
To avoid short-circuit: before you connect,

ensure that the ignition is off.
Ensure that you connect the yellow and red

power supply leads after all other leads are
connected.
Ensure that all loose leads are insulated with

electrical tape.
Ensure that the leads do not get caught

under screws orin parts that will move
(e.g. seat rail).
Ensure that all ground (earth) leads are run

to a common ground (earth) point.
Use only the supplied mounting hardware

for a safe and secure installation.
,PSURSHUIXVHVFDQFDXVHGDPDJHRUÀUH

When you need to change the fuse, consult
a professional.
Note on the power supply lead (yellow)
When you connect other devices to this
system, ensure that the rating of the car
circuit is higher than the total fuse value of
all the connected devices.
Notes on speaker connection
Never connect speaker wires to the metal
body or chassis of the car.
Never connect speaker wires with stripes
to one another.
Mount in the dashboard 1
Note
Check wire connection before you mount
the unit into a car.
If preset radio stations are lost when the

ignition key is turned OFF and then back ON,
reconnect the red leads crosswise to the
yellow ones.
1If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car battery.
If you disconnect the car battery in
a car that has an on-board drive or
navigation computer, the computer
may lost its memory.
If the car battery is not disconnected,
to avoid short-circuit, ensure that bare
wires do not touch each other.
2Take out the original car audio and keep
the screws.
3Connect wires (see “Connect wires”
section).
4Slide the unit into the dashboard until a
click sound is heard.
5Fix the unit onto the dashboard with
screws.
6Reconnect the negative terminal of the car
battery.
Connect wires 2
Caution
Ensure that all loose leads are insulated with

electrical tape.
1Check the car’s wiring carefully, then do the
other connections:

Turn on
Caution
Risk of road accidents! Never watch video or

adjust settings while you drive.
1Press to turn on the unit.
The available OSD (On-Screen Display)»
languages are displayed.
2Touch a language to select.
The OSD language is changed to the»
selected language immediately.
To turn off the unit, press for 3 seconds.
Set date and time
1Touch the upper left corner to display main
menu.
If necessary, touch in the middle right
side of the screen to display the 2nd
screen.
2Touch [Settings].
3Touch [Time].
The date/time setup menu is displayed.»
Set date
1Touch [Date].
2Touch on the displayed date information.
»A submenu is displayed.
3Touch or to set year, month and day.
Set clock mode
1Touch [Time mode].
2Touch on [12H] or[24H] to select clock
mode.
Set time
1Touch [Time].
2Touch on the displayed time.
A submenu is displayed.»

3Touch or to set hour and minute.
Tip
When date/time is set, touchto return to
main menu.
Adjust screen
To turn off the screen
1Press DISP for over 2 seconds
The screen is turned off.»
To turn on the screen, press»DISP.
To adjust screen brightness
1Press DISP.
Brightness bar is displayed.»
2Rotate TUNE/ SELECT to adjust the
value.
Use map
Note
You may need to upgrade the navigation map

before using it (see “Upgrade the navigation
map” section)
1Touch the upper left corner to display home
menu.
2Touch [Navigation].
The navigation menu is displayed in a»
few seconds.
3Refer to the user manual of the navigation
map to operate the navigation tool.
Tip
You can pressNAVI to enter/exit the navigation
system.
Listen to Radio
1Touch the upper left corner to display
home menu.
2Touch [Radio].
Band and frequency information is»
displayed.

3Touch on FM or AM to select band:
FM band options: FM1, FM2, FM3
AM band options: AM1, AM2
4 %ULHÁ\WRXFK or to tune to a radio
station by step.
Touch or for over 1 seconds to
tune to a radio station automatically.
Play disc 3
You can play video, audio or images stored on the
following discs:
DVD video, DVD-R, DVD-RW
VCD
Audio CD, CD-R, CD-RW
Note
Ensure that the disc contains playable content.
You can play DVD discs with the following region
codes:
DVD region code Country
China
1Insert the disc into the disc slot with label
side facing up.
Play starts automatically.»
To remove the disc, press the»button.
When the disc is ejected, the unit
»
switches to the previous source,
if connected. Otherwise, the
unit switches to [Radio] mode
automatically.
Play USB device 4
Note
Ensure that the device contains playable content
1Open the USB door.
2Connect the USB device to the unit with
the supplied USB cable.
»Play starts automatically.
Note
To remove the USB device, switch to disc,

UDGLRRURWKHUVRXUFHÀUVW
Play with Bluetooth device
Pair the Bluetooth-enabled devices
To connect your Bluetooth device to the unit, you
need to pair the device to the unit. Pairing needs
only to be done once.
You can pair up to eight devices.
1Search for Bluetooth device with the
device.
2Select “CID3281” in the pairing list.
3Enter default password “0000”.
if pairing succeeds. phone call record is»
displayed.

© 2010 Koninklijke Philips Electronics N.V.
All rights reserved.
CID3281_93_QSG_V1.0
Make a call
1Pair the phone with the unit.
2Touch the upper left corner to display the
home menu.
3Touch [Bluetooth].
The Bluetooth menu is displayed.»
4Touch or to select the paired phone,
then touch .
5Touch or to search for phone number
from the following list:
Or touch to dial number directly, then touch
to dial.
Receive call
By default, all incoming calls are received
automatically.
1If there is incoming call, [Incoming call...]
ÁDVKHVRQWKHVFUHHQ6SHDNLQWRWKH
Bluetooth microphone.
2When conversation ends, touch (red)
to terminate the call.
Tip
You can select to receive calls manually by
set [Auto answer] to [Off]status.