Philips Senseo HD7858 User manual

HD7858, HD7857,
HD7856, HD7855
User manual
Benutzerhandbuch
Mode d’emploi
Gebruiksaanwijzing

1

2
6
10
14
18
3
7
11
15
19
4
8
12
16
20
5
9
13
17
2xx
21

5
2 General
description (Fig. 1)
1 1-cup pod holder q
2 2-cup pod holder qq
3 Coffee collector
4 Coffee spout
5 Milk spout
6 Milk tube
7 Cup tray
8 Removable drip tray
9 Water reservoir
10 Touch panel with recipe buttons
11 CALC button
12 Café Latte button
13 Latte Macchiato button
14 Cappuccino button
15 Cup indicators
16 On/off button
17 Regular coffee button
18 Strong coffee button
19 Milk only button
3 Important
Read this user manual carefully before
you use the machine and save it for
future reference.
Danger
•Never immerse the machine in
water or any other liquid.
Warning
•Check if the voltage indicated on the
bottom of the machine corresponds
to the local mains voltage before
you connect the machine.
•This machine can be used by
children aged from 8 years and
above and by persons with
reduced physical, sensory or
mental capabilities or lack of
1 Introduction
Congratulations on your purchase and welcome
to Philips! To fully benet from the support that
Philips offers, register your product at
www.philips.com/welcome.
1.1 SENSEO®coffee system
Make your coffee moments truly special with
SENSEO®.This unique system combines the
easy-to-use Philips SENSEO®coffee machine
with the specially developed D.E Master Blenders
SENSEO®coffee pods, giving you a full, smooth
coffee with a delicious foam layer.
D.E Master Blenders coffee in convenient
SENSEO®coffee pods and Philips’ unique new
SENSEO®brewing system are perfectly matched
to ensure that the best taste and aroma are
extracted from the coffee. Discover all SENSEO®
coffee blends at www.senseo.com.
To ensure a smooth and full coffee taste, you
should keep the following things in mind:
Fresh coffee pods
Use the SENSEO®coffee pods that have been
specially developed by D.E Master Blenders for
your SENSEO®coffee machine for a full, round
taste. D.E Master Blenders SENSEO®coffee
pods stay fresh longer if you store them in an
airtight storage container.
Fresh water
Use fresh water every day. If you have not used
the coffee machine for one day, you have to ush
it with fresh water before you use it again.
ENGLISH

6
•Do not place the machine on a
hotplate, directly next to a hot
oven or similar source of heat.
•Do not keep the machine at
temperatures below 0°.Water left
in the heating system may freeze
and cause damage.
•Never pour milk, coffee, hot water
or carbonated water into the
water reservoir.
•Never put normal ground coffee
or use torn pods in the machine, as
this causes it to become blocked.
•Never ush the machine or let it
brew coffee when the spout is not
in place.
•This machine is intended for
normal household use only.
It is not intended for use in
environments such as staff
kitchens of shops, ofces, farms
or other work environments.
Nor is it intended to be used by
clients in hotels, motels, bed and
breakfasts and other residential
environments.
3.1 Compliance with standards
This Philips machine complies with all applicable
standards and regulations regarding exposure to
electromagnetic elds.
The energy consumption of this machine in
off mode is less than 0,5 watt.This means that
this machine complies with European Directive
2009/125/EC, which sets the ecological design
requirements for energy-using products.
experience and knowledge if they
have been given supervision or
instruction concerning use of the
machine in a safe way and if they
understand the hazards involved.
•Cleaning and user maintenance shall
not be made by children unless they
are older than 8 and supervised.
•Keep the machine and its cord out
of the reach of children aged less
than 8 years.
•Children should be supervised to
ensure that they do not play with
the machine.
•Do not use the machine if the
plug, the mains cord or the
machine itself is damaged.
•If the mains cord is damaged, you
must have it replaced by Philips,
a service centre authorised
by Philips or similarly qualied
persons in order to avoid a hazard.
Caution
•Always return the machine to
a service centre authorised by
Philips for examination or repair.
Do not attempt to repair the
machine yourself, otherwise your
guarantee becomes invalid.
•Do not use the machine in
combination with a transformer,
as this could cause hazardous
situations.
•Always put the machine on a
at and stable surface. Keep it
in upright position, also during
transport.

7
5 Brewing black
SENSEO®coffee
1 Make sure that the water reservoir is lled
with fresh cold tap water (Fig. 3).
ETip:
Use fresh water every day.
2 Put the plug in an earthed wall socket.
3 Press the on/off button.The on/off button
ashes slowly while the water heats up. (Fig. 8)
DNote:
If the on/off button ashes rapidly, the water
reservoir does not contain enough water for
brewing one cup of coffee.
4 Pull the lid lever upwards to open the
lid. (Fig. 12)
5 If you want to make one cup of SENSEO®
coffee, place the 1-cup pod holder qin
the machine (1). If you want to make two
cups, put the 2-cup pod holder qq in the
machine (2). Make sure the pod holder is
clean. (Fig. 13)
6 Place 1 coffee pod in the 1-cup pod holder q
(1) or place 2 coffee pods in the 2-cup pod
holder qq (2). Place the pod or pods properly
in the centre of the pod holder, with the
convex side pointing downwards. Press the pod
or pods lightly into the pod holder. (Fig. 14)
DNote:
Make sure the coffee in the pod or pods is
evenly distributed.
CCaution:
Never put normal ground coffee or use torn
pods in the SENSEO®machine, as this causes
it to become blocked.
7 Close the lid and lock the lever. (Fig. 15)
BWarning:
Make sure the lid is closed properly and the
lid lever is locked before you start brewing
coffee.
4 Flushing the
machine before rst
use
It is important that you ush your SENSEO®coffee
machine before rst use. After the ushing cycle,
the machine is ready for brewing SENSEO®coffee.
CCaution:
Never interrupt the ushing cycle halfway. If you
do, the boiler does not ll itself properly.
1 Tilt the water reservoir backwards (1) and lift
the water reservoir off the machine (2) (Fig. 2).
2 Fill the water reservoir. (Fig. 3)
3 Tilt the water reservoir and place the bottom
back onto the machine (1).Then press the top
of the water reservoir towards the machine
(2) (Fig. 4).
4 Slide the milk spout onto the machine. Make
sure you attach the milk spout by sliding it
over the guiding rails on the coffee spout.You
hear a click sound when the spout is attached
properly (Fig. 5).
5 Place a bowl with a capacity of at least 1 litre
under the coffee spout. (Fig. 6)
6 Make sure a pod holder, without pod or pods,
is in place. (Fig. 7)
7 Put the plug in an earthed wall socket.
8 Press the on/off button.The button lights
up to indicate that you have to ush the
machine. (Fig. 8)
9 To start ushing, press any of the recipe
buttons. (Fig. 9)
•
During the ushing cycle, the boiler lls itself
with water from the water reservoir and cold
water comes out of the coffee spout. During the
ushing cycle, the machine produces more noise
than during a regular brewing cycle (Fig. 10).
•When all the water in the water reservoir
has been used up, the ushing cycle is
nished and the machine switches off. You
may notice some steam coming from the
machine, this is normal (Fig. 11).
10 Fill the water reservoir with fresh tap water
and place it back onto the machine.
ENGLISH

8
6 Brewing a coffee
speciality with fresh
milk
With the SENSEO®coffee machine you can easily
create the perfect cappuccino, café latte, latte
macchiato or warm milk only with two cups at the
same time.
1 Make sure that the water reservoir is lled
with fresh cold tap water (Fig. 3).
ETip:
Use fresh water every day.
2 Put the plug in an earthed wall socket.
3 Press the on/off button.The on/off button
ashes slowly while the water heats up. (Fig. 8)
DNote:
If the on/off button ashes rapidly, the water
reservoir does not contain enough water for
brewing one cup of coffee.
4 Pull the lid lever upwards to open the
lid. (Fig. 12)
5 If you want to make one cup of cappuccino,
café latte or latte macchiato, place the 1-cup
pod holder qin the machine (1). If you want
to make two cups, put the 2-cup pod holder
qq in the machine (2). Make sure the pod
holder is clean. (Fig. 13)
DNote:
For warm milk only, you do not have to place a
pod holder in the machine. Proceed with step 7.
6 Place 1 coffee pod in the 1-cup pod holder
q(1) or place 2 coffee pods in the 2-cup
pod holder qq (2). Place the pod or pods
properly in the centre of the pod holder,
with the convex side pointing downwards.
Press the pod or pods lightly into the pod
holder. (Fig. 14)
DNote:
Make sure the coffee in the pod or pods is
evenly distributed.
8 Place one cup or two cups under the spout
openings. Use the markings on the drip tray to
place the cup or cups (Fig. 16).
DNote:
You can adjust the height of the drip tray
or remove the drip tray to be able to place
higher cups.
DNote
The cups you use should have a capacity of at
least 150ml when you brew regular coffee or
100ml when you brew strong coffee. Do not
use cups that are too large, as they cause the
coffee to get cold more quickly.
9 Press the button with two coffee beans for
a regular cup of coffee. Press the button
with three coffee beans for a strong cup of
coffee (Fig. 17).
10 Press the recipe button once for one cup of
coffee or twice for two cups of coffee.
11 When the water has heated up and the on/
off button lights up continuously, the machine
automatically starts brewing coffee.
DNote:
Do not remove the water reservoir during a
brewing cycle.
12 When the coffee is ready, remove the used
coffee pod or pods. Simply lift the pod holder
out of the machine and empty it.
CCaution:
There may still be some hot water/coffee on
the coffee pod or pods.
13 After use, press the on/off button to switch
off the machine. (Fig. 18)
DNote:
If you do not use the machine, it switches off
automatically after 15 minutes to save energy.

9
13 When the coffee is ready, remove the used
coffee pod or pods. Simply lift the pod holder
out of the machine and empty it.
CCaution:
There may still be some hot water/coffee on
the coffee pod or pods.
14 Remove the milk spout and tube from
the machine and clean them (see chapter
‘Cleaning the milk spout’ and the illustrations
on the fold-out cover).
15 After use, press the on/off button to switch
off the machine. (Fig. 18)
DNote:
If you do not use the machine, it switches off
automatically after 15 minutes to save energy.
7 Adjusting the coffee
volume
7.1 Adjusting the coffee volume
to your personal taste
DNote:
This feature is only available for typenumbers
HD7858 and HD7857.
You can adjust the volume of each recipe to your
own personal taste by programming the different
recipes.
1 Switch on the appliance (Fig. 8).
2 Fill the water reservoir with cold water up to
the MAX indication.
3 Put a coffee pod in the pod holder.
4 If you want to prepare a coffee speciality with
milk, put the tube of the milk spout into a
carton or jar of milk.
5 Press the CALC button and the button for
the recipe you want to adjust simultaneously.
Release the buttons when the appliance
beeps twice after approximately two
seconds (Fig. 23).
CCaution:
Never put normal ground coffee or use torn
pods in the SENSEO®machine, as this causes
it to become blocked.
7 Close the lid and lock the lever. (Fig. 15)
BWarning:
Make sure the lid is closed properly and the
lid lever is locked before you start brewing
coffee.
8 Slide the milk spout onto the machine. Make
sure you attach the milk spout by sliding it
over the guiding rails on the coffee spout.You
hear a click sound when the spout is attached
properly (Fig. 5).
9 Insert the connector of the milk tube into the
milk spout (1). Place the other end of the milk
tube in a milk carton or jar (2) (Fig. 19).
ETip:
Use fresh chilled milk.We recommend semi
skimmed fresh cow’s milk to get the best milk
froth.
DNote:
To prevent steaming from coming out of the
milk spout, make sure there is enough milk in
the carton or jar.
10 Place one cup or two cups under the spout
openings.You can adjust the drip tray or
remove the drip tray to be able to place
higher cups.
11 Press the recipe button of your choice to
select the desired coffee speciality.You can
choose between cappuccino, café latte, latte
macchiato or warm milk only. Press the recipe
button once for one cup or twice for two
cups (Fig. 20).
12 When the water has heated up and the on/
off button lights up continuously, the machine
starts to create the selected coffee speciality
with milk. (Fig. 22)
DNote:
The machine rst brews milk and then adds
the coffee. In case of café latte, the machine
rst adds coffee and then brews milk.
ENGLISH

10
8.1.2 After the last use of the day
Clean the milk tube and the milk spout in the
dishwasher or in hot water with some washing-up
liquid.
DNote:
Cleaning in the dishwasher is recommended.
1 Pull the milk tube out of the milk
spout (Fig. 28).
2 To remove the milk spout from the machine,
pull it towards you (Fig. 29).
3 Remove the top part of the milk spout from
the bottom part by pulling it rmly. (Fig. 30)
4 Take out the frothing system (Fig. 31).
5 Open the spring to separate the
parts (Fig. 32).
6 Remove the inside part of the frothing system
by pulling it downwards (Fig. 33).
7 Remove the small lid by pulling it
upwards (Fig. 34).
8 Clean all parts in the dishwasher or with hot
water and some washing-up liquid (Fig. 35).
8.1.3 Reassembling the milk spout
1 Place the small lid back on the frothing
system (Fig. 36).
2 Place the inside part back into the frothing
system (Fig. 37).
3 Close the spring to lock the two parts
together (Fig. 38).
4 Place the frothing system in the bottom part
of the milk spout (Fig. 39).
5 Place the top part of the milk spout back
onto the bottom part (Fig. 40).
8.2 Cleaning the coffee spout
and the machine
1 Always unplug the machine before you clean it.
2 To remove the coffee spout from the
machine, pull it towards you (Fig. 41).
3 Remove the top part of the coffee spout from
the bottom part by pulling it rmly (Fig. 42).
4 Clean the outside of the machine with a moist
cloth.
5 Clean the water distribution disc and the
rubber sealing ring with a moist cloth.
•The 1-cup symbol starts to ash.
6 Press one of the following buttons to change
the coffee volume: the regular coffee button
for a larger cup, the milk only button for a
medium cup (default setting) or the strong
coffee button for a smaller cup (Fig. 24).
•The appliance beeps three times to conrm
and starts to brew a coffee recipe according
to the new setting.
The appliance saves the setting automatically.
8 Cleaning
Regular cleaning of your SENSEO®is important
to ensure that the SENSEO®coffee always tastes
optimally and to optimise the lifetime of the
coffee machine.
BWarning:
Never immerse the SENSEO®coffee machine in
water.
8.1 Cleaning the milk spout
For a reliable performance of the milk spout
and consistently good frothing results, it is
important to clean the milk spout and milk tube
regularly and thoroughly.The milk spout can be
disassembled completely, which allows you to
remove all milk residues from it.
DNote:
If you do not plan to froth milk again straight
away, rinse the milk spout and milk tube within 30
minutes after use.
DNote:
After the last use of the day, clean the milk spout
and milk tube thoroughly.
8.1.1 Rinsing after every use
1 Put the milk tube in a cup of clean water (Fig. 25).
2 Place an empty cup under the spout (Fig. 26).
3 Press the milk only button (Fig. 27).
The machine rinses all milk residues from the
milk spout and milk tube with clean hot water.