Philips AJ7050D User manual

www.philips.com/welcome
User manual
Always there to help you
Register your product and get support at
AJ7050D
Question?
Contact
Philips

1
English
EN
Contents
1 Important 2
Safety 2
Notice 3
2 Your Docking Entertainment System 5
Introduction 5
What’s in the box 5
Overview of the main unit 6
3 Get started 8
Install batteries 8
Connect power 8
Turn on 8
Switch to standby 9
Set time and date 9
4 Play 10
Play from iPod/iPhone/iPad 10
Play from an external device 10
5 Listen to radio 11
Tune to a radio station 11
Program radio stations 11
6 Other features 12
Set the alarm timer 12
Set the sleep timer 13
Adjust display brightness 13
7 Adjust sound 14
Adjust volume level 14
Select a sound effect 14
8 Product information 15
Specications 15
9 Troubleshooting 16
Contents

2EN
1 Important
Safety
Know these safety symbols
This ‘bolt of lightning’ indicates uninsulated
material within your unit may cause an electrical
shock. For the safety of everyone in your
household, please do not remove product
covering.
The ‘exclamation point’ calls attention to
features for which you should read the enclosed
literature closely to prevent operating and
maintenance problems.
WARNING:Toreducetheriskofreorelectric
shock, this apparatus should not be exposed to
rainormoistureandobjectslledwithliquids,
such as vases, should not be placed on this
apparatus.
CAUTION:To prevent electric shock, match
wide blade of plug to wide slot, fully insert.
Important Safety Instructions
a Read these instructions.
b Keep these instructions.
c Heed all warnings.
d Follow all instructions.
e Do not use this apparatus near water.
f Clean only with dry cloth.
g Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
h Do not install near any heat sources such
as radiators, heat registers, stoves, or
other apparatus (including ampliers) that
produce heat.
i Protect the power cord from being
walked on or pinched, particularly at
plugs, convenience receptacles, and the
point where they exit from the apparatus.
j Only use attachments/accessories
specied by the manufacturer.
k Unplug this apparatus during lightning
storms or when unused for long periods
of time.
l Refer all servicing to qualied service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.
m Battery usage CAUTION – To prevent
battery leakage which may result in bodily
injury, property damage, or damage to
the unit:
• Install all batteries correctly, + and - as
marked on the unit.
• Do not mix batteries (old and new or
carbon and alkaline, etc.).
• Remove batteries when the unit is not
used for a long time.
• Batteries (battery pack or batteries
installed) shall not be exposed to
excessiveheatsuchassunshine,reor
the like.

3
English
EN
n Apparatus shall not be exposed to
dripping or splashing.
o Do not place any sources of danger on
the apparatus (e.g. liquid lled objects,
lighted candles).
p Where the MAINS plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
Important notes for users in the U.K.
Mains fuse
This information applies only to products with a
UK mains plug.
Thisproductisttedwithanapprovedmolded
plug. If you replace the fuse, use one with:
• the ratings shown on the plug,
• a BS 1362 approval, and
• the ASTA approval mark.
Contact your dealer if you are not sure about
what type of fuse to use.
Caution:To conform with the EMC directive
(2004/108/EC), do not detach the plug from
the power cord.
How to connect a plug
The wires in the power cord are colored as
follows: blue = neutral (N), brown = live (L).
If the colors do not correspond with the colors
on your plug, identify the terminals in your plug
as follows:
1 Connect the blue wire to the terminal
marked N or colored black.
2 Connect the brown wire to the terminal
marked L or colored red.
3 Do not connect either wire to the earth
terminal in the plug, marked E (or e) or
colored green (or green and yellow).
Before you replace the plug cover, make sure
that the cord grip is clamped over the sheath
of the cable and not just over the two wires in
the cable.
Copyright in the U.K.
Recordingandplaybackofmaterialmayrequire
consent. see Copyright Act 1956 and The
performer’s Protection Acts 1958 to 1972.
Warning
•Never remove the casing of this apparatus.
•Never lubricate any part of this apparatus.
•Never place this apparatus on other electrical
equipment.
•Keep this apparatus away from direct sunlight, naked
amesorheat.
•Ensure that you always have easy access to the power
cord, plug or adaptor to disconnect the apparatus from
the power.
Notice
This product complies with the radio
interferencerequirementsoftheEuropean
Community.
Anychangesormodicationsmadetothis
device that are not expressly approved by
WOOX Innovations may void the user’s
authoritytooperatetheequipment.
Specicationsaresubjecttochangewithout
notice.WOOX reserves the right to change
products at any time without being obliged to
adjust earlier supplies accordingly.
Your product is designed and manufactured
withhighqualitymaterialsandcomponents,
which can be recycled and reused.
When this crossed-out wheeled bin symbol is
attached to a product it means that the product
is covered by the European Directive 2002/96/
EC.

4EN
Please inform yourself about the local separate
collection system for electrical and electronic
products.
Please act according to your local rules and
do not dispose of your old products with your
normal household waste. Correct disposal of
your old product helps to prevent potential
negativeconsequencesfortheenvironmentand
human health.
Your product contains batteries covered by
the European Directive 2006/66/EC, which
cannot be disposed with normal household
waste.Please inform yourself about the local
rules on separate collection of batteries
because correct disposal helps to prevent
negativeconsequencesfortheenvironmental
and human health.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by
a specialized company. Please observe the
local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
“Made for iPod,”“Made for iPhone,” and “Made
for iPad” mean that an electronic accessory
hasbeendesignedtoconnectspecicallyto
iPod, iPhone, or iPad, respectively, and has
beencertiedbythedevelopertomeet
Apple performance standards. Apple is not
responsible for the operation of this device
or its compliance with safety and regulatory
standards. Please note that the use of this
accessory with iPod, iPhone, or iPad may affect
wireless performance.
iPod and iPhone are trademarks of Apple Inc.,
registered in the U.S. and other countries. iPad
is a trademark of Apple Inc.
Class II equipment symbol:
CLASS II apparatus with double insulation, and
no protective earth provided.
Note
•The type plate is located on the bottom of the unit.

5
English
EN
2 Your Docking
Entertainment
System
Congratulations on your purchase, and
welcometoPhilips!Tofullybenetfromthe
support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
With this unit, you can enjoy music from your
iPod/iPhone/iPad and listen to radio or other
audio devices.
Your iPod/ iPhone/iPad and radio can be set as
alarm sources.You can set two alarms to go off
at different time.
You can enrich sound output with these sound
effects:
• Digital Sound Control (DSC)
• Dynamic Bass Boost (DBB)
What’s in the box
Check and identify the contents of your
package:
• Main unit
• Printed materials

6EN
Overview of the main unit
a FM antenna
b AUDIO IN
• Connect an external audio device.
c USB charging port
• Charge a portable device (such as
your 30-pin Apple device or MP3
player etc.) through a USB cable (not
supplied).
d Power cord
e Dock for iPod/iPhone/iPad with Lightning
connection
f TUNE+/TUNE- ( / )
• During clock setting in standby mode,
set the time format and adjust the
hour/minute.
abcd
e
f
g
h
i
j
k
q
p
o
n
m
l
• During alarm setting, adjust the alarm
clock and volume, and select a sound
source.
• Tune to an FM audio station.
g OK/
• In dock mode, start or pause iPod/
iPhone/iPad play.
• In FM mode, select FM stereo or FM
mono.
• ConrmmanualprogrammingofFM
radio stations.
h PRESET +/PRESET - ( / )
• Skip to next/previous track.
• Select a preset radio program.
• In dock mode, press and hold to fast
forward/backward.

7
English
EN
i SOURCE
• Select a source: DOCK, FM or AUDIO
IN.
j AL1/AL2
• Set alarm.
• View alarm settings.
• Activate/deactivate alarm timer.
k Display panel
• Show the current status.
l SNOOZE/BRIGHTNESS
• Snooze alarm.
• Adjust the display brightness.
m
• Turn on the unit or switch to standby
mode.
• Stop alarm.
n PROG/SCAN ( )
• Program radio stations.
• Automatically scan for radio stations.
• In dock mode, press and hold to fast
forward.
o SET TIME ( )
• In standby mode, set month, day and
year.
• In other modes, enable/disable either
DBB (Dynamic Bass Boost) or DSC
(Digital Sound Control) sound effect.
• In dock mode, press and hold to fast
backward.
p SLEEP
• Set the sleep timer.
q VOL +/VOL - ( / )
• Increase/decrease volume.

8EN
3 Get started
Caution
•Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
radiation exposure or other unsafe operation.
Always follow the instructions in this chapter in
sequence.
If you contact Philips, you will be asked for the
model and serial number of this apparatus.The
model number and serial number are on the
bottom of the apparatus.Write the numbers
here:
Model No. __________________________
Serial No. ___________________________
Install batteries
Note
•You can only use AC power as power supply. Batteries
(not supplied) are for backup purpose.
1 Open the battery compartment.
2 Insert 2 x AAA size batteries with correct
polarity (+/-) as indicated.
3 Close the battery compartment.
Caution
•Risk of explosion! Keep batteries away from heat,
sunshineorre.Neverdiscardbatteriesinre.
•Risk of decreased battery life! Never mix different
brands or types of batteries.
•Risk of product damage! When the remote control is
not used for long periods, remove the batteries.
Connect power
Caution
•Risk of product damage! Ensure that the power voltage
corresponds to the voltage printed on the bottom of
the apparatus.
•Risk of electric shock! When you unplug the AC power
cord, always pull the plug from the socket. Never pull
the cord.
•Before connecting the AC power cord, ensure you have
completed all other connections.
•To disconnect the set from the mains completely,
remove the mains plug from the wall socket.
• Connect the AC power cord to the wall
outlet.
Turn on
• Press .
» The unit switches to the last selected
source.
AC ~
FM
ANTENNA
N I O I D U A
5
V
1 . 2
A

9
English
EN
Switch to standby
• Press again to switch the unit to standby
mode.
» The time and date (if set) appear on
the display panel.
Set time and date
1 In standby mode, press and hold SET TIME
for 2 seconds.
» [24H ] begins to blink, and you can
hear a beep.
2 Press TUNE+ or TUNE- to select the
12/24 hour format.
3 Press OKtoconrm.
» 00:00 will display, and the hour digits
begin to blink.
4 Repeat steps 2-3 to set the hour, minute,
month, day and year.
Tip
•In 12 hour format, [MONTH--DAY] is displayed.
•in 24 hour format, [DAY--MONTH] is displayed.
Note
•When iPod/iPhone/iPad is connected, the docking
unit synchronizes time from the iPod/iPhone/iPad
automatically.

10 EN
4 Play
Play from iPod/iPhone/iPad
You can enjoy audio from iPod/iPhone/iPad
through this unit.
Compatible iPod/iPhone/iPad
The unit supports the following iPod, iPhone,
and iPad models:
Made for:
• iPod nano (7th generation)
• iPod touch (5th generation)
• iPad (4th generation)
• iPad mini
• iPhone 5
Listen to the iPod/iPhone/iPad
1 Press SOURCE repeatedly to select the
DOCK source.
2 Load the iPhone/iPod/iPad.
• To pause/resume play, press .
• To skip to a track, press / .
• To search during play, press and hold
/ or PRESET +/PRESET -, then
release to resume normal play.
Charge the iPod/iPhone/iPad
When the unit is connected to power, the
docked iPod/iPhone/iPad begins to charge.
Tip
•For certain iPod models, it may take up to a minute
before the charging indication appears.
Play from an external device
You can also listen to an external audio device
through this unit.
1 Press SOURCE repeatedly to select the
AUDIO IN source.
2 Connect a 3.5mm audio link cable (not
supplied) to:
• the AUDIO IN jack (3.5mm) on the
back of the unit.
• the headphone jack on an external
device.
» the screen displays scrolling text
message [AUDIO IN] and the current
time.
3 Start to play the device (see the device
user manual).

11
English
EN
5 Listen to radio
Note
•Only FM radio reception is available on this unit.
Tune to a radio station
Tip
•For optimal reception, fully extend and adjust the
position of the FM antenna.
•Position the antenna as far as possible from TV,VCR or
other radiation source.
•[STEREO] is the default setting for tuner mode.
•In tuner mode, you can press OK/ to toggle
between [STEREO] and [MONO], and the unit
memorizes your setting even if you turn off the unit or
turn to other sources.
1 Press SOURCE repeatedly to select FM
mode.
2 Press and hold TUNE+/TUNE- for more
than 2 seconds.
» The radio tunes to next station with
strong reception automatically.
3 Repeat step 2 to tune to more stations.
• To tune to a weak station, press
TUNE+/TUNE- repeatedly until you
ndoptimalreception.
Program radio stations
Radio station preset allows you to save radio
stations,andquicklytunetoafavoritestation.
Note
•The preset list can store up to 20 stations.
•If the preset list is fully occupied, the screen will show
[FULL] (full).
•When you save a radio station to a position that has
already been occupied, the original radio station will
be replaced.
Program radio stations manually
1. Press SOURCE repeatedly to enter the FM
mode.
2. Press TUNE+/TUNE- to tune to a radio
station.
3. Press PROG/SCAN.
» Apositionnumberashes.
4. Press OK to save current radio station to the
selected position.
Tip
•Press PRESET +/PRESET - to change the position to
save a radio station.
Program radio stations automatically
1 Press SOURCE repeatedly to enter the
FM mode.
2 Press and hold PROG/SCAN.
» The screen displays [AUTO] (auto);
» The unit starts to scan for all available
radio stations automatically, and stores
them to the preset list.
3 Waituntiltheautoscannishes.
» Therststationinthepresetlist
broadcasts automatically.
Select a preset radio station
1 Press / to select a preset number.

12 EN
6 Other features
Set the alarm timer
You can set two alarms at different times.
Note
•Ensure that you have set the clock correctly.
1 Press and hold AL1 or AL2.
» The hour digits begin to blink, and you
can hear one beep.
» [ALSET](alarmset)ashesonthe
screen.
2 Press TUNE+/TUNE- repeatedly to set
the hour.
3 Press OKtoconrm.
» The minute digits begin to blink.
» [ALSET](alarmset)ashesonthe
screen.
4 Repeat steps 2-3 to set the minute, select
when to ring alarm, and choose alarm
sound source and alarm volume.
After alarm volume is set, the unit will exit
alarm setting, and you can hear two beeps.
Tip
•If you select DOCK as the alarm sound source, when
there is no device docked, the alarm will automatically
switch to buzzer to ring the alarm.
•If both alarms are set to the same time, only Alarm 1
will ring.
View the alarm settings
Press AL1 or AL2 to view alarm settings.
Activate and deactivate the alarm
timer
When an alarm setting is shown on the screen,
press AL1/AL2 repeatedly to activate or
deactivate the timer.
» If the timer is activated, [ AL 1] or [
AL2] is displayed.
» If the timer is deactivated, [ AL1] or
[ AL2] disappears.
Snooze
When the alarm rings, press SNOOZE.
» The alarm stops, and the alarm icon
ashes.
» The alarm will resume ringing 9
minutes later.
Note
•When using batteries to operate, alarms can only use
buzzer as sound source.
Stop alarm ring
When the alarm rings, press the corresponding
AL1 or AL2.
» The alarm stops but the alarm settings
remain.
Tip
•You can also press to stop the alarm.The unit will
switch to the last selected source.
•If you press and hold , the alarm will also be stopped,
and the unit will switch to standby mode.
•If you do not stop the alarm, it will ring for 30 minutes.
•When an alarm rings, it shall begin from a relative low
volume, and rise gradually to the highest alarm volume
in 90 seconds.

13
English
EN
Set the sleep timer
This unit can switch to standby automatically
after a set period of time.
Press SLEEP repeatedly to select from 120, 90,
60, 45, 30 and 15 minutes.
» When the sleep timer is activated, the
display shows .
To deactivate sleep timer
1 Press SLEEP repeatedly until [OFF] (off) is
displayed.
» The sleep timer is deactivated,
disappears on the display.
Adjust display brightness
Whennoalarmisring,pressBRIGHTNESS
repeatedly to select different levels of display
brightness.
Note
•When using batteries to operate, you can not select
brightness levels.

14 EN
7 Adjust sound
Adjust volume level
During play, press VOL +/- to increase/decrease
the volume level step by step.
Tip
•Press and hold VOL +/- to increase/decrease the
volume at faster speed.
Select a sound effect
During play, press SET TIME repeatedly to
select from a preset sound effect and turn on/
off dynamic bass enhancement.
Note
•The unit supports the following sound effects: [POP]
(pop), [JAZZ] (Jazz), [ROCK] (rock), [CLAS] (classic)
and [FLAT](at).
•If DBB is activated, [DBB] is displayed.

15
English
EN
8 Product
information
Note
•Product information is subject to change without prior
notice.
Specications
Amplier
Total output power 2 x 3W RMS
FrequencyResponse 80Hz-16kHz
±3dB
Signal to Noise Ratio ≥67dBA
Aux Input (Audio in) 600mV RMS
22kohm
FM
Tuning Range FM 87.5 -
108 MHz
Tuning grid 50 KHz
- Mono, 26dB S/N Ratio
- Stereo, 46dB S/N Ratio
<22 dBf
<43 dBf
Search Sensitivity <28 dBf
Total Harmonic Distortion <2%
Signal to Noise Ratio >50 dB
Speakers
Speaker Impedance 4 ohm
Speaker Driver 58mm full range
Sensitivity 83dB/1m/1W
General information
AC power 110-240V~,50/60Hz
Operation Power
Consumption
28 W
Standby Power
Consumption (clock
display)
<1 W
Dimensions
- Main Unit (W x H
x D)
260 x 137 x 185 mm
Weight (Main unit,
without packing)
1.13 kg

16 EN
9 Troubleshooting
Caution
•Never remove the casing of this apparatus.
To keep the warranty valid, never try to repair
the system yourself.
If you encounter problems when using this
apparatus, check the following points before
requestingservice.Iftheproblemremains
unsolved, go to the philips web site (www.
philips.com/support).When you contact philips,
ensure that your apparatus is nearby and the
model number and serial number are available.
No power
•Ensure that the AC power plug of the unit
is connected properly.
•Ensure that there is power at the AC
outlet.
•Ensure that the batteries are inserted
correctly.
No sound
•Adjust the volume.
•Check if the unit is performing auto scan.
Volume is muted during auto scan process.
No response from the unit
•Remove the batteries from the main unit
(if inserted), disconnect and reconnect the
AC power plug, and turn on the unit again.
Poor radio reception
•Increase the distance between the unit and
your TV or VCR.
•Fully extend the FM antenna.
Timer does not work
•Set the clock correctly.
•Switch on the timer.
Clock/timer setting erased
•Power has been interrupted or the power
plug has been disconnected.
•Reset the clock/timer.

2014 © WOOX Innovations Limited.
All rights reserved.
This product was brought to the market by WOOX
Innovations Limited or one of its affiliates, further referred
to in this document as WOOX Innovations, and is the
manufacturer of the product.WOOX Innovations is the
warrantor in relation to the product with which this booklet
was packaged. Philips and the Philips Shield Emblem are
registered trademarks of Koninklijke Philips N.V.
AJ7050D_UM_12_V2.0