Philips DVP534K/75 User manual

8239 300 30471
DVDVIDEOPLAYER
DVP532K
DVP534K
DVD
PLAYER
DVD
PLAYER
DVP532K
DVP534K
01-34 DVP532_4K_69 19/03/2004, 2:59 PM1

8239 300 30471
General Information
Environmental Information
All unnecessary packaging has been
omitted.The packaging has been made
easy to separate into three materials:
cardboard (box),polystyrene foam
(buffer) and polyethylene (bags,protective
foam sheet).
Your DVD player consists of materials
which can be recycled and reused if
disassembled by a specialised company.
Please observe the local regulations
regarding the disposal of packaging
materials, exhausted batteries and old
equipment.
Important Note:
Due to the numerous versions of new
CD-Audio copy protection or
enhanced CD-Audio protection
recently available on certain discs,
Philips is unable to guarantee that
this DVD Player is fully compatible
with such new discs. Should you have
difficulty playing any such CD-Audio
discs,kindly refer them to your CD-
Audio disc retailer.
For Customer Use:
Read carefully the information located at
the bottom of your DVDVIDEO player
and enter below the Serial No.Retain this
information for future reference.
Model No. DVP532K
DVP534K
Serial No. _______________
Manufactured under license from Dolby
Laboratories.“Dolby”,“Pro Logic” and the
double-D symbol are trademarks of Dolby
Laboratories.
CAUTION
(WARNING LOCATION:ONTHE
BACKPLATE OFTHE SET)
NEVER MAKE OR CHANGE
CONNECTIONSWITHTHE
POWER SWITCHED ON.
Laser safety
This unit employs a laser.Due to possible
eye injury,only a qualified service person
should remove the cover or attempt to
service this device.
NOTE:
PICTURES SHOWN MAYBE
DIFFERENT BETWEEN
COUNTRIES.
LASER
Type Semiconductor laser
GaAlAs
Wave length 650 nm (DVD)
780 nm (VCD/CD)
Output Power 7 mW (DVD)
10 mW (VCD/CD)
Beam divergence 60 degree
‘CONSUMERS SHOULD NOTETHAT NOT
ALL HIGH DEFINITIONTELEVISION SETS
ARE FULLY COMPATIBLEWITHTHIS
PRODUCT AND MAY CAUSEARTIFACTS
TO BE DISPLAYED INTHE PICTURE. IN
CASE OF 525 OR 625 PROGRESSIVE SCAN
PICTURE PROBLEMS, IT IS RECOMMENDED
THATTHE USER SWITCHTHE
CONNECTIONTOTHE‘STANDARD
DEFINITION’ OUTPUT. IFTHEREARE
QUESTIONS REGARDING OURTV SET
COMPATIBILITYWITHTHIS MODEL 525p
AND 625p DVD PLAYER,PLEASE CONTACT
OUR CUSTOMER SERVICE CENTER.’
The apparatus shall not be exposed to dripping
or splashing and that no objects filled with
liquids, such as vases, shall be placed on
apparatus.
01-34 DVP532_4K_69 19/03/2004, 2:59 PM2

8239 300 30471
3
English
Bahasa Melayu
Manufactured under license from Dolby
Laboratories.“Dolby”,“Pro-Logic” and the
double-D symbol are trademarks of
Dolby Laboratories.
Manufactured under license from Digital
Theater Systems, inc.US Pat. No.
5,451,942 and other worldwide patents
issued and pending. “DTS” and“DTS
Digital Surround”are trademarks of
DigitalTheater Systems, Inc. 1996 Digital
Theater Systems, Inc. All rights reserved.
This product incorporates copyright
protection technology that is protected by
method claims of certain U.S. patents and
other intellectual property rights owned by
Macrovision Corporation and other rights
owners. Use of this copyright protection
technology must be authorized by
Macrovision Corporation,and is intended
for home and other limited viewing uses
only unless otherwise authorized by
Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
English --------------------------------------- 6
-------------------------------- 35
-------------------------------- 67
Bahasa Melayu--------------------------- 99
Index
01-34 DVP532_4K_69 19/03/2004, 2:59 PM3

8239 300 30471
English
4
Introduction
Supplied accessories ....................................... 5
Care and safety information.......................... 5
Connections
ConnectingTV.............................................. 6-7
Using ComponentVideo jacks (Y Pb Pr) .. 6
Using CompositeVideo jack (CVBS) ......... 6
Using S-Video jack.......................................... 7
Using an accessory RF modulator .............. 7
Connecting the power cord.......................... 8
Optional :Connecting to anAudio System..... 8
Stereo system has Dolby Pro Logic or Right
/ LeftAudio In jack ......................................... 8
Optional:Connecting DigitalAV Receiver..... 9
Receiver has a PCM,Dolby Digital,or
MPEG2 decoder.............................................. 9
Functional Overview
Front Panels ....................................................10
DVP532K & DVP534K ................................ 10
Rear Panel .......................................................11
Remote Control ............................................12
Getting Started
Step 1:Inserting batteries into the
Remote Control ............................................13
Using the Remote Control to operate the
Player ...............................................................13
Step 2:Setting up theTV........................13-14
Selecting the colour system that
corresponds to yourTV.............................. 14
Step 3:Setting language preference ...........15
Setting the OSD Language..........................15
Setting theAudio,Subtitle and Disc menu
language .......................................................... 15
Disc Operations
Playable Discs .................................................16
Playing discs.....................................................16
Using the Disc Menu.....................................17
Basic playback controls...........................17-19
Pausing playback............................................ 17
Selecting track/chapter ................................ 17
Resuming playback from the last stopped
point ................................................................ 17
Zoom .............................................................. 18
Repeat ............................................................. 18
RepeatA-B ..................................................... 18
Slow Motion .................................................. 18
Forward / Reverse Searching ..................... 18
Time Search ................................................... 19
Special disc features ................................19-20
Playing aTitle ................................................. 19
CameraAngle ................................................ 19
Changing theAudio Language.................... 19
Subtitles ..........................................................19
Preview Function .......................................... 20
Playing MP3/JPEG Picture CD...............20-21
General Operation.......................................20
Playback selection......................................... 20
Repeat ............................................................. 21
Program playback ......................................... 21
Fast forward / reverse .................................21
Special MP3/JPEG features...........................21
Preview Function (JPEG)............................. 21
Zoom picture (JPEG)................................... 21
Playback with multi-angles (JPEG).............21
Karaoke Operations
Playing Karaoke discs ....................................22
General Operation.......................................22
Key setting......................................................22
Vocal ................................................................22
Mode ...............................................................22
System Menu Options
Basic Operations ...........................................23
General Setup Page .......................................23
Program .......................................................... 23
Screen Saver .................................................. 23
Audio Setup Page.....................................24-26
Speaker Setup ................................................ 24
DigitalAudio Setup.......................................24
Dolby Digital Setup ...................................... 25
Equalizer ......................................................... 25
3D Processing................................................ 26
Video Setup Page .....................................27-29
TV Display ...................................................... 27
Closed Captions ...........................................28
Angle Mark ..................................................... 28
Progressive ..................................................... 28
Smart Picture................................................. 29
Picture Setting ...............................................29
Preference Setup Page............................29-30
Parental .................................................... 29-30
Password ........................................................ 30
Default............................................................. 30
Specifications ......................................31
Troubleshooting ......................... 32–33
Glossary......................................................................34
Contents
01-34 DVP532_4K_69 19/03/2004, 2:59 PM4

8239 300 30471
English
5
Supplied accessories
Remote Control
and
twoAA batteries
Introduction
Care and safety information
●Power consumption
–Check that the operating voltage
indicated on the typeplate (or beside the
voltage selector) is identical to the voltage
of your local power supply.If not,please
consult your dealer.
–When the system is switched to
Standby mode,it is still consuming power.
To disconnect the system from the power
supply completely,remove theAC power
plug from the wall jack.
●Avoid high temperatures,moisture,
water and dust
–Do not expose the player,batteries or
discs to humidity,rain,sand or excessive
heat (caused by heating equipment or
direct sunlight.)
●Avoid condensation problem
– The lens may cloud over when the
player is suddenly moved from cold to
warm surroundings,making it impossible
to play a disc.Leave the player in the
warm environment until the moisture
evaporates.
●Do not block the vents
–Do not operate the DVD Player in an
enclosed cabinet, allow about 10 cm (4
inches) of free space all around the player
for adequate ventilation.
10 cm
(4 inches)
10 cm
(4 inches) 10 cm
(4 inches)
DVD Home Cinema System
PHILIPS
●Care of the cabinet
–Use a soft cloth slightly moistened with
a mild detergent solution. Do not use a
solution containing alcohol, spirits,
ammonia or abrasives.
●Finding a suitable location
–Place the player on a flat,hard,and
stable surface.
●Disc handling
–To clean a CD,wipe it in a
straight line from the center
towards the edge using a soft,
lint-free cloth. A cleaning
agent may damage the disc!
–Write only on the printed side of a
CDR(W) and only with a soft felt-tipped
pen.
–Handle the disc by its edge,do not
touch the surface.
Audio cable
(white,red)
Video cable
(yellow)
PREVIEW
PREVIEW
MUTE
MUTE
VOCAL
VOCAL
MODE
MODE
KARAOKE
KARAOKE
KEY
KEY
01-34 DVP532_4K_69 19/03/2004, 2:59 PM5

8239 300 30471
English
6
Connections
ConnectingTV
Y
VIDEO OUT
S-VIDEO OUT
COAXIAL
MAINS
DIGITAL OUT
L
R
AUDIO OUT
Pb
Pr
COMPONENT
VIDEO OUT
AUDIO
IN
V(Pr/Cr)
U(Pb/Cb)
Y
S-VIDEO
IN
VIDEOIN
COMPONENT
VIDEOIN
AUDIO
IN
V (Pr/Cr)
U (Pb/Cb)
Y
S-VIDEO
IN
VIDEO IN
COMPONENT
VIDEO IN
2
1
IMPORTANT!
–You only need to make one video
connection from the following
options, depending on the
capabilities of yourTV system.
–Connect the DVD system directly
to theTV.
–ComponentVideo connection
provides highest picture quality.
These options must be available on
yourTV.
Using ComponentVideo jack
(Y Pb Pr)
1Use the component video cables (red/
blue/green) to connect the DVD Player’s
Y Pb Pr jacks to the corresponding
Component video input jacks (or labeled
asY Pb Pr orYUV) on theTV (cable not
supplied).
2To hear the sound of this DVD Player
through yourTV,use the audio cables
(white/red) to connectAUDIO OUT (L/
R) jacks of the DVD Player to the
correspondingAUDIO IN jacks on theTV
(cable supplied).
Y
VIDEO OUT
S-VIDEO OUT
COAXIAL
MAINS
DIGITAL OUT
L
R
AUDIO OUT
Pb
Pr
COMPONENT
VIDEO OUT
AUDIO
IN
V(Pr/Cr)
U(Pb/Cb)
Y
S-VIDEO
IN
VIDEOIN
COMPONENT
VIDEOIN
AUDIO
IN
V (Pr/Cr)
U (Pb/Cb)
Y
S-VIDEO
IN
VIDEO IN
COMPONENT
VIDEO IN
2
1
Using CompositeVideo jacks
(CVBS)
1Use the composite video cable (yellow) to
connect the DVD Player’s CVBS (VIDEO
OUT) jack to the video input jack (or
labeled asA/V In,Video In,Composite or
Baseband) on theTV (cable supplied).
2To hear the sound of this DVD Player
through yourTV,use the audio cables
(white/red) to connectAUDIO OUT (L/
R) jacks of the DVD Player to the
correspondingAUDIO IN jacks on theTV
(cable supplied).
01-34 DVP532_4K_69 19/03/2004, 2:59 PM6

8239 300 30471
English
7
Connections
Y
VIDEO OUT
S-VIDEO OUT
COAXIAL
MAINS
DIGITAL OUT
L
R
AUDIO OUT
Pb
Pr
COMPONENT
VIDEO OUT
AUDIO
IN
V(Pr/Cr)
U(Pb/Cb)
Y
S-VIDEO
IN
VIDEOIN
COMPONENT
VIDEOIN
AUDIO
IN
V (Pr/Cr)
U (Pb/Cb)
Y
S-VIDEO
IN
VIDEO IN
COMPONENT
VIDEO IN
2
1
IMPORTANT!
–S-Video connection provides
better picture quality.This option
must be available on yourTV.
Using S-Video jack
1Use the S-video cable to connect the
DVD system’s S-VIDEO OUT jack to
the S-Video input jack (or labeled asY/C
or S-VHS) on theTV (cable not supplied).
2To hear the sound of this DVD Player
through yourTV,use the audio cables
(white/red) to connectAUDIO OUT (L/
R) jacks of the DVD Player to the
correspondingAUDIO IN jacks on theTV
(cable supplied).
IMPORTANT!
–If yourTV only has a single
Antenna In jack (or labeled as 75
ohm or RF In,) you will need an RF
modulator in order to view the DVD
playback on theTV. See your
electronics retailer or contact
Philips for details on RF modulator
availability and operations.
Using an accessory RF modulator
1Use the composite video cable (yellow) to
connect the DVD Player’s CVBS (VIDEO
OUT) jack to the video input jack on the
RF modulator.
2Use the RF coaxial cable (not supplied) to
connect the RF modulator to yourTV’s
RF jack.
Y
VIDEO OUT
S-VIDEO OUT
COAXIAL
DIGITAL OUT
L
R
AUDIO OUT
Pb
Pr
COMPONENT
VIDEO OUT
AUDIO IN
R L
VIDEO
IN
TO TVANT IN
CH3 CH4
2
1
RF coaxial cable toTV
Back of RF Modulator
(example only)
Antenna or
CableTV signal
01-34 DVP532_4K_69 19/03/2004, 2:59 PM7

8239 300 30471
English
8
Connections
Y
VIDEO OUT
S-VIDEO OUT
COAXIAL
MAINS
DIGITAL OUT AUDIO O
Pb
Pr
COMPONENT
VIDEO OUT
~ AC MAINS
AUDIO
IN V(Pr/Cr)
U(Pb/Cb)
Y
S-VIDEO
IN
VIDEOIN
COMPONENT
VIDEOIN
After everything is connected
properly,plug in theAC power cord
to the power outlet.
Never make or change any connections
with the power switched on.
When no disc is loaded,press
STANDBY ON on the DVD Player
front panel,
“NO DISC” may appear on the
display panel.
EN/CLOSE STOP PLAY/PAUSE
Connecting the power cord
NO DISC
01-34 DVP532_4K_69 19/03/2004, 2:59 PM8

8239 300 30471
English
9
Stereo system has Dolby Pro Logic
or Right / LeftAudio In jack
1Select one of the video connections
(VIDEO IN, S-VIDEO IN or Component
Video (Y Pb Pr) jack depending on the
options available on yourTV.
2Use the audio cables (white/red) to
connect AUDIO OUT (L/R) jacks of
the DVD Player to the corresponding
AUDIO IN jacks on the stereo system
(cable supplied).
Connections
Y
VIDEO OUT
S-VIDEO OUT
COAXIAL
DIGITAL OUT
L
R
AUDIO OUT
Pb
Pr
COMPONENT
VIDEO OUT
AUDIO
IN
STEREO
DIGITAL
OPTICAL
Optional: Connecting to an
Audio System Optional:Connecting Digital AV
Receiver
Y
VIDEO OUT
S-VIDEO OUT
COAXIAL
MAINS
DIGITAL OUT
L
R
AUDIO OUT
Pb
Pr
COMPONENT
VIDEO OUT
AUDIO
IN
COAXIAL
AV Receiver
Receiver has a PCM,Dolby Digital,
or MPEG2 decoder
1Select one of the video connections
VIDEO IN, S-VIDEO IN or Component
Video (Y Pb Pr) jack depending on the
options available on yourTV.
2Connect the COAXIAL jack of the DVD
Player to the corresponding DigitalAudio
In jack on your Receiver (cable not
supplied).
3Set the DVD Player’s Digital Output to
PCM-ONLY orALL depending on the
capabilities of your Receiver (see page 24
“Digital Output”).
Helpful Hint:
–If the audio format of the Digital Output
does not match the capabilities of your
receiver,the receiver will produce a strong,
distorted sound or no sound at all.
01-34 DVP532_4K_69 19/03/2004, 2:59 PM9

8239 300 30471
English
10
Functional Overview
Front Panels
20:58:02
STANDBY-ON B
–To switch the DVD Player to Standby
mode or ON
Disc tray
OPEN/CLOSE /
–Open/Close the disc tray
2; PLAY/PAUSE
–To start or interrupt playback
9 STOP
–To stop playback
IR Sensor
– Point the remote control towards this
sensor
Display
– Shows the current status of the DVD
Player
MIC
– For connecting microphone
LEVEL
– Microphone volume control
20:58:02
ON PLAY
STANDBY-ON B
–To switch the DVD Player to Standby
mode or ON
Disc tray
OPEN/CLOSE /
–Open/Close the disc tray
2; PLAY/PAUSE
–To start or interrupt playback
9 STOP
–To stop playback
IR Sensor
– Point the remote control towards this
sensor
PLAY light
– Blue light appears during disc playback
ON light
– Blue light appears when DVD player is on
MIC
– For connecting microphone
LEVEL
– Microphone volume control
DVP532K
DVP534K
01-34 DVP532_4K_69 19/03/2004, 2:59 PM10

8239 300 30471
English
11
Audio Out (Left/Right)
– Connect toAUDIO inputs of an amplifier,
receiver or stereo system
Digital Out (Coaxial)
– Connect to coaxialAUDIO input of a
digital audio equipment
ComponentVideo Out (Y Pb Pr)
– Connect to aTV with Y Pb Pr inputs
Y
VIDEO OUT
S-VIDEO OUT
COAXIAL
MAINS
DIGITAL OUT
L
R
AUDIO OUT
Pb
Pr
COMPONENT
VIDEO OUT
Mains (AC Power Cord)
–Connect to a standardAC outlet
S-Video Out
–Connect to S-Video input of aTV
Video Out (CVBS)
–Connect to CVBSVideo input of aTV
Caution:Do not touch the inner pins of the jacks on the rear panel.
Electrostatic discharge may cause permanent damage to the unit.
Functional Overview
Rear Panel
01-34 DVP532_4K_69 19/03/2004, 2:59 PM11

8239 300 30471
English
12
Functional Overview
Remote Control
PREVIEW MUTE
MUTE
VOCAL MODE
MODE
KARAOKE KEY
RETURN /TITLE
–To go back to previous menu /
show title menu
DISC MENU
– Enters or exits the disc contents
menu
– Switches on or off the playback
control mode (forVCD version
2.0 only)
1 2 3 4
– Selects an item in the menu/
fast forward/backward,slow forward/
backward
OK
–Acknowledge menu selection
S
–To search or select previous
chapter or track
STOP ( 9)
–To stop playback
PLAY ( B)
–To start playback
PAUSE ( ;)
–To pause playback temporarily /
frame-by-frame playback
REPEAT
– Selects various repeat modes
REPEAT (A-B)
– Repeats playback a specific section
on a disc
PREVIEW
–To preview the content of a track
or whole disc
MUTE
– Disables or enables sound output
POWER B
–To switch the DVD player to
standby mode or ON
0-9 numerical key pad
–Selects numbered items in a
menu
DISPLAY
–Displays information onTV
screen during playback
SYSTEM MENU
–Access or exit DVD Player’s
system menu
T
–To search or select next chapter
or track
SUBTITLE
–To access subtitle language
system menu
ANGLE
–Selects a DVD camera angle
ZOOM
–Enlarge or reduce a picture on
theTV screen
AUDIO
–To access audio language system
menu
KARAOKE
–Display karaoke menu to set MIC
on or off
KEY
–Display karaoke menu to set key
control
VOCAL
–Choose audio channels or
karaoke methods
MODE
–Display karaoke menu
01-34 DVP532_4K_69 19/03/2004, 2:59 PM12

8239 300 30471
English
13
STOP
PREVIEWPREVIEW MUTEMUTE
Getting Started
Step 1: Inserting batteries into
the Remote Control
1
3
2
1Open the battery compartment.
2Insert two batteries type R06 orAA,
following the indications (+-) inside
the compartment.
3Close the cover.
Using the Remote Control to
operate the Player
1Aim the Remote Control
directly at the remote
sensor (IR) on the front
panel.
2Do not put any objects
between the Remote
Control and the DVD
Player while operating the
DVD Player.
CAUTION!
–Remove batteries if they are
exhausted or if the Remote Control
is not being used for a long time.
–Do not use old and new or
different types of batteries in
combination.
–Batteries contain chemical
substances,so they should be
disposed properly.
Step 2: Setting up theTV
IMPORTANT!
Make sure you have completed all
the necessary connections.(See
pages 6-7“ConnectingTV”).
1Turn on theTV and set to the correct
video-in channel. You should see the blue
Philips DVD background screen on the
TV.
➜Usually these channels are between the
lowest and highest channels and may be
called FRONT,A/V IN,orVIDEO.See your
TV manual for more details.
➜Or,you may go to channel 1 on your
TV,then press the Channel down button
repeatedly until you see theVideo In
channel.
➜Or,theTV Remote Control may have a
button or switch that chooses different
video modes.
➜Or,set theTV to channel 3 or 4 if you
are using an RF modulator.
2If you are using external equipment,(eg.
audio system or receiver),turn it on and
select the appropriate input source for
the DVD Player output.Refer to the
equipment owner’s manual for detail.
01-34 DVP532_4K_69 19/03/2004, 2:59 PM13

8239 300 30471
English
14
Getting Started
1Press SYSTEM MENU.
2Press 12to select‘Video Setup Page’.
3Use the 1234keys on the Remote
Control to navigate in the menu.
Move to‘TVType’ and press 2.
PAL – Select this if the connectedTV is
PAL system.It will change the video signal
of a NTSC disc and output in PAL format.
NTSC – Select this if the connectedTV
is NTSC system. It will change the video
signal of a PAL disc and output in NTSC
format.
Multi – Select this if the connectedTV is
compatible with both NTSC and PAL
(multi-system). The output format will be
in accordance with the video signal of the
disc.
4Select an item and press OK.
Selecting the colour system that
corresponds to yourTV
This DVD Player is compatible with both
NTSC and PAL.In order for a DVD disc
to play on this Player,the colour system of
the Disc,theTV and the DVD Player
should match.
- - Video Setup Page - -
Set TV Standard
TV Type PAL
TV Display NTSC
Closed Captions Multi
Angle Mark
Progressive
Smart Picture
Picture Setting
Helpful Hint:
–Before changing the currentTV
Type setting,ensure that yourTV
supports the‘selectedTVType’system.
–Follow the instructions that
appears on theTV screen.
–If there is no proper picture on
yourTV,wait for 15 seconds for auto
recovery.
HINTS:(refer to the owner's manual
Changing to (selected TV Type)
1. Ensure your TV supports it.
2. If there is a blank screen on normal TV,
wait 15 seconds for auto recover
< > - Move OK - Select
Cancel
OK
Confirm again to use (selected TV Type)
If picture is good press OK on remote
TO GO BACK TO (Current TV Type):
1. Open tray
2. Press '3' Key
< > - Move OK - Select
Cancel
OK
To exit from the menu
Press SYSTEM MENU or select‘Exit
Setup Menu’ and then press OK.
01-34 DVP532_4K_69 19/03/2004, 2:59 PM14

8239 300 30471
English
15
Step 3: Setting language
preference
You can select your own preferred
language settings.This DVD system will
automatically switch to the selected
language whenever you load a disc. If the
language selected is not available on the
disc,the disc’s default language will be
used instead. The OSD language in the
system menu will remain once selected.
Setting the OSD Language
1Press SYSTEM MENU.
2Press 12to select‘General Setup’ page.
3Use the 1234keys on the Remote
Control to navigate in the menu.
Move to‘OSD Language’ and press 2.
4Select a language and press OK.
To exit from the menu
Press SYSTEM MENU or select‘Exit
Setup Menu’ and then press OK.
Setting theAudio,Subtitle and Disc
menu language
- - Preference Page - -
Set Preference To English
Audio English
Subtitle Chinese
Disc Menu Japanese
Parental French
Password German
Default Spanish
Dutch
Italian
1Press STOP twice then,press SYSTEM
MENU.
2Press 12to select‘Preference Page’.
3Press 34to highlight the following in the
Preference Page.
–‘Audio’ (disc’s soundtrack)
–‘Subtitle’ (disc’s subtitles)
–‘Disc Menu’ (disc’s menu)
4Enter its submenu by pressing B.
5Select a language and press OK.
6Repeat steps 3~5for other language
settings.
To exit from the menu
Press SYSTEM MENU or select‘Exit
Setup Menu’ and then press OK.
If you choose OTHERS inAudio,
Subtitle or Disc Menu,
1Press 34to highlight‘Others’.
2Press OK and when you are asked to
enter a language code (see‘Language
Code’ on page 130).
3Input a language code by using the
numeric keypad (0-9).
4Press OK to confirm.
Getting Started
01-34 DVP532_4K_69 19/03/2004, 2:59 PM15

8239 300 30471
English
16
Disc Operations
IMPORTANT!
–Depending on the DVD orVIDEO
CD,some operations may be
different or restricted.
–Do not push on the disc tray or
put any objects other than disc on
the disc tray. Doing so may cause
the disc player malfunction.
Playable Discs
Your DVD Player will play:
●Discs:
–DigitalVersatile Discs (DVDs)
–Video CDs (VCDs)
–SuperVideo CDs (SVCDs)
–DigitalVersatile Discs + Recordable
(DVD+R)
–DigitalVersatile Discs + Rewritable
(DVD+RW)
–Compact Discs (CDs)
–MP3 disc on CD-R(W):
–Maximum 30 characters display.
–Supported sampling frequencies :
32 kHz, 44.1 kHz, 48 kHz
–Supported Bit-rates :32~256 kbps
variable bitrates
–Picture (JPEG) files on CD-R(W):
–JPEG/ISO 9660 format.
Region Codes
DVDs must be labelled for ALL
regions or Region 3 in order to
play on this DVD system. You
cannot play discs that are labelled
for other regions.
Helpful Hint:
–If you are having trouble playing a
certain disc,remove the disc and try a
different one. Improper formatted disc will
not play on this DVD Player.
ALL
IMPORTANT!
If the inhibit icon (ø) appears on the
TV screen when a button is pressed,
it means the function is not available
on the current disc or at the current
time.
Playing discs
1Connect the power cords of the DVD
Player andTV (and any optional stereo or
AV receiver) to a power outlet.
2Turn on theTV power and set to the
correctVideo In channel. (See page 13
“Setting up theTV”).
3Press STANDBY-ON on the DVD Player
front panel.
➜You should see the blue Philips DVD
background screen on theTV.
4Press OPEN•CLOSE 0button to open
the disc tray and load in a disc,then press
the same button again to close the disc
tray.
➜Make sure the label side is facing up.
For double-sided discs,load the side you
want to play facing up.
5Playback will start automatically
(depending on the disc type).
➜If a disc menu appears on theTV,see
“Using the Disc Menu”.
➜If the disc is locked by parental control,
you must enter your four-digit password.
(See page 30).
6At any time,simply press STOP to stop
playback.
3
01-34 DVP532_4K_69 19/03/2004, 2:59 PM16

8239 300 30471
English
17
Disc Operations
Using the Disc Menu
Depending on the disc,a menu may
appear on theTV screen once you load
the disc.
To select a playback feature or item
●Use the 1234or numeric keypad
(0-9) on the Remote Control,then press
PLAY Bto start playback.
To access or exit from the menu
●Press DISC MENU on the Remote
Control.
ForVCD with Playback Control
(PBC) feature (version 2.0 only)
PBC playback allows you to playVideo
CDs interactively,following the menu on
the display.
●In stop mode,use the numeric keypad
(0-9) to select a track and PBC will turn
off.
➜Playback will start automatically
●During playback,press DISC MENU;
➜If PBC was ON,it will switch to OFF
and continue playback.
➜If PBC was OFF,it will switch to ON
and return to menu screen.
●During playback,pressing RETURN/
TITLE will return to the menu screen (if
PBC is on).
Basic playback controls
Unless otherwise stated, all operations
described are based on the use of
Remote Control.
Pausing playback
(DVD/SVCD/VCD/CD/MP3)
1During playback,press PAUSE ;.
➜Playback will pause and sound will be
muted.
2Press PAUSE ;again to select the next
picture frame.
3To return to normal playback,press
PLAY B.
Selecting track/chapter
(DVD/SVCD/VCD/CD)
1Press Tbriefly during playback to go
to the next chapter/track
2Press Sto go to the previous track
(VCD/CD) or return to the beginning of
the current chapter (DVD/SVCD).
●Press Stwice briefly to step back to
the previous chapter (DVD/SVCD).
3To go directly to any chapter/track,enter
the chapter/track number using the
numerical keys (0-9).
Resuming playback from the last
stopped point
(DVD/SVCD/VCD/CD/MP3)
●In stop mode and when the disc has not
been ejected,press PLAY B.
To cancel resume mode
●In stop mode,press STOP 9again.
01-34 DVP532_4K_69 19/03/2004, 2:59 PM17

8239 300 30471
English
18
Disc Operations
Repeat (DVD/SVCD/VCD/CD)
●Press REPEAT continuously to choose a
Repeat mode during playback.
REPEAT CHAPTER (DVD)
–to repeat playback of the current
chapter.
REPEATTRACK/TITLE (CD/SVCD/VCD/
DVD)
–to repeat playback of the current
track (CD/SVCD/VCD)/title (DVD).
REPEATALL
–to repeat playback of all the disc and
all the programmed tracks.
SHUFFLE
–to repeat playback at random order.
REPEAT OFF
–to cancel the repeat mode.
Helpful Hint:
–REPEAT function is not available for
SVCD/VCD 2.0 when PCB is on.
RepeatA-B (DVD/SVCD/VCD/CD)
1Press REPEATA-B at your chosen
starting point.
2Press REPEATA-B again at your chosen
end point.
➜The sectionA and B can be set only
within the same chapter/track.
➜The section will now repeat continuously.
3To exit the sequence,press REPEATA-B.
Forward / Reverse Searching
(DVD/SVCD/VCD)
1Press 12during playback to select the
required speed:2X,4X,8X,16X or 32X
(backward or forward).
➜Sound will be muted (DVD/SVCD/
VCD) or intermittent (CD).
2To return to normal speed,press PLAY B.
Slow Motion (DVD/SVCD/VCD)
1Press 34during playback to select the
required speed:1/2,1/4,1/8 or 1/16
(backward or forward).
➜Sound will be muted.
2To return to normal speed,press PLAY B.
Helpful Hint:
–Slow backward is not possible on SVCDs/
VCDs.
Zoom (DVD/SVCD/VCD/JPEG)
Zooming allows you to enlarge or reduce
the video image during playback.
1Press ZOOM repeatedly to increase and
decrease the playback video image.
2Press 1234to pan across theTV
screen.
01-34 DVP532_4K_69 19/03/2004, 2:59 PM18

8239 300 30471
English
19
Disc Operations
Special disc features
Playing aTitle (DVD)
1Press DISC MENU.
➜The disc title menu appears on theTV
screen.
2Use 341 2 keys or numeric keypad
(0-9) to select a play option.
3Press OK key to confirm.
CameraAngle (DVD)
●Press ANGLE repeatedly to select
different desired angle.
Changing theAudio Language
(DVD/VCD)
For DVD
●Press AUDIO repeatedly to select
different audio languages.
Changing theAudio Channel
ForVCD
●Press AUDIO to select the available
audio channels provided by the disc
(STEREO,MONO LEFT,MONO RIGHT
or MIX MONO).
Subtitles (DVD)
●Press SUBTITLE repeatedly to select
different subtitle languages.
Time Search (DVD/SVCD/VCD)
TheTime Search function allows you to
start playing at any chosen time on the
disc.
1Press DISPLAY.
2Press 3 4 to highlight time search box.
➜The on-screen display shows the total
playing time of the title/chapter.
Bitrate 67 TT Elapsed 0:16:35
Bitrate 67 TT Elapsed 0:16:35
TT Time
TT Time
0:03:01
0:03:01
CH Time
CH Time
0:01:08
0:01:08
Repeat
Repeat
Off
Off
Time Disp.
Time Disp.
TT Elapsed
TT Elapsed
Menu
Menu
3Use 2keys to select an option.
4Enter hours,minutes and seconds from
left to right in the time edit box using
remote control numerical key pad.
(e.g.0:34:27)
For DVD
➜Title/Chapter Remain:displays the
remaining time of the current title/
chapter.
➜Title/Chapter Elapsed:displays the
elapsed time of the current title/chapter.
For SuperVCD orVCD
➜Total/Single Remain:displays the
remaining time of the current total/single
track.
➜Total/Single Elapsed:displays the
elapsed time of the current total/single
track.
5Press the DISPLAY key to confirm.
➜Playback starts from the selected time
on the disc.
01-34 DVP532_4K_69 19/03/2004, 2:59 PM19

8239 300 30471
English
20
Disc Operations
Playing MP3/JPEG Picture CD
IMPORTANT!
You have to turn on yourTV and set to
the correctVideo In channel. (See page
13“Setting up theTV”).
General Operation
1Load an MP3/JPEG Picture CD disc.
➜The data disc menu appears on theTV
screen.
2Use 34to select the folder and press
OK to open the folder.
00:37 03:50 128kbps
001/162
\MP3\
Song 1
Song 2
Song 3
Song 4
Song 5
MP3
MP3
MP3
MP3
MP3
3Press 34or use the numeric keypad
(0-9) to highlight an option.
4Press OK to confirm.
➜The playback will start from the
selected file to the end of the folder.
Preview Function (DVD/VCD/CD)
The preview function allows you to
reduce the picture of 6 tracks enough to
display in a full screen.
1Press PREVIEW.
➜The preview menu appears on theTV
screen.
Select Digest Type:
Title Digest
Chapter Digest
Title Interval
Chapter Interval
Select Digest Type:
Title Digest
Chapter Digest
Title Interval
Chapter Interval
Select Digest Type:
Track Digest
Disc Interval
Track Interval
Select Digest Type:
Track Digest
Disc Interval
Track Interval
2Press 34to select the PREVIEW type,
then press OK.
➜The picture of each segment will
appear on the screen.
ABC
DEF
(example for 6 thumbnail pictures display)
3Press 3412to select a track and input
your selected track number using the
numeric keypad (0-9),then press OK.
➜Playback will start automatically on the
selected track.
●For CDDA (Musical CD)
➜Press PREVIEW to listen to the first
10 seconds of each sound track in the
disc.
(DVD example) (Video CD example)
01-34 DVP532_4K_69 19/03/2004, 2:59 PM20