Philips DVD761/002 User manual

1
DVD Video player
DVD761

2
Important Note
DK
Advarsel:
Laserrudstråling ved åbning når sikkerhesafbrydere er ude af
funktion. Undgå u tsættelse for stråling.
Bemærk:
Netafbryderen POWER er sekundært indkoblet og afbryder ikke
strømmen fra nette. Den indbyggede netdel er derfor tilsluttet til
lysnettet så længe netstikket sidder i stikkontakten.
S
Klass 1 laserapparat
Varning!
Om apparaten används på annat sätt än i denna bruksanvisning
specificerats, kann användaren utsättas för laserstrålning, som
översjruder gränsen för läserklass 1.
Observera!
Strömbrytaren POWER är sekundärt kopplad och inte bryter
strömmen fråan nätet Den inbyggda nätdelen är därför ansluten till
elnätet så länge stickproppen sitter i v ägguttaget.
N
Observer:
Nettbryteren POWER er sekundert innkoplet. Den
innebygdenetdelen er derfor ikke frakoplet nettet så lenge apparatet
er tilsluttet nettkontakten.
SF
Luokan 1 laserlaite + Klass 1 laserapparat
Varoitus!
Laitteen käyttäminen muulla kuin tässä käyttöohjeessa mainitulla
tavalla saattaa altistaa käyttäjän turvallisuusluokan 1 ylittävälle
lasersäleilille.
Huom.
Toiminnanvalitsin POWER on kytketty toisiopuolelle, eikä se kytke
laitetta irti sähköverkosta. Sisäänrakennettu verkko-osa on
kytkettynä sähköverkkoon aina silloin, kun pistoke on pistorasiassa.
This product incorporates copyright protection
technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned
by Macrovision Corporation and other rights owners. Use
of this copyright protection technology must be
authorized by Macrovision Corporation, and is intended
for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of
Dolby Laboratories. Confidential Unplublished Works.
© 1992 - 1997 Dolby Laboratories, Inc. All rights
reserved.
Important Note for Users in the UK
Mains plug
This apparatus is fitted with an approved 13 Amp plug.To
change a fuse in this type of plug proceed as follows:
1 Remove fuse cover and fuse.
2 Fix new fuse which should be a BS1362 5 Amp,
A.S.T.A. or BSI approved type.
3 Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place.
If the mains plug contains a fuse, this should have a value of 5
Amp. If a plug without a fuse is used, the fuse at the
distribution board should not be greater than 5 Amp.
Note:The severed plug must be disposed of to avoid a possible
shock hazard should it be inserted into a 13 Amp socket
elsewhere.
How to connect a plug
The wires in the mains lead are coloured with the following
code: blue = neutral (N), brown = live (L).
As these colours may not correspond with the colour
markings identifying the terminals in your plug, proceed as
follows:
• Connect the blue wire to the terminal marked N or
coloured black.
• Connect the brown wire to the terminal marked L
or coloured red.
• Do not connect either wire to the earth terminal in
the plug, marked E (or e) or coloured green
(or green and yellow).
Before replacing the plug cover, make certain that the cord grip
is clamped over the sheath of the lead - not simply over the
two wires.
Copyright in the U.K.
Recording and playback of material may require
consent. See Copyright Act 1956 and The Performer’s
Protection Acts 1958 to 1972.
IMPORTANT NOTE

3
English
Español
Deutsch
Nederlands
Italiano
Svenska
Dansk
Suomi
Português
∂ÏÏËÓÈο Français
Index
INDEX
English -------------------------------------------------------- 9
Français ------------------------------------------------------ 31
Español ------------------------------------------------------ 54
Deutsch ----------------------------------------------------- 77
Nederlands ----------------------------------------------- 100
Italiano ----------------------------------------------------- 122
Svenska ---------------------------------------------------- 144
Dansk ------------------------------------------------------ 166
Suomi ------------------------------------------------------ 188
Português ------------------------------------------------- 210
∂ÏÏËÓÈο -------------------------------------------------- 232

4
General Information
GENERAL INFORMATION
NOTE:
PICTURES SHOWN MAYBE DIFFERENT
BETWEEN COUNTRIES.
CAUTION
(WARNING LOCATION: INSIDE ON LASER
COVERSHIELD OR THE BACKPLATE OF SET)
NEVER MAKE OR CHANGE CONNECTIONS
WITH THE POWER SWITCHED ON.
The region code for this set is 2.
Since it is usual for DVD movies to be released at
different times in different regions of the world,
all players have region codes and discs can have an optional
region code. If you load a disc of a different region code to
your player, you will see the region code notice on the
screen.The disc will not play, and should be unloaded.
2Laser safety
This unit employs a laser. Due to possible eye injury, only a
qualified service person should remove the cover or
attempt to service this device.
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION
EXPOSURE.
For Customer Use:
Read carefully the information located at the bottom of
your DVD-VIDEO player and enter below the Serial
No.Retain this information for future reference.
Model No. DVD-VIDEO
Serial No. __________________________
TruSurround and the SRS symbol are trademarks of SRS
Labs., Inc.TruSurround technology is manufactured under
license from SRS Labs., Inc.
LASER
Type Semiconductor laser GaAlAs
Wave lenght 650 nm (DVD)
780 nm (VCD/CD)
Output Power 7 mW (DVD)
10 mW (VCD/CD)
Beam divergence 60 degree
CAUTION
VISIBLE AND INVISIBLE LASER RADIATION WHEN
OPEN AVOID EXPOSURETO BEAM
ADVARSEL
SYNLIG OG USYNLIG LASERSTRÅLINGVED ÅBNING
UNDGÅUDSÆTTELSE FOR STRÅLING
ADVARSEL
SYNLIG OG USYNLIG LASERSTRÅLING NÅR DEKSEL
ÅPNES UNNGÅEKSPONERING FOR STRÅLEN
VARNING
SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR
DENNA DEL ÄR ÖPPNAD BETRAKTA EJ STRÅLEN
VARO!
AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA
NÄKYMÄTTÖMÄLLE LASER SÄTEILYLLE. ÄLÄKATSO
SÄTEESEEN
VORSICHT
SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG
WENN ABDECKUNG GEÖFFNET NICHT DEM
STRAHL AUSSETSEN
DANGER
VISIBLE AND INVISIBLE LASER RADIATION WHEN
OPEN AVOID DIRECT EXPOSURE TO BEAM
ATTENTION
RAYONNEMENT LASER VISIBLE ET INVISIBLE EN CAS
D’OUVERTURE EXPOSITION DANGEREUSE AU
FAISCEAU
The DVD-VIDEO player is in conformity
with the EMC directive and low-voltage
directive.

5
Universal Remote Control Setup Codes
Activating the Remote Control Setup Code for Compatible TVs
¶Press and hold both RETURN and OK buttons on the remote control for 3 seconds and release.
¶Immediately key-in the selected code from the list below (The list may not be applicable for each and every TV brand listed.)
Activation du code d’installation de la télécommande pour les téléviseurs compatibles
¶Appuyez sur les touches RETURN et OK sur la télécommande et maintenez-les enfoncées pendant 3 secondes et relâchez-les
ensuite.
¶Tapez immédiatement le code repris dans la liste ci-dessous (il se peut toutefois que cette liste ne s’applique pas àtoutes les
marques de téléviseurs mentionnées).
Activación del código de configuración del mando a distancia para televisores compatibles
¶Mantenga pulsados al mismo tiempo los botones RETURN y OK del mando a distancia durante tres segundos, y libérelos.
¶Inmediatamente teclee el código correspondiente de la siguiente lista (la lista puede que no sea aplicable a todas y cada una de
las marcas incluidas en la misma).
Aktivieren des Fernbedienungs-Setup-Codes für kompatible Fernsehgeräte
¶DieTasten RETURN und OK auf der Fernbedienung gleichzeitig 3 Sekunden gedrückt halten und wieder loslassen.
¶Unmittelbar danach den gewünschten Code aus der unten stehenden Liste eingeben (Die Liste kann u.U. nicht auf jede
Fernsehgerätemarke zutreffen).
Instellen van de afstandsbediening voor uw tv
¶Houd de toetsen RETURN en OK op de afstandsbediening gedurende 3 seconden gelijktijdig ingedrukt en laat ze daarna los.
¶Toets direct de uit onderstaande lijst geselecteerde code in (de lijst bevat wellicht niet alle tv-merken).
Attivazione del codice di impostazione del telecomando per i televisori compatibili
¶Tenere premuti per 3 secondi i tasti RETURN (INVIO) e OK e quindi rilasciarli.
¶Subito dopo inserire tramite i tasti il codice selezionato dall’elenco seguente (èpossibile che l’elenco non sia applicabile per tutte
le singole marche di televisori indicate).
Aktivering av Fjärrkontrollens installationskod för kompatibla TV-apparater
¶Tryck ner och håll kvar både RETURN- och OK-knappen påfjärrkontrollen i 3 sekunder och släpp.
¶Knappa omedelbart in den valda koden från nedanstående lista (Listan gäller eventuellt inte varje upptaget TV-märke.)
Aktivering af opsætningskoden til fjernbetjeninger for kompatible fjernsyn
¶Tryk påog hold både knappen RETURN og knappen OK påfjernbetjeningen nede i 3 sekunder og slip derefter knapperne.
¶Indtast direkte den valgte kode fra nedenstående liste. (Det er muligt, at listen ikke gælder for hver eneste fjernsynsmærke, der er
anført pålisten.)
Yhteensopivien televisioiden asetuskoodin aktivointi kauko-ohjaimeen
¶Paina kauko-ohjaimen RETURN- ja OK-painikkeita yhtäaikaa ja pidäne painettuina 3 sekunnin ajan.Vapauta painikkeet.
¶Näppäile välittömästi alla olevasta luettelosta valittu koodi. (Luettelo ei mahdollisesti sovellu kaikille mainituilleTV-merkeille.)
Activar o Código de Configuração do Controlo Remoto para Televisores Compatíveis
¶Prima e deixe as teclas RETURN e OK do controlo remoto premidas, durante 3 segundos, e, depois, liberte.
¶Introduza imediatamente o código seleccionado da seguinte lista (épossível que a lista não abranja a totalidade das marcas de
televisores enumeradas)
∂vÂÚÁÔÔ›ËÛË ÙÔ˘ ∫ˆ‰ÈÎÔ‡ ƒ‡ıÌÈÛ˘ ÙÔ˘ ∆ËϯÂÈÚÈÛÙËÚ›Ô˘ ÁÈ· ™˘Ì‚·Ù¤˜ ∆ËÏÂÔÚ¿ÛÂȘ
¶¶·Ù‹ÛÙÂ Î·È ÎÚ·Ù‹ÛÙ ·ÙË̤ӷ Ù· ÎÔ˘ÌÈ¿ RETURN Î·È OK ÙÔ˘ ÙËϯÂÈÚÈÛÙËÚ›Ô˘ ÁÈ· 3 ‰Â˘ÙÂÚ ÏÂÙ· ηÈ
ÌÂÙ¿ ·Ê‹ÛÙÂ Ù·.
¶∞̤ۈ˜ ÏÎÙÚÔÏÔÁ‹ÛÙ ÙÔÓ ÂÈÏÂÁ̤ÓÔ Îˆ‰ÈÎ · ÙÔÓ ·Î ÏÔ˘ıÔ Î·Ù¿ÏÔÁÔ (Ô Î·Ù¿ÏÔÁÔ˜ ÌÔÚ› Ó· ÌËÓ
ÈÛ¯‡ÂÈ ÁÈ· οı ̿Úη ÙËÏ ڷÛ˘ Ô˘ ·Ó·ÁÚ¿ÊÂÙ·È).
UNIVERSAL REMOTE CONTROL SETUP CODES

6
AOC 046, 057
Acura 036
Admiral 120, 190
Adyson 244
Aiko 119
Akai 036, 057, 235, 245
Akura 245, 291
Alaron 206, 243
Alba 036, 063, 064, 245, 398
Allorgan 321
Amplivision 244
Amstrad 036, 064, 198, 398, 439
Anam 036, 095, 188, 207, 277
Anam National 188, 277
Anitech 036, 095
Arcam 243, 244
Asuka 245
Atlantic 233
Audinac 418
Audiosonic 064, 136
Audiovox 119, 207, 478
Autovox 233, 363
Awa 184
BPL 309
BSR 321
BTC 245
Baird 370
Bang & Olufsen 592, 647
Basic Line 036, 245
Baur 037, 064, 581
Baysonic 207
Beko 397
Belcor 046
Bell & Howell 043, 181
Beon 064
Binatone 244
Blaupunkt 218, 222, 227, 354, 355, 581
Blue Sky 245
Blue Star 309
Bondstec 274
Boots 244
Bradford 207
Brandt 136, 223, 225, 360, 362
Britannia 243
Brockwood 046
Broksonic 263, 490
Bush 036, 063, 064, 245, 309, 321, 398, 401
CCE 064, 244
CGE 274, 333
CS Electronics 243
CTC 274
CXC 207
Candle 057, 083, 213
Carnivale 057
Carrefour 063
Carver 081, 197
Cascade 036
Cathay 064
Celebrity 027
Centurion 064
Cimline 036
Cineral 119, 478
Citizen 057, 066, 083, 087, 119, 213
Clarivox 064
Clatronic 274, 397
Concerto 083
Condor 347, 397
Contec 036, 063, 184, 207, 243
Continental Edison 223, 225, 360
Craig 188, 207
Crosley 081
Crown 036, 064, 066, 207, 397, 445
Crystal 458
Curtis Mathes 043, 057, 066, 074, 078, 081, 083, 087,
120, 172, 181, 193, 478
Cybertron 245
Daewoo 036, 046, 064, 066, 119, 181, 401, 418,
478
Dainichi 242, 245
Dansai 064
Dayton 036
Daytron 046
De Graaf 235
Decca 064, 099
Denon 172
Dixi 036, 064
Dual 363
Dual Tec 244
Dumont 044, 046, 097
ECE 064
Ectec 418
Elbe 286
Electroband 027
Electrohome 436
Elin 064
Elite 245, 347
Elta 036
Emerson 046, 066, 181, 205, 206, 207, 263, 309,
490
Envision 057
Erres 039, 064
Etron 036
Expert 233
Ferguson 064, 136, 265, 314, 362, 370
Fidelity 243
Finlandia 235
Finlux 064, 097, 099, 132, 206
Firstline 321, 036, 243, 244, 274, 348
Fisher 181, 235, 244, 330, 397
Flint 482
Formenti 064, 347
Fortress 120
Frontech 190, 274, 291, 458
Fujitsu 206, 099, 233
Funai 198, 206, 207, 291, 321, 330
Futuretech 207
GE 048, 074, 078, 120, 205, 309, 478
GEC 064, 099, 244
GPM 245
Geloso 036
General 213
Genexxa 190, 245
Gibralter 044, 046, 057
GoldStar 046, 057, 064, 066, 083, 136, 205, 244,
317, 436
Goodmans 063, 064, 099, 206, 244, 344, 370, 398,
401
Gorenje 397
Gradiente 080, 083, 197
Graetz 190
Granada 064, 099, 235, 244, 366
Grandin 309
UNIVERSAL REMOTE CONTROL SETUP CODES

7
Grundig 064, 097, 218, 222, 581
Grunpy 206, 207
HCM 036, 309, 439
Hallmark 205
Hanseatic 064, 347, 583
Harley Davidson 206
Harman/Kardon 081
Harvard 095, 207
Hinari 036, 063, 064, 206, 245
Hisawa 309, 482
Hitachi 225, 063, 071, 083, 132, 136, 172,190,
223,244, 252, 333, 436
Huanyu 243, 401
Hypson 064, 291, 309
ICE 244, 291, 398
ICeS 245
ITS 398
ITT 190
Imperial 274, 397, 445
Indiana 064
Infinity 081
Ingelen 190
Inno Hit 099
Inteq 044
Interbuy 095
Interfunk 064, 190, 274
Intervision 064, 095, 129, 244, 291
Isukai 245
JBL 081
JCB 027
JVC 063, 080, 096, 121, 187, 398
KEC 207
KTV 057, 066, 207, 244
Kaisui 036, 243, 244, 245, 309
Kamp 243
Kapsch 190, 233
Kathrein 583
Kawasho 243
Kendo 064
Kenwood 046, 057
Kingsley 243
Kneissel 286
Korpel 064
Koyoda 036
LG 083
LXI 074, 081, 181, 183, 205
Leyco 064, 099, 291, 321
Liesenk & Tter 064
Logik 043
Luma 233
Luxman 083
M Electronic 036, 064, 095, 132, 136, 190, 244, 314,
401
MGA 046, 057, 177, 205
MTC 046, 057, 083, 087, 243
Magnadyne 129, 274
Magnafon 129
Magnavox 057, 063, 081, 206, 213
Majestic 043
Manesth 244, 291, 347
Marantz 057, 064, 081, 583
Mark 064
Maruman 418
Matsui 036, 062, 063, 064, 099, 235, 244, 321,
398
Matsushita 277
Mediator 039, 064
Megatron 172, 205
Memorex 036, 043, 083, 177, 181, 205, 277
Memphis 364
Midland 044, 066, 074, 078
Minerva 097, 581
Minoka 439
Minutz 048
Mitsubishi 046, 063, 120, 135, 177, 205
Mivar 243, 317, 318, 319
Motorola 120
Multitech 036, 129, 207, 243, 244
NAD 183, 193, 205
NEC 046, 057, 063, 083, 197, 482
NEI 064, 364, 458
NTC 119
National 253
Neckermann 064, 218, 581, 583
Nesco 206
Nicamagic 243
Nikkai 062, 064, 099, 243, 245, 291, 364
Nikko 057, 119, 205, 344
Nisato 418
Nobliko 129
Nordmende 136, 223, 225, 314, 370
Oceanic 190, 242
Onwa 207
Optimus 181, 193, 277
Optonica 120, 192
Orion 321, 064, 206, 263, 347, 348, 490
Osaki 099, 244, 245, 291, 439
Oso 245
Osume 099, 184
Otake 344
Otto Versand 037, 063, 064, 218, 244, 347, 370, 581, 583
Palladium 397, 445
Panama 244, 291
Panasonic 078, 153, 188, 190, 253, 277
Pathe Cinema 243, 265, 347
Pathe Marconi 223, 225, 360
Pausa 036
Penney 046, 048, 057, 066, 074, 078, 083, 087,
183, 205
Perdio 347
Philco 046, 057, 081, 172, 274, 490
Philips 039, 064, 081, 401, 581, 583
Phonola 039, 064
Pilot 046, 057, 066
Pioneer 136, 190, 193, 314
Portland 046, 066, 119
Prism 078
Profex 036
Proline 348
Proscan 074
Protech 036, 064, 129, 244, 274, 291, 364, 445, 458
Proton 205
Pulsar 044, 046
Pye 039
Quasar 078, 192, 277
Quelle 037, 064, 097, 227, 333, 354, 355, 581
Questa 063
R-Line 064
RBM 097
RCA 046, 074, 078, 117, 120
Radio Shack 046, 057, 066, 074, 083, 181, 192, 205,
207, 436
UNIVERSAL REMOTE CONTROL SETUP CODES

8
Radiola 039, 064
Rank Arena 063
Realistic 046, 057, 066, 083, 181, 192, 205, 207
Revox 064
Rex 190, 233, 286, 291
Rhapsody 243
Roadstar 036, 245, 291, 445
Runco 044, 057
SBR 039, 064
SEG 063, 244, 291
SEI 129, 321
SSS 046, 207
Saba 136, 190, 223, 225, 314, 362, 370
Saccs 265
Saisho 036, 291, 458
Salora 190
Sambers 129
Sampo 057, 066
Samsung 036, 046, 057, 064, 066, 083, 087, 117,
205, 244, 291, 317, 397, 583
Samsux 066
Sandra 243
Sansei 478
Sansui 490
Sanyo 063, 099, 181, 184, 235, 366
Schneider 064, 245, 274, 330, 363, 398
Scimitsu 046
Scotch 205
Scott 046,205, 206, 207, 263
Sears 074, 081, 083, 181, 183, 198, 205, 206
Sei-Sinudyne 037
Seleco 190, 233, 286
Semivox 207
Semp 183
Sentra 062
Sharp 063, 066, 120, 184, 192
Shogun 046
Shorai 321
Siarem 129
Siemens 064, 184, 218, 222, 227, 354, 355, 581
Signature 043
Silver 063
Simpson 213
Sinudyne 129, 321
Sky-Worth 064
Solavox 190
Sonitron 235
Sonoko 036, 064
Sonolor 190, 235, 242
Sontec 064
Sony 027, 037, 063
Soundesign 205, 206, 207, 213
Soundwave 064, 445
Squareview 198
Standard 036, 244, 245
Starlite 207
Stern 190, 233, 286
Sunkai 321, 348
SuperTech 243
Supra 083
Supreme 027
Susumu 245
Sylvania 057, 081
Symphonic 198
Sysline 064
TMK 083, 205
Tandy 066, 099, 120, 190, 244, 245
Tashiko 063, 244
Tatung 064, 099, 244
Tec 244, 274
Technema 347
Technics 078, 277
Technol Ace 206
Techwood 078, 083
Teknika 043, 046, 066, 081, 083, 087, 119, 177,
206, 207,213
Teleavia 360, 0370
Telefunken 083, 136, 333, 362, 370
Telemeister 347
Teletech 036
Teleton 213, 233, 244
Tensai 245, 321, 344, 347
Texet 243, 245
Thomson 136, 223, 225, 314, 360, 370
Thorn 062, 064, 099, 370
Tomashi 309
Toshiba 062, 063, 087, 097, 181, 183, 270
Totevision 066
Trical 184
Triumph 270
Uher 233, 330, 347
Ultra 418
Ultravox 129
Universum 064, 132, 291, 397
Vector Research 057
Vestel 064
Victor 063, 080, 187, 277
Videosat 274
Videotechnic 244
Vidikron 081
Vidtech 046, 063, 205
Vision 347
Voxson 190
Waltham 244
Wards 043, 046, 048, 057, 081, 083, 192, 205,
206
Watson 064, 347
Watt Radio 129
Wega 063
White Westinghouse 064, 243, 347
Yamaha 046, 057
Yoko 064, 244, 291, 458
Zanussi 233
Zenith 043, 044, 119
UNIVERSAL REMOTE CONTROL SETUP CODES

9
English
Contents
Introduction
Philips DVD-Video Introduction ------------------------ 10
Unpacking --------------------------------------------------- 10
Safety Information ----------------------------------------- 10
Cleaning Discs --------------------------------------------- 10
Functional overview
Front panel ------------------------------------------------- 11
Rear panel -------------------------------------------------- 12
Display ------------------------------------------------------- 13
Remote control -------------------------------------------- 14
On-screen display information
Menu bar/Status window --------------------------------- 15
Status window icons --------------------------------------15
Default screen---------------------------------------------- 15
Temporary feedback field icons ------------------------- 15
Preparation
General notes ---------------------------------------------- 16
Connecting to a TV --------------------------------------- 16
Connecting to optional equipment-----------------16-17
Remote Control battery installation ------------------- 17
NTSC/PAL Settings ---------------------------------------- 17
General explanation -------------------------------------- 18
Turning on the power ------------------------------------ 18
Initial Setup ---------------------------------------------18-19
Personal Preferences----------------------------------19-20
Access Control: child lock ------------------------------- 21
Access Control: parental control -------------------21-22
Operation
Loading discs ----------------------------------------------- 23
Playing a DVD-Video disc --------------------------------23
Playing a Video CD ---------------------------------------- 23
General Features --------------------------------------23-25
Special DVD features ------------------------------------- 26
Special VCD features -------------------------------------- 26
Playing an Audio CD ----------------------------------26-27
FTS Program ----------------------------------------------- 27
Before requesting service
Before requesting service --------------------------------28
Appendix
Speaker Settings ----------------------------------------- 29
Specifications
Specifications ----------------------------------------------- 30
CONTENTS

10
English
Introduction
Philips DVD-Video
Introduction
Your Philips DVD-Video player will play digital video discs
conforming to the universal DVD-Video standard.With it,
you will be able to enjoy full-length movies with true
cinema picture quality, as well as stereo or multi-channel
sound (depending on the disc and your playback setup).
The unique features of DVD-Video, such as selection of
sound track, subtitle languages and different camera angles
(again depending on the disc), are all included.What’s more,
Philips Child Lock lets you decide which discs your children
will be able to see.
In addition to DVD-Video discs, you will be able to play all
Video CDs and Audio CDs (including finalized CD
Recordable and CD Rewritable).
You will find the On-Screen Display, player display, and
remote control make the player easy to use.This manual
provides all the information you will need, so read on!
DVD-Video
You will recognize DVD-Video discs by
the logo shown.
Depending on the material on the disc (a movie, video clips,
a drama series, etc.) the disc may have one or moreTitles.
TITLE 1 TITLE 2
CHAPTER 1 CHAPTER 2 CHAPTER 1 CHAPTER 2 CHAPTER 3
DVD-VIDEO DISC
Video CD
You will recognizeVideo CDs by the logo
shown.
Audio CD
Audio CDs contain music tracks only.
You will recognize Audio CDs by their logo
which is shown.
Unpacking
First check and identify the contents of your DVD-Video
player package.
You should have the following items.
–DVD-Video player
–Remote Control with batteries
–AC power cord
–Audio cable
–Video cable
–SCART cable
–Instructions for use
If any item is damaged or missing, contact your retailer or
Philips.
Keep the packaging materials; you may need them to
transport your player in the future.
Safety Information
¶Do not expose the system to excessive moisture, rain, sand
or heat sources.
¶Place the player on a firm, flat surface.
¶Keep the player away from domestic heating equipment
and direct sunlight.
¶In a cabinet, allow about 2.5 cm (1 inch) of free space all
around the player for adequate ventilation.
¶If the DVD-Video player cannot read CDs/DVDs correctly,
use a commonly available cleaning CD/DVD to clean the
lens before taking the DVD-Video player to be repaired.
Other cleaning methods may destroy the lens.Always keep
the tray closed to avoid dust on the lens.
¶The lens may cloud over when the DVD-Video player is
suddenly moved from cold to warm surroundings. Playing a
CD/DVD is not possible then. Leave the DVD-Video player
in a warm environment until the moisture evaporates.
Cleaning discs
Some problems occur because the disc inside the player is
dirty.To avoid these problems clean your discs regularly, in
the following way:
¶When a disc becomes dirty, clean it with a cleaning cloth.
Wipe the disc from the center out.
Caution: Do not use solvents such as benzine,
thinner, commercially available cleaners, or anti-
static spray intended for analog discs.
INTRODUCTION

11
English
Functional Overview
Front panel
TIMETRACKTOTAL
CHAPTER
TITLE TRACK
PLAY
PREV
STOP
NEXT
SOUND
OPEN
/CLOSE PAUSE
TRACKTITLE
SCAN CHAPTER
CD
SHUFFLE
V
REPEAT
-BA
STANDBY-ON
DVD 761
DVD/VIDEO CD/CD PLAYER
min.
PHONES - LEVEL
STANDBY-ON –switches the player to Standby mode or ON
Standby indicator–lights red when the player is in Standby
mode
Display –shows the current status of the player
T –NEXT title/chapter/track
2 PLAY –starts video/audio play
S –PREVious title/chapter/track
SOUND
–selects Stereo, Dolby Surround or 3D-Sound
Disc Tray
/OPEN/CLOSE –opens/closes the disc tray
;PAUSE –interrupts video/audio play or advances
to the next picture frame
9STOP –stops video/audio play
LEVEL –headphone volume control
PHONES –for connecting headphones
FUNCTIONAL OVERVIEW

12
English
Rear panel
L
R(CVBS)
VIDEO OUT
DIG OUT AUDIO OUT S-VIDEO OUT OPT OUT
DIGITAL AUDIO OUT
PCM/MPEG2/AC3/DTS
STEREO OUT
(Y/C)
I
AUX/VCR
IN
II
TV OUT
MAINS
RIGHT SUBW.
REAR
RIGHT
FRONT
LEFT CENTER
MULTICHANNEL AUDIO OUT
REAR
LEFT
FRONT
MAINS (AC) power jack –connect to the power
source
Digital audio out jack (optical)
–connect to digital (optical) equipment
Digital audio out jack (coaxial)
–connect to digital (coaxial) equipment
Audio / L/R (Left/Right)
–connect to an amplifier, receiver or stereo system
TV OUT (TV)
–connect to a TV with SCART
AUX/VCR (SCART)
–connect to a VCR
S-Video Out (S-Video)
–connect to a TV with S-Video (Y/C) inputs
Video Out (CVBS)
–connect to a TV with CVBS video inputs
Multichannel connections
(For connection to a multichannel receiver)
–center speaker connection
–subwoofer connection
–front speakers connections
–surround speakers connections
Caution: Do not touch the inner pins of the jacks
on the rear panel connectors. Electrostatic
discharge may cause permanent damage to the
unit.
FUNCTIONAL OVERVIEW

13
English
Display
FUNCTIONAL OVERVIEW
TRACKTITLE
SCAN
TIMETRACKTOTAL
CHAPTER
CD
SHUFFLE
CHAPTER
TITLE TRACK
V
REPEAT
-BA
Front (left and right) speakers active
Center speaker active
Test tone active
Active audio format
Surround (left and right) speakers active
Subwoofer active
DVD inserted
CD
V
Video CD or Audio CD inserted
Indicates current player function: Play, Pause, Search, etc.
TITLE
DVDTITLE number
CHAPTER
DVD CHAPTER number
TRACK
VCD/CDTRACK number
TIMETRACK
TRACK TIME in hours, minutes and seconds
TIMETOTAL
TOTAL TIME in hours, minutes and seconds
REPEAT CHAPTER/TITLE/TRACK active
Remote control active (flashing)
FTS active
SCAN
SCAN active
REPEAT
-BA
REPEAT A-B active
SHUFFLE
SHUFFLE active

14
English
Remote control (Universal)
TV MUTE
–DVD-mode: selects Stereo, Dolby
Surround, 3D Sound
reproduction
–TV-mode: mute ON/OFF
DVD/TV switch
–DVD mode/TV mode selector**
0-9 numerical key pad
RETURN
–go back to previous menu
OK
–acknowledge menu selection
QO
–search backward* / previous
chapter or track
2
–play
RP
–search forward* / next chapter or
track
;
–pause playback temporarily /
frame-by-frame playback
9
–stop
x
–slow motion
STANDBY-ON
REPEAT
–repeat chapter, track, title, disc
REPEAT A-B
–repeat sequence
SHUFFLE
–playback tracks in random order
SCAN
–playback of the first 10 seconds of
each chapter within a title (DVD)
or the first 10 seconds of each
track on a disc (VCD/CD)
MENU DVD
–access menu of a DVD
MENU OSD
–access or remove On-screen
display
–bit rate indicator*
PROG +/-
–DVD mode: up/down cursor
movement
–TV mode: Program up/down
VOL +/-
–DVD mode: left/right cursor
movement
–TV mode: Volume up/down
Z
–subtitle language selector
Y
–audio language selector
T
–select title
C
–select chapter
c
–activate FTS
}
–select DVD camera angle
a
–enlarge video image
* Press key for about 2 seconds
** Press and hold while you press mute/VOL/PROG keys for compatible TVs
Please refer to list of Universal Remote Control Setup Codes
FUNCTIONAL OVERVIEW

15
English
On Screen Display Information
Menu bar/Status window
VPersonal Preferences
WTitle/Track
XChapter/Index
YAudio language
ZSubtitle language
}Angle
aZoom
bColor Settings (Smart Picture)
cVideo Program
dSound
ePicture by Picture
fSlow motion
gFast motion
hTime search
Status window icons
The status window displays the current status of the player
and appears with the first part of the menu bar. (You must
activate this in the Features Menu - see Personal
Preferences for details).
General
Disc type
Tray status
Default screen
The default screen is displayed when the player is in STOP
mode.
It may contain a ‘Status Window’and a ‘Temporary
Feedback Field’.This gives information concerning
prohibited actions, playback modes, available angles, etc.
Temporary Feedback Field
icons
Scan
Repeat All
RepeatTitle
RepeatTrack
Repeat Chapter
Shuffle
Shuffle Repeat
Repeat A to end
Repeat A-B
Angle
Child Lock On
Child Safe
Resume
Action prohibited
ONSCREEN DISPLAY INFORMATION

16
English
Preparation
General notes
¶Depending on yourTV and other equipment you wish to
connect, there are various ways you could connect the
player. Possible connections are shown in the following
drawings.
¶Please refer to the manuals of your TV,VCR, Stereo System
or other devices as necessary to make the best
connections.
¶Do not connect your DVD-player via your VCR.The video
quality could be distorted by the copy protection system.
¶For better sound reproduction, connect the player’s audio
out jacks to the audio in jacks of your amplifier, receiver,
stereo or A/V equipment. See ‘Connecting to optional
equipment’.
Caution: Do not connect the player’s audio out
jack to the phono in jack of your audio system.
Connecting to a TV
1Connect the SCART to the corresponding connector on
theTV using the SCART cable supplied (A).
If yourTV is not equipped with a SCART you can select
one of the following alterative connections:
S-Video (Y/C) connection
1Connect the S-Video jack on the DVD-player to the S-
Video in jack on theTV using an optional S-Video cable (B).
2Connect the audio Left and Right out jacks to the audio
left/right in jacks on the TV (D).
Video CVBS connection
1Connect theVideo out (CVBS) jack to the video in jack on
theTV using the video cable supplied (C).
2Connect the audio Left and Right out jacks to the audio
left/right in jacks on the TV ((D).
TV
MAINS
L
R(CVBS) (Y/C)
VIDEO OUT S-VIDEO OUT
DIG OUT AUDIO
STEREO OUT VIDEO OUT
I
AUX- I /O
II
TO TV- I /O
OPT OUT
RIGHT SUBW.
REAR
RIGHT
FRONT
LEFT CENTER
MULTICHANNEL AUDIO OUT
DIGITAL AUDIO OUT
PCM/MPEG2/AC3/DTS
REAR
LEFT
FRONT
AB
C
D
Connecting to optional
equipment
Connecting to an amplifier equipped with
two channel analog stereo
1Connect the audio Left and Right out jacks of the DVD
player to the audio left and right in jack on your amplifier,
receiver or stereo system, using the optional audio cable
(E).
Connecting to an amplifier equipped with
two channel digital stereo (PCM)
1Connect the player’s digital audio out jack (optical Gor
coaxial F) to the corresponding in jack on your amplifier.
Use an optional digital (optical Gor coaxial F) audio cable.
2You will need to activate the player’s digital output (see
‘Personal Preferences’).
Connecting to an A/V receiver equipped
with a multi-channel decoder (Dolby
Digital™(AC-3), MPEG 2 and DTS)
Digital Multi-channel sound
Digital multi-channel connection provides the best sound
quality. For this you need a multi-channel A/V receiver that
supports one or more of the audio formats supported by
your DVD player (MPEG 2, Dolby Digital™(AC-3) and
DTS). Check the receiver manual and the logos on the
front of the receiver.
1Connect the DVD player’s digital audio output (optical G
or coaxial F) to the corresponding input on the receiver
using an optional digital (optical Gor coaxial F) audio cable.
2You will need to activate the player’s digital output (see
‘Personal Preferences’).
All
PREPARATION

17
English
Note:
– If the audio format of the digital output does not match the
capabilities of your receiver, the receiver will produce a strong,
distorted sound or no sound at all.
– The selected audio format of the DVD is displayed in the
Status Window when the Menu OSD is activated or Audio
button is activated.
– Six Channel Digital Surround Sound via digital connection
can only be obtained if your receiver is equipped with a Digital
Multi-channel decoder.
– To see the selected audio format of the current DVD in the
Status Window, press the MENU OSD or the Audio Language
selector button.
MAINS
L
R(CVBS) (Y/C)
VIDEO OUT S-VIDEO OUT
DIG OUT AUDIO
STEREO OUT VIDEO OUT
I
AUX- I /O
II
TO TV- I /O
OPT OUT
RIGHT SUBW.
REAR
RIGHT
FRONT
LEFT CENTER
MULTICHANNEL AUDIO OUT
DIGITAL AUDIO OUT
PCM/MPEG2/AC3/DTS
REAR
LEFT
FRONT
TV
AMPLIFIER
EGF
Cinemalink (on SCART)
This DVD player is equipped with cinemalink feature (from
Philips) which allows a more complete control of your
home audio/video (AV) equipment.
Cinemalink interconnection plug & play will enable the AV
system to recognise the users intention and automatically
switch the necessary controls or input source accordingly.
This will reduce the necessity of having multiple control
inputs for all AV equipments (eg.TV and Amplifier).
Analog connection to a multi-channel A/V
receiver with 6 CH connectors
This DVD player contains a multi-channel decoder.This
enables playback of DVDs recorded in Multi-channel
Surround without the need for an optional decoder.
1Connect the audio out jacks for Center speaker and
Subwoofer connection (I) to the corresponding in jacks on
your receiver.
Note:
– If the subwoofer is equipped with its own amplifier, the
Subwoofer connection should be connected to the subwoofer
directly.
Connect the audio Left and Right out jacks for Front
speaker connection (H) to the corresponding in jack
sockets on your receiver.
Connect the audio Left and Right out jacks for Surround
speaker connection (J) to the corresponding in jacks on
your receiver.
2Make the appropriate Sound settings for Analog Output
and Speaker Settings in the Personal Preferences menu.
MAINS
L
R(CVBS) (Y/C)
VIDEO OUT S-VIDEO OUT
DIG OUT AUDIO
STEREO OUT VIDEO OUT
I
AUX- I /O
II
TO TV- I /O
OPT OUT
RIGHT SUBW.
REAR
RIGHT
FRONT
LEFT CENTER
MULTICHANNEL AUDIO OUT
DIGITAL AUDIO OUT
PCM/MPEG2/AC3/DTS
REAR
LEFT
FRONT
TV
AMPLIFIER
H
JI
Connecting to an amplifier equipped with
Dolby Surround™
Dolby Surround sound
1Connect the player to the TV, then connect the player’s
audio Left and Right out jacks to the corresponding in jacks
on the Dolby Surround™Audio/Video receiver, using the
audio/video cable supplied (D).
If your amplifier is equipped with a Dolby
Digital™decoder,
¶Connect the player as described in ‘Connecting to an A/V
receiver with multi-channel decoder’.
If yourTV is equipped with a Dolby Surround™
decoder,
¶Connect the player to the TV as described in ‘Connecting
to a TV’.
Remote control battery
installation
Loading the batteries
1Open the battery compartment cover.
2Insert batteries as indicated inside the battery
compartment.
3Close the cover.
Caution: Do not mix old and new batteries. Never
mix different types of batteries (standard, alkaline,
etc.)
PREPARATION

18
English
NTSC/PAL Settings
You can switch the NTSC/PAL setting of the DVD player to
match the video signal of yourTV.This setting only affects
the television’s on-screen display that shows the stop and
setup modes.You may select either NTSC or PAL.To
change the DVD player setting to PAL or NTSC, follow the
steps below.
1Unplug the DVD player from the mains.
2Press and hold 9and Ton the front of the DVD player.
While holding 9and T, plug in the mains.
3After PAL or NTSC appears on the display panel of the
DVD player, release 9and Tat the same time.The PAL
or NTSC that appears on the display panel indicates the
current setting.
4To change the setting, press Twithin three seconds.The
new setting (PAL or NTSC) will appear on the display
panel.
General explanation
About this manual
This manual gives the basic instructions for operating this
DVD player. Some DVDs require specific operation or
allow only limited operation during playback. In these cases,
the player may not respond to all operating commands.
When this occurs, please refer to the instructions contained
with the DVD. When the symbol Äappears on the TV
screen, the operation is not permitted by the player or the
disc.
Remote control operation
¶Unless otherwise stated, all operations can be carried out
with the remote control. Always point the remote control
directly at the player, making sure there are no obstructions
in the path of the infrared beam.
When there are corresponding keys on the front panel of
the player, they can also be used.
Menu bar operation
¶A number of operations can be carried out via the menu
bar on the screen.The menu bar can be accessed by
pressing any of the following keys on the remote control:
MENU OSD,T, C, Angle, Audio Language, Subtitle Language
and Zoom.
¶Pressing MENU OSD while the menu bar is displayed will
clear the menu bar from the screen.
¶When selecting an item in the menu bar, the selected item
will be highlighted and the appropriate cursor keys to
operate this item will be displayed below the icon.
¶< or > indicates that more items are available at the left/
right of the menu bar. Press tor uto select these items.
Turning On the power
1Switch on theTV and select the video input channel for
your DVD- Video player.
2Press STANDBY-ON button.
DVD 711
DVD/VIDEO CD/CD P
L
STANDBY-ON
DVD 761
Initial Setup (Virgin Mode)
General
In ‘Initial Setup’you may have to set your preferences for
some of the player’s features. (not applicable for all models)
Operation
After switching on the player for the very first time, the
‘Initial Setup Screen’will appear.
The menu for the first item to be set is displayed and the
first option is highlighted.
¶Use the wvkeys to go through the options in the menu.
The icon of the selected option will be highlighted.
¶Use OK to confirm your selection and to go to the next
menu.
Note:
– Preferences have to be set in the order in which the item
menus will appear on the screen.
– The ‘Initial Setup’ screen will only disappear after the
settings for the last item have been confirmed.
– If any keys other than wvor OK are pressed, Äwill
appear on the screen.
– If the player is switched off while setting personal
preferences, all preferences have to be set again after switching
the player on again.
PREPARATION

19
English
The following items may have to be set in Initial
Setup:
Menu language
You can choose from different languages.The On Screen
Menus will be displayed in the language you choose.
Audio language
You can choose from different languages.The sound will be
in the language you choose if it is available on the disc in
play. If the language you select is not available, speech will
revert to the first spoken language on the disc.
Subtitle language
You can choose from different languages.The subtitles will
be in the language you choose if it is available on the disc in
play. If the language you select is not available, subtitles will
revert to the first subtitle language on the disc.
Initial Setup
Menu language
English
Español
Français
Português
Chinese
Malay
Initial Setup
Audio language
English
Español
Français
Português
Russian
Polish
Initial Setup
Subtitle language
English
Español
Français
Português
Russian
Polish
TV Shape
If you have a wide screen (16:9)TV, select 16:9.
If you have a regular (4:3)TV, select 4:3.
If you have a 4:3TV, you can also select between:
Letterbox for a ‘wide-screen’picture with black bars top
and bottom, or Pan Scan, for a full-height picture with the
sides trimmed. If a disc has Pan Scan, the picture then
moves (scans) horizontally to keep the main action on the
screen.
Country
Select your country.This is used as input for the ‘Parental
Control’feature (see ‘Access Control’).
Note:
– All these items may have to be set during ‘Initial Setup’.
After that, they can always be changed in the Personal
Preferences Menu.
Personal Preferences
You can set your personal preferences for some of the
player features.
General operation:
¶Press MENU OSD on the remote control.
¶Select Vin the menu bar.
➜The Personal Preferences menu appears.
¶Use the tuwvkeys to toggle through the menus,
submenus and submenu options.
➜When a menu item is selected, the cursor keys (on the
remote control) to operate the item are displayed next to
the item.
¶Press OK to confirm and return to the main menu.
The following items can be adapted:
Picture
–TV Shape
See ‘Initial Setup’
–Black level shift (NTSC only)
Select ON for adapting the color dynamics to obtain richer
contrasts.
–Video shift
The factory centers the video on your screen. Use this
setting to personalize the position of the picture on your
TV by scrolling it to the left or right.
–Color settings (SCART connection)
You can select one of five predefined sets of color settings
(SCART connection only) and one set (Personal) which
you can define yourself.
PREPARATION

20
English
–Personal color
Allows you to fine-tune the selected color settings (SCART
connection only) saturation, brightness and contrast.
Sound
–Digital output
Factory setting:ALL.This means that both coaxial and
optical outputs are switched on. If you are not connecting
equipment with a digital input, change the setting to OFF.
If your equipment doesn't include a digital multi-channel
decoder, set the digital output to PCM (Pulse Code
Modulation). Both coaxial and optical outputs are switched
on.
–Analog output
Select Stereo, Dolby Surround or 3D sound.
–Night Mode
Optimizes the dynamics of the sound with low volume
playback.
–Speaker settings
Allows you to select speaker settings, volume balance and
delay time and to test the speaker settings.
Speaker settings are only active on the Analog Multi-
Channel Output. (See appendix)
–Karaoke vocal
Put this setting to ON only when a multi-channel karaoke
DVD is being played.The karaoke channels on the disc will
then be mixed into a normal stereo sound.
Language
Select the required Menu,Audio and Subtitle language. See
‘Initial Setup’.
Audio language and Subtitle language can also be adapted
via the Menu bar on the screen.
Features
–Access Control
Access Control contains the following features:
Child Lock - When Child Lock is set to ON, a 4-digit code
needs to be entered in order to play discs.
Parental control - Allows the conditional presentation of
DVDs containing Parental Control information (see ‘Access
Control’).
–Status Window
Displays the current status of the player and is displayed
with the menu bar. When disc playback is stopped, it is
displayed with the ‘Temporary Feedback Field’in the default
screen. See ‘On-Screen Display’information;
Factory setting is ON. Select OFF to suppress display of the
Status Window.
–Bit Rate Indicator
When activated, the bit rate for video, audio as well as total
bit rate is displayed.This is only applicable during playback
of DVD and SVCD discs
–Beeper
The beeper can be set to ON or OFF.
PREPARATION