Philips DVP3111/55 User manual

TABLE OF CONTENTS
Page
Version 1.1
Service Manual
. Technical Specifications…………....………………………..............1-2
. Safety Instruction, Warning & Notes….……………………....….....1-3
. Mechanical and Dismantling Instructions…………........................3-1
. Software Version & Upgrades, Region Code Cha nge..……..........4-1
. Trouble Shooting Chart…………………..……………………………
.5-1
. Wiring Diagram………………………………………..………..….….6-1
. Electrical Diagrams and Print-layouts..….…………………....….…7-1
. Packing, Set Mechanical Exploded view & Part list.………..….….8-1
©Copyright 2009 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
All rights reserved. No part of this publication may be reproduced, stored in aretrieval system or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise
without the prior permission of Philips.
CLASS 1
LASER PRODUCT
PHILIPS
GB
. DFU Instruction..............................................................................2-1
. Revision List..................................................................................9-1
DVP3111 DVP3300(X)
Published by FK-0940 BU AVM Printed in The Netherlands Subject to modification 3141 785 34461
DVP3111/55
DVP3300/93
DVP3300/96
DVP3111X/77

Video format
Digital compression:•
DVD/SVCD/VCD/DivX•
Horizontal resolution:•
DVD: 720 pixels (50 Hz); 720 pixels•
(60 Hz)
VCD: 352 pixels (50 Hz); 352 pixels•
(60 Hz)
Vertical resolution:•
DVD: 576 pixels (50 Hz); 480 pixels•
(60 Hz)
VCD: 288 lines (50 Hz); 240 lines•
(60 Hz)
Audio performance
DA converter: 24 bits, 192 kHz•
Frequency response:•
DVD: 4 Hz - 22 kHz (48 kHz); 4 Hz -•
44 kHz (96 kHz)
SVCD: 4 Hz - 20 kHz (44.1 kHz); 4•
Hz - 22 kHz (48 kHz)
CD/VCD: 4 Hz - 20 kHz (44.1 kHz)•
Signal-Noise (1 kHz): > 90 dB•
(A-weighted)
Dynamic range (1 kHz): > 80 dB•
(A-weighted)
Crosstalk (1 kHz): > 90 dB•
Distortion/noise (1 kHz): > 65 dB•
MP3: MPEG L3•
Audio format
Digital:•
MPEG/AC-3: Compressed digital (16,•
20, 24 bits, fs 44.1, 48, 96 kHz)
MP3: 96, 112, 128, 256 kbps &•
variable bit rate, fs 32, 44.1, 48 kHz
Analog sound stereo•
Dolby surround compatible downmix•
from Dolby Digital multi-channel sound
Connections
Video output: Cinch (yellow)•
Audio output (L+R): Cinch (white/red)•
Digital output:•
1 coaxial: IEC60958 for CDDA/•
LPCM; IEC61937 for MPEG 1/2,
Dolby Digital
Specifications
Note
Specification and design are subject to change
•
without notice
Accessories supplied
Remote control and batteries•
Audio/Video cables•
Power plug adaptor•
User Manual•
Play media
DVD-Video, Video CD/SVCD, Audio CD,•
CD-R/CD-RW, DVD+R/+RW, DVD-R/-
RW, DivX-CD, Picture CD, MP3-CD
TV standard
Number of lines:•
625 (PAL/50Hz); 525 (NTSC/60Hz)•
Play: Multi-standard (PAL/NTSC)•
Video performance
Video DAC: 12 bits, 108 MHz•
Video output: 1 Vpp ~ 75 ohm•
Main unit
Dimensions (w x h x d): 360 x 37 x 209•
(mm)
Net Weight: approximately 1.3 kg•
Power
Power supply rating: 110 - 240V, 50/60HZ•
Power consumption: <10 W•
Power consumption in standby mode:•
<1 W
Laser specification
Type: Semiconductor laser InGaAIP•
(DVD), AIGaAs (CD)
Wave length: 658 nm (DVD), 790 nm•
(CD)
Output Power: 7.0 mW (DVD), 10.0 mW•
(VCD/CD)
Beam divergence: 60 degrees•
1-2
for DVP3111/55

Video format
Digital compression:•
DVD/SVCD/VCD/DivX•
Horizontal resolution:•
DVD: 720 pixels (50 Hz); 720 pixels•
(60 Hz)
VCD: 352 pixels (50 Hz); 352 pixels•
(60 Hz)
Vertical resolution:•
DVD: 576 pixels (50 Hz); 480 pixels•
(60 Hz)
VCD: 288 lines (50 Hz); 240 lines•
(60 Hz)
Audio performance
DA converter: 24 bits, 192 kHz•
Frequency response:•
DVD: 4 Hz - 22 kHz (48 kHz); 4 Hz -•
44 kHz (96 kHz)
SVCD: 4 Hz - 20 kHz (44.1 kHz); 4•
Hz - 22 kHz (48 kHz)
CD/VCD: 4 Hz - 20 kHz (44.1 kHz)•
Signal-Noise (1 kHz): > 90 dB•
(A-weighted)
Dynamic range (1 kHz): > 80 dB•
(A-weighted)
Crosstalk (1 kHz): > 90 dB•
Distortion/noise (1 kHz): > 65 dB•
MP3: MPEG L3•
Audio format
Digital:•
MPEG/AC-3: Compressed digital (16,•
20, 24 bits, fs 44.1, 48, 96 kHz)
MP3: 96, 112, 128, 256 kbps &•
variable bit rate, fs 32, 44.1, 48 kHz
Analog sound stereo•
Dolby surround compatible downmix•
from Dolby Digital multi-channel sound
Connections
Video output: Cinch (yellow)•
Audio output (L+R): Cinch (white/red)•
Digital output:•
1 coaxial: IEC60958 for CDDA/•
LPCM; IEC61937 for MPEG 1/2,
Dolby Digital
Specifications
Note
Specification and design are subject to change
•
without notice
Accessories supplied
Remote control and batteries•
Audio/Video cables•
User Manual•
Play media
DVD-Video, Video CD/SVCD, Audio CD,•
CD-R/CD-RW, DVD+R/+RW, DVD-
R/-RW, DivX-CD, Picture CD, MP3-CD,
USB flash drive
TV standard
Number of lines:•
625 (PAL/50Hz); 525 (NTSC/60Hz)•
Play: Multi-standard (PAL/NTSC)•
Video performance
Video DAC: 12 bits, 108 MHz•
Video output: 1 Vpp ~ 75 ohm•
1-2
Main unit
Dimensions (w x h x d): 360 x 37 x 209•
(mm)
Net Weight: approximately 1.3 kg•
Power
Power supply rating: 110 - 240V, 50/60HZ•
Power consumption: <10 W•
Power consumption in standby mode:•
<1 W
Laser specification
Type: Semiconductor laser InGaAIP•
(DVD), AIGaAs (CD)
Wave length: 658 nm (DVD), 790 nm•
(CD)
Output Power: 7.0 mW (DVD), 10.0 mW•
(VCD/CD)
Beam divergence: 60 degrees•
for DVP3300(X)/93/96

Safety instruction
1. General safety
Safety regulations require that during a repair:
. Connect the unit to the mains via an isolation transformer.
. Replace safety components indicated by the symbol ,
only by components identical to the original ones. Any
other component substitution (other than original type)
may increase risk of fire or electrical shock hazard.
Safety regulations require that after a repair, you must
return the unit in its original condition. Pay, in particular,
attention to the following points:
. Route the wires/cables correctly, and fix them with the
mounted cable clamps.
. Check the insulation of the mains lead for external
damage.
. Check the electrical DC resistance between the mains
plug and the secondary side:
1) Unplug the mains cord, and connect a wire between
the two pins of the mains plug.
2) Set the mains switch the “on” position (keep the
mains cord unplug).
3) Measure the resistance value between the mains
plug and the front panel, controls, and chassis
bottom.
4) Repair or correct unit when the resistance
measurement is less than 1M
¡
.
5) Verify this, before you return the unit to the
customer/user (ref. UL-standard no. 1492).
6) Switch the unit “off”, and remove the wire between
the two pins of the mains plug.
2.Laser safety
This unit employs a laser. Only qualified service personnel
may remove the cover, or attempt to service this device
(due to possible eye injury).
Laser device unit
Type :SemiconductorlaserGaAlAs
Wavelength : 650nm (DVD)
: 780nm (VCD/CD)
Output power : 7mW (DVD)
:10mW(DVD/CD)
Beam divergence: 60 degree
Note: Use of controls or adjustments or performance of
procedure other than those specified herein, may result in
hazardous radiation exposure. Avoid direct exposure to
beam.
Safet
y
instruction, Warnin
g
& Notes
1-3

Warning
1.General
. All ICs and many other semiconductors are susceptible to
electrostatic discharges (ESD). Careless handing during
repair can reduce life drastically. Make sure that, during
repair, you are at the same potential as the mass of the
set by a wristband with resistance. Keep components and
tools at this same potential. Available ESD protection
equipment:
1) Complete kit ESD3 (small tablemat, wristband,
connection box, extension cable and earth cable)
4822 310 10671.
2) Wristband tester 4822 344 13999.
. Be careful during measurements in the live voltage
section. The primary side of the power supply , including
the heat sink, carries live mains voltage when you
connect the player to the mains (even when the player is
“off”!). It is possible to touch copper tracks and/or
components in this unshielded primary area, when you
service the player. Service personnel must take
precautions to prevent touching this area or components
in this area. A “lighting stroke” and a stripe-marked
printing on the printed wiring board, indicate the primary
side of the power supply.
. Never replace modules, or components, while the unit is
“on”.
2. Laser
. The use of optical instruments with this product, will
increase eye hazard.
. Only qualified service personnel may remove the cover
or attempt to service this device, due to possible eye
injury.
. Repair handing should take place as much as possible
with a disc loaded inside the player.
. Text below is placed inside the unit, on the laser cover
shield:
Notes: Manufactured under licence from Dolby
Laboratories. The double-D symbol is trademarks of Dolby
Laboratories, Inc. All rights reserved.
CAUTION: VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN, AVOID EXPOSURE
TO BEAM.
1-4