Philips DVP3264/12 User manual

·Instruction…………………………………………………...................2-1
·Software Upgrade…………...….……………………….....…............3-1
·Accessory list……...………………………..………...........................4-1
·Revision List………………………………………..….....…................5-1
This simple Service Manual is for " Exchange" Scenario
TABLE OF CONTENTS
Page
3139 785 33404
Version 1.4
DVP3260 DVP3264 DVP3252 DVP5990 DVP3266K DVP5996K
Service Manual
PHILIPS
GB
©Copyright 2008 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
All rights reserved. No part of this publication may be reproduced, stored in aretrieval system or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise
without the prior permission of Philips.
CLASS 1
LASER PRODUCT
Published by KC-ET 0809 Service Audio Printed in The Netherlands Subject to modification
DVP3260/05/12 DVP3260/05(Second Generation)
DVP3264/12 DVP3260/12(Second Generation)
DVP3252/51/75 DVP3264/12(Second Generation)
DVP5990/12/05
DVP3266K/51
DVP5996K/51
Service
DVD Player

How to remove the CD manually from the tray
1. Please do as below instruction in case the tray can not be open:
I. Power off the DVD player.
II. Please gently push the guider and wait until the tray comes out (Figure1).
2-1
Figure 1

Software upgrade
Preparation to upgrade software
1) Start the CD Burning software and create a new CD
project (Data Disc) with the following setting:
Label: DVPXXXX (No need the label name)
File Name: DVPXXXX_XX.BIN
Power on the set and open the tray, then press
<5><5>
to check the File Name.
Note: It is required capital letter for the File System
name
2) Burn the data onto a blank CDR
A. Procedure for software upgrade:
1) Power on the set and insert the prepared Upgrade
CDR.
2) The set will starts reading disc & response with the
following display TV screen:
Upgrade File DETECTED
Upgrade?
Press Play TO START.
3) Press <OK> button to confirm, then screen will
display :
Files coping…
UPGRADING…
4) The upgraded disc will automatically out when files
coping complete, then take out the disc.
5) About 1 minute later, the trace will automatically close
when upgrading complete.
B. Read out the software versions to
confirm upgrading
1) Power on the set and press <Setup>
button on the remote control.
2) Press<1><3><7><9>button to check the
software information.
The software version and other information
are display on the TV screen as follows:
Version XX.XX.XX.XX (Main
version)
SUB-VER XX.XX.XX.XX (software
version of
application
software)
8032 XX.XX.XX.XX
Servo XX.XX.XX.XX (software
version of
Servo)
RISC XX.XX.XX.XX
DSP XX.XX.XX.XX
Region Code X
3-1
Caution: The set must not be power off during
upgrading, Otherwise the Main board will be
damaged entirely.

ItemNo. 12NCNo. Description
RC 996510010908 Remote control for DVP3260/05/12,
DVP3264/12, DVP3260/05/12(Second
Generation) and DVP3264/12 (Second
Generation)
996510012682 Remote control for DVP5990/12/05
996510010908 Remote control for DVP3252/51 and
DVP3252/75
996510010959 Remote control for DVP3266K/51
996510013355 Remote control for DVP5996K/51
AV Cable 996510001106 AV Cable for DVP5990/05/12, DVP3252/51
, DVP3266K/51, DVP5996K/51 and
DVP3252/75
Accessories Spare Parts List
4-1

5-1
Revision List
Version 1.0
﹡
Initial Release
Version 1.1
* Adding DVP3252/51
* Adding DVP5990/12/05
* Update Accessory Spare Part List
Version 1.2
* Adding DVP3266K/51
* Update Accessory Spare Part List
Version 1.3
* Adding DVP5996K/51
* Adding DVP3252/75
* Update Accessory Spare Part List
Version 1.4
* Adding DVP3260/05 (Second Generation, OPU type: IM)
* Adding DVP3260/12 (Second Generation, OPU type: IM)
* Adding DVP3264/12 (Second Generation, OPU type: IM)