Philips DVP3360 User manual

DVP3360
Register your product and get support at
www.philips.com/welcome
EN User manual

2

English
EN 3
Contents
Contents
1 Important 4
Safety and important notice 4
Trademark Notice 5
2 Your DVD player 6
Features highlight 6
Product overview 7
3 Connect 9
Connect video cables 9
Connect audio cables 11
Route audio to other devices 11
Connect USB device 12
Connect to power outlet 12
4 Get started 13
Prepare the remote control 13
Find the correct viewing channel 14
Select menu display language 14
Turn on Progressive Scan 15
Use Philips EasyLink 16
5 Play 17
Play from disc 17
Play video 18
Play music 21
Play photo 23
Play from USB device 24
6 Advanced features 25
Create MP3 les 25
7 Adjust settings 26
General setup 26
Audio setup 27
Video setup 29
Preferences 32
8 Additional information 34
Update software 34
Care 34
9 Specication 35
10 Troubleshooting 36
11 Glossary 38

4EN
This product complies with the radio
interference requirements of the European
Community. This product complies with the
requirements of the following directives and
guidelines: 2006/95/EC, 2004/108/EC.
This product is in compliance with the EEE
directive.
About Progressive Scan
Consumers should note that not all high denition
television sets are fully compatible with this
product and may cause artifacts to be displayed in
the picture. In case of 525 or 625 progressive scan
picture problems, it is recommended that the user
switch the connection to the ‘standard denition’
output. If there are questions regarding our TV set
compatibility with this model 525p and 625p
DVD player, please contact our customer service
center.
Recycle notice
Your product is designed and manufactured
with highly quality material and components,
which can be recycled and reused. When this
crossed-out wheeled bin symbol is attached to
a product, it means the product is covered by
the European Directive 2002/96/EC.
1 Important
Safety and important notice
Warning
• Risk of overheating! Never install the DVD player
in a conned space. Always leave a space of at least
four inches around the DVD player for ventilation.
Ensure the curtains or other objects never cover the
ventilation slots on the DVD player.
Never place the DVD player, remote control or
•
batteries near naked ames or other heat sources,
including direct sunlight.
Only use this DVD player indoors. Keep this DVD
•
player away from water, moisture and liquid-lled
objects.
Never place this DVD player on other electrical
•
equipment.
Keep away from this DVD player during lightning
•
storms.
Where the mains plug or an appliance coupler is
•
used as the disconnect device, the disconnect device
shall remain readily operable.
Visible and invisible laser radiation when open. Avoid
•
exposure to beam.
Mains fuse (U.K. only)
This DVD player is tted with an approved
moulded plug. Should it become necessary to
replace the mains fuse, this must be replaced
with a fuse of the same value as indicated on
the plug (example 10A).
1 Remove fuse cover and fuse.
2 The replacement fuse must comply with BS
1362 and have the ASTA approval mark. If
the fuse is lost, contact your dealer in
order to verify the correct type.
3 Ret the fuse cover.
In order to maintain conformity to the
EMC directive, the mains plug on this
product must not be detached from the
mains cord.

English
EN 5
Important
Trademark Notice
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
Windows Media and the Windows logo are
trademarks, or registered trademarks of
Microsoft Corporation in the United States and/
or other countries.
DivX, DivX Ultra Certied, and associated logos
are trademarks of DivX, Inc. and are used under
license.
Ofcial DivX® Ultra Certied product.
Plays all versions of DivX ® video (including
DivX ® 6) with enhanced playback of DivX®
media les and the DivX® Media Format.
Plays DivX® video with menus, subtitles and
audio tracks.
The USB-IF Logos are trademarks of Universal
Serial Bus Implementers Forum, Inc.
HDMI, and HDMI logo and High-Denition
Multimedia Interface are trademarks or
registered trademarks of HDMI licensing LLC.
Never dispose of your product with other
household waste. Please inform yourself about
the local rules on the separate collection of
electrical and electronic products. The correct
disposal of your old product helps prevent
potentially negative consequences on the
environment and human health.
Your product contains batteries covered by the
European Directive 2006/66/EC, which cannot
be disposed of with normal household waste.
Please inform yourself about the local rules on
separate collection of batteries. The correct
disposal of batteries helps prevent potentially
negative consequences on the environment and
human health.
Copyright notice
This product incorporates copyright protection
technology that is protected by method claims
of certain U.S. patents and other intellectual
property rights owned by Macrovision
Corporation and other rights owners. Use of
this copyright protection technology must be
authorised by Macrovision Corporation, and is
intended for home and other limited viewing
uses only unless otherwise authorised by
Macrovision Corporation. Reverse engineering
or disassembly is prohibited.
Copyright in the U.K.
Recording and playback of material may require
consent. See Copyright Act 1956 and The
Performers’s Protection Acts 1958 to 1972.

6EN
2 Your DVD
player
Congratulations on your purchase, and
welcome to Philips! To fully benet from the
support that Philips offers, register your product
at www.philips.com/welcome.
This DVD player offers higher picture quality
video play for an amazing viewing experience.
Features highlight
Video upscaling to 1080p
You can now watch the DVDs in the highest
picture quality available for your HDTV. This
DVD player offers full high-denition video play
up to 1080p resolution for an amazing viewing
experience. A highly detailed picture and
increased sharpness delivers a more true-to-life
picture.
EasyLink
EasyLink uses the HDMI CEC (Consumer
Electronics Control) industry standard protocol
to share functionality with all HDMI CEC
compliant devices over HDMI. It enables the
connected devices to control each other with a
single remote control.
Note
EasyLink (HDMI CEC) is only applicable with certain•
criteria. Terms and conditions may vary by product.
Consult your product dealer for information.
Philips does not guarantee 100% interoperability
•
with all HDMI CEC devices.
Screen t
View the movie in full screen on any TV with
this DVD player.
Hi speed USB 2.0 link
Simply plug your USB ash drive into the USB
socket to play your MP3/WMA/JPEG/DivX les
to enjoy the music play in superb sound quality.
Create MP3 les
Convert your favourite audio tracks from an
audio CD into MP3 format. The created MP3
les are saved in your USB device.
Region codes
Your DVD player plays discs with the following
region codes.
DVD region code Countries
ALL
Europe
ALL
Russia

English
EN 7
Your DVD player
Product overview
Main unit
a2 (Standby-on)
Turn on the DVD player or switch to•
standby mode.
bDisc compartment
cDisplay panel
dZ (Open/Close)
Open or close the disc compartment.•
eu(Play/Pause)
Start, pause or resume disc play.•
f(USB) socket
Connect a USB ash drive.•
4
31 2 6
5
Remote control
4
3
6
7
9
8
1
5
2
16
17
12
15
13
14
10
11
18
a2 (Standby-On)
Turn on the DVD player or switch to•
standby mode.
Press and hold to turn off the DVD•
player and all HDMI CEC compliant
devices.
bZ (Open/Close)
Open or close the disc compartment.•
cDISC MENU
Access or exit the disc menu.•
Switch to disc mode.•
For VCD/SVCD, turn PBC (Playback•
Control) on or off in PBC mode.

8EN
dv V b B (Navigation buttons)
Navigate through the menus.•
Search fast-forward (• B) or fast-
backward (b). Press repeatedly to
change the search speed.
Search slow-forward (• v) or slow-
backward (V). Press repeatedly to
change the search speed.
e2BACK
Return to the previous display menu.•
For DVD, navigate to the title menu.•
For VCD version 2.0 or SVCD with•
PBC turned on, return to the menu.
fí/ë(Previous/Next)
Skip to the previous or next title,•
chapter, or track.
Press and hold for fast-backward or•
fast-forward search.
g(USB)
Switch to USB mode and display the•
content.
hNumeric buttons
Select an item to play.•
iSUBTITLE
Select DVD or DivX subtitle language.•
j,ZOOM
Fit the picture format to the TV screen.•
Zoom in or out of the picture.•
kREPEAT
Toggle between various repeat modes.•
lREPEAT A-B
Mark the section for repeat play; turn•
off repeat mode.
mAUDIO/CREATE MP3
Select an audio language/channel.•
Access the menu to create MP3.•
nx(Stop)
Stop disc play.•
ou(Play/Pause)
Start, pause or resume disc play.•
pINFO
For disc, display the current status or•
disc information.
For slideshows, display a thumbnail view•
of photo les.
qOK
Conrm an entry or selection.•
rSETUP
Access or exit the setup menu.•

English
EN 9
Connect
3 Connect
Make the following basic connections to use the
DVD player.
Basic connections:
Video cables•
Audio cables•
Optional connections:
Audio to other devices:•
Digital amplier/receiver•
Analogue stereo system•
Note
Refer to the type plate at the rear or bottom of the•
product for identication and supply ratings.
Before you make or change any connections, ensure
•
that all the devices are disconnected from the power
outlet.
Tip
Different types of connectors may be used to•
connect this product to your TV, depending on
availability and your needs. A comprehensive
interactive guide to help you connect your product is
available at www.connectivityguide.philips.com.
Connect video cables
Connect this DVD player to the TV to view
disc play.
Select the best video connection that the TV can
support.
Option 1:• Connect to HDMI socket (for a
HDMI, DVI or HDCP-compliant TV).
Option 2:• Connect to component video
sockets (for a standard TV or Progressive
Scan TV).
Option 3:• Connect to scart socket (for a
standard TV).
Option 4:• Connect to video (CVBS) socket
(for a standard TV).
Note
You must connect this• DVD player directly to a
TV.
Option 1: Connect to HDMI socket
HDMI IN
HDMI OUT
1Connect a HDMI cable (not supplied) to
the HDMI OUT socket on this DVD
player and the HDMI input socket on the
TV.
Use a HDMI-DVI adaptor in case the•
TV has only a DVI connection.
Note
If the device supports HDMI CEC, you can control•
compliant devices with a single remote control (see
chapter ‘Use Philips EasyLink’).
Tip
This type of connections provide best picture quality.•

10 EN
Option 2: Connect to component
video sockets
Pb
COMPONENT
VIDEO IN
Y
Pr
Pb
COMPONENT VIDEO OUT
YPr
1Connect the component video cables (not
supplied) to the Y Pb Pr sockets on this
DVD player and the component video
input sockets on the TV.
If a progressive scan TV is used, you•
may turn on the progressive scan mode
(see chapter ‘Turn on Progressive Scan’
for details).
Tip
The component video input sockets on the TV may•
be labelled as Y Pb/Cb Pr/Cr or YUV.
This type of connection provides good picture
•
quality.
Option 3: Connect to scart socket
1 Connect a scart cable (not supplied) to the
TV OUT socket on this DVD player and
the scart input socket on the TV.
Tip
This type of connection provides good picture•
quality.
Option 4: Connect to video (CVBS)
socket
VIDEO IN
1 Connect a composite video cable (not
supplied) to the VIDEO OUT socket on
this DVD player and the video input socket
on the TV.
Tip
The video input socket on the TV may be labelled as•
A/V IN, VIDEO IN, COMPOSITE or BASEBAND.
This type of connection provides standard picture
•
quality.

English
EN 11
Connect
Connect audio cables
Connect the audio from this DVD player to the
TV to allow sound output through the TV.
AUDIO IN
1 Connect the audio cables (not supplied) to
the AUDIO OUT L/R sockets on this
DVD player and the audio input sockets
on the TV.
Route audio to other devices
Route the sound from this DVD player to other
devices to enhance audio play.
Connect to digital amplier/receiver
DIGITAL IN
COAXIAL
DIGITAL
OUT
1 Connect a coaxial cable (not supplied) to
the COAXIAL/DIGITAL OUT socket on
this DVD player and the COAXIAL/
DIGITAL input socket on the device.
Tip
You can optimise the audio output (see chapter•
‘Adjust settings’ - [ Audio Setup ] > [ Digital Audio
]) for details.

12 EN
Connect to analogue stereo system
AUDIO IN
1 Connect the audio cables (not supplied) to
the AUDIO OUT L/R sockets on this
DVD player and the audio input sockets
on the device.
Tip
You can optimise the audio output (see chapter•
‘Adjust settings’ - [ Audio Setup ] > [ Analogue
Output ]) for details.
Connect USB device
1 Connect the USB ash drive to the
(USB) socket on this DVD player.
Note
This DVD player can only play/view MP3, WMA,•
DivX or JPEG les that are stored on such devices.
Press
• to access the content and play the les.
Connect to power outlet
Warning
Risk of product damage! Ensure that the power•
supply voltage corresponds to the voltage printed on
the back or the underside of the DVD player.
1 Connect the power cord to the power
outlet.
The DVD player is ready to be set up
for use.

English
EN 13
Get started
4 Get started
Prepare the remote control
1 Push to open the battery compartment
cover.
2 Insert two R03 or AAA batteries type with
correct polarity (+/-) as indicated.
3 Close the battery compartment.
Caution
Remove batteries if they are exhausted or if the•
remote control is not to be used for a long time.
Do not mix batteries (old and new or carbon and
•
alkaline, etc.).
Batteries contain chemical substances, they should
•
be disposed off properly.
Navigate through the menu
1 Point the remote control directly at the
remote sensor on this DVD player and
select the desired function.
2 Use the following buttons on the remote
control to navigate through the on-screen
menus.
Button Action
v V Move up or down.
b B Move left or right.
OK Conrm a selection.
Enter numbers.

14 EN
Find the correct viewing
channel
1 Press 2to turn on the DVD player.
2 Turn on the TV and switch to the correct
video-in channel.
You may go to the lowest channel on•
the TV, then press the Channel Down
button on the TV remote control until
you see the Video In channel.
You may press• °button repeatedly
on the TV remote control.
Usually this channel is between the•
lowest and highest channels and may
be called FRONT, A/V IN, VIDEO, etc..
Tip
See the TV user manual on how to select the correct•
input on the TV.
If the audio output of this DVD player is routed
•
to other audio device (such as audio system
or receiver), turn on the audio device to the
appropriate audio input channel. Refer to the device
user manual for details.
Select menu display language
Note
You can skip this setting if this DVD player is•
connected to a HDMI CEC compliant TV. It switches
automatically to the same OSD menu language as
per your TV setting.
1 Press SETUP.
[ General Setup ] menu is displayed.
2 Select [ OSD Language ], then press B.
Nederlands
Auto Standby
DivX(R) VOD Code
OSD Language
Disc Lock
Sleep Timer
General Setup
Auto (Eng)
English
Français
Deutsch
Italiano
Español
Português
The language options are different•
depending on your country or region.
It may not correspond to the illustration
shown here.
3 Press vV to select a language, then press
OK.
Tip
You can set the default language for DVD audio•
and disc menu, see chapter ‘Adjust settings’ - [
Preferences ] for details.

English
EN 15
Get started
Turn on Progressive Scan
Connect a progressive scan TV with
component video sockets (see chapter
‘Connect video cables - Option 2: Connect to
component video sockets’ for details).
1 Turn on the TV to the correct viewing
channel for this DVD player.
2 Press SETUP.
3 Press Vto select [ Video Setup ].
4 Select [ Component Video ] > [
Interlaced ], then press OK.
5 Select [ Progressive ] > [ On ], then press
OK.
A warning message is displayed.
Video Setup
Component Video
Picture Setting
TV Display
TV System
Progressive
On
Off
HD JPEG
HDMI Setup
6 To proceed, select [ OK ] and press OK.
The progressive setup is complete.
Note
If a blank/distorted screen is displayed, wait for 15•
seconds for the auto recover.
If no picture displayed, turn off the progressive scan
•
mode as follows:
1) Press Z to open the disc compartment.
2) Press the numeric button ‘1’.
7 To exit the menu, press SETUP.
8 You can now turn on the progressive scan
mode on the TV (see the TV user manual).
Note
The progressive scan setting will not be available•
when the HDMI video signal is detected.
During play, when progressive scan mode is on for
•
both this DVD player and the TV, distorted picture
may display. Turn off the progressive scan feature on
both this DVD player and the TV.

16 EN
Use Philips EasyLink
The DVD player supports Philips EasyLink,
which uses the HDMI CEC (Consumer
Electronics Control) protocol. EasyLink-
compliant devices that are connected through
HDMI connectors can be controlled by a single
remote control.
Philips does not guarantee 100% interoperability
with all HDMI CEC devices.
1 Turn on the HDMI CEC operations on the
TV and other connected devices. See TVs/
devices manual for details.
2 You can now enjoy the following Philips
EasyLink controls.
One-touch play
When you press the STANDBY button, it turns
on the TV and this DVD player, then video disc
play starts.
To enable One-touch play, a video disc•
must be placed in the disc compartment
before operation.
One-touch standby
When you press and hold the STANDBY button,
all connected HDMI CEC devices switch to
standby mode simultaneously.
Tip
The default setting for EasyLink features is on. You•
can change the default setting, see chapter ‘Adjust
settings’ - [ Video Setup ] > [ HDMI Setup ] >[
EasyLink Setup ] for details.

English
EN 17
Play
5 Play
Play from disc
Note
DVDs and DVD players are designed with regional•
restrictions. Ensure that the DVD video you play is
for the same region zone as the player (indicated on
its back).
This DVD player can support play of the following
•
le formats: MP3/WMA/JPEG/DivX.
To play DVD-R, DVD+R or DVD-RW, the disc must
•
be nalised.
Play a disc
Caution
Never place any objects other than discs into the•
disc compartment.
1 Press Zto open the disc compartment.
2 Insert a disc with its label facing up.
For double-sided disc, load the side to•
play faces up.
3 Press Zto close the disc compartment
and start disc play.
To view disc play, turn on the TV to•
the correct viewing channel for this
DVD player.
4 To stop disc play, press x.
Tip
If the password entry menu is displayed, you have to•
enter the password before it can be played.
If you pause or stop a disc for about 5 minutes, the
•
screen saver activates. To deactivate the screen
saver, press DISC MENU.
After you pause or stop a disc, if no buttons
•
are pressed within 15 minutes, this DVD player
automatically switches to standby mode.

18 EN
Play video
Note
For video disc, play always resumes from the point•
where it was last stopped. To start play from the
beginning, press íwhile the message is displayed.
Control a title
1 Play a title.
2 Use the remote control to control the title.
Button Action
uStart, pause or resume disc
play.
xStop disc play.
ëSkip to the next title or
chapter.
íSkip to the beginning of the
current title or chapter.
Press twice to jump to the•
previous title or chapter.
m,M Searches fast-forward (M)
or fast-backward (m).
Press repeatedly to change•
the search speed.
v,V Searches slow-forward (v) or
slow-backward (V).
Press repeatedly to change•
the search speed.
For VCD/SVCD, slow-•
backward search is not
possible.
Change video play
1 Play a title.
2 Use the remote control to change the
video play.
Button Action
AUDIO/
CREATE MP3
Change audio language.
Only applicable to discs•
with multiple audio
language or channel.
SUBTITLE Change subtitle language.
Only applicable to discs•
with multiple subtitle
language.
REPEAT Select or turn off repeat
mode.
Repeat options vary•
depending on the disc
type.
For VCD/ SVCD, repeat•
play is only possible if the
PBC mode is turned off.
,ZOOM
(Screen Fit)
Fit the picture format to the
TV screen.
Press repeatedly until the•
image is scaled to t to
the TV screen.
,ZOOM Toggle between screen
aspect ratio and different
zoom factor.
To pan through the•
zoomed image, press the
navigation buttons.
INFO Display the current status or
disc information.
You can change the video•
play options here without
interrupting disc play.

English
EN 19
Play
Note
Some operations may not work with some discs. See
•
the information accompanying the disc for details..
Access DVD menu
1 Press DISC MENU to access disc main menu.
2 Select a play option, then press OK.
In some menus, press the• numeric
buttons to input your selection.
To return to the title menu during play,•
press 2BACK.
Access VCD menu
The PBC (Playback Control) for VCD/SVCD is
turned on by default in the factory. When you
load in a VCD/SVCD, the contents menu is
displayed.
1 Press numeric buttons to select a play
option, then press OK to start play.
If PBC is off, it skips the menu and starts•
play from the rst track.
During play, you can press• 2BACK to
return to the menu (if the PBC mode is
on).
Tip
The default setting for PBC is on. You can change the•
default setting, see chapter ‘Adjust settings’ -
[ Preferences ] > [ PBC ] for details.
Preview disc contents
1 During play, press INFO.
The disc status menu is displayed.
2 Select [ Preview ], then press B.
DVD
Select Digest Type:
Title Digest
Chapter Digest
Title Interval
Chapter Interval
VCD/SVCD
Select Digest Type:
Track Digest
Disc Interval
Track Interval
3 Select a preview option, then press OK.
A six thumbnails preview screen is
displayed.
To go to the next/previous preview•
screen, pressí/ë.
To start play, press• OK at the selected
thumbnail picture.

20 EN
Quick skip play to a specic time
1 During play, press INFO.
The disc status menu is displayed.
2 Select the current elapsed playing time,
then press B.
[ TT Time ]• (title time)
[ CH Time ]• (chapter time)
[ Disc Time ]• (disc time)
[ Track Time ]• (track time)
3 Press the numeric buttons to change the
time where you want to skip to.
Display play time
1 During play, press INFO.
The disc status menu is displayed.
2 Select [ Time Disp ], then press B.
The display options are different
depending on the disc type.
Option Action
[ Title Elapsed ]
/ [ Chapter
Elapsed ]
Display DVD title or chapter
elapsed play time.
[ Title Remain ]
/ [Chapter
Remain ]
Display DVD title or chapter
remaining play time
[ Total Elapsed
] / [Single
Elapsed ]
Display VCD/SVCD disc or
track elapsed play time.
[ Total Remain
] / [Single
Remain ]
Display VCD/SVCD disc or
track remaining play time.
3 Select an option, then press OK.
View DVD play from different angles
1 During play, press INFO.
The disc status menu is displayed.
2 Select [ Angle ], then press B.
3 Press the numeric buttons to change the
angle.
Play changes to the selected angle.
Note
Only applicable to discs contain sequences recorded•
from different camera angles.
Set repeat play for a specic section
1 During play, press REPEAT A-B at the
start point.
2 Press REPEAT A-B again to set the end
point.
Repeat play starts.
3 To cancel repeat play, press REPEAT A-B
again.
Note
The marked section for repeat play is only possible•
within a title or track.