Philips DVP3727 User manual

DVD VIDEO PLAYER
Read your Quick Start Guide and/or User Manual first for quick tips
that make using your Philips product more enjoyable.
Register your product and get support
at www.philips.com/welcome
DVP3126
DVP3727
DVD VIDEO PLAYER
User Manual 6
dvp3126-3727_94_eng.indd 1dvp3126-3727_94_eng.indd 1 2007-09-04 2:28:43 PM2007-09-04 2:28:43 PM

2
This product incorporates copyright protection
technology that is protected by method claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection
technology must be authorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise authorized
by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
dvp3126-3727_94_eng.indd 2dvp3126-3727_94_eng.indd 2 2007-09-04 2:28:44 PM2007-09-04 2:28:44 PM

English
Bahasa Melayu
Index
English ------------------------------------------6
dvp3126-3727_94_eng.indd 3dvp3126-3727_94_eng.indd 3 2007-09-04 2:28:45 PM2007-09-04 2:28:45 PM

English
4
LASER
Type Semiconductor laser
InGaAlP (DVD)
AIGaAs (CD)
Wave length 658 nm (DVD)
790 nm (CD)
Output Power 7.0 mW (DVD)
10.0 mW (VCD/CD)
Beam divergence 60 degrees
General Information
Environmental Information
All unnecessary packaging has been
omitted. The packaging has been made
easy to separate into two materials;
cardboard (box) and polyethylene (bags,
protective foam sheet).
Your DVD player consists of materials
which can be recycled and reused if
disassembled by a specialised company.
Please observe the local regulations
regarding the disposal of packaging
materials, exhausted batteries and old
equipment.
Laser Safety
This unit employs a laser. Due to possible
eye injury, only a qualied service person
should remove the cover or attempt to
service this device.
NOTE:
Pictures shown maybe different
between countries.
CAUTION:
WARNING LOCATION: ON THE
BACKPLATE OF THE SET
NEVER MAKE OR CHANGE
CONNECTIONS WITH THE
POWER SWITCHED ON.
For Customer Use:
Read carefully the information located at
the bottom or rear of your DVD Video
player and enter below the Serial No.
Retain this information for future
reference.
Model No. DVP3126/DVP3727
Serial No. ___________________
Specications are subject to change without
notice. Trademarks are the property of
Koninklijke Philips Electronics N.V. or their
respective owners.
Windows Media and the Windows logo
are trademarks, or registered
trademarks of Microsoft Corporation
in the United States and/or other
countries.
Manufactured under license from
Dolby Laboratories, Dolby
and the double-D symbol are
trademarks of Dolby Laboratories.
logo.indd 1 2006-03-21 10:25:36 AM
dvp3126-3727_94_eng.indd 4dvp3126-3727_94_eng.indd 4 2007-09-04 2:28:45 PM2007-09-04 2:28:45 PM

English
5
Language Code
dvp3126-3727_94_eng.indd 5dvp3126-3727_94_eng.indd 5 2007-09-04 2:28:45 PM2007-09-04 2:28:45 PM

English
6
Contents
Care and Safety Information
Setup .............................................................................................................................................................8
Cleaning discs .............................................................................................................................................8
General Information
Accessories supplied ................................................................................................................................9
Region codes...............................................................................................................................................9
Connections
Connecting to television.......................................................................................... 10-11
Using Composite Video jacks (CVBS).............................................................................................. 10
Using Component Video jacks (YPbPr)........................................................................................... 10
Using an accessory RF modulator ......................................................................................................11
Connecting the power cord...........................................................................................12
Optional connections
Connecting to a Multi-channel Receiver .....................................................................12
Receiver has a Dolby Digital decorder .......................................................................................................12
Connecting to a stereo system .....................................................................................13
Stereo system has right/left Audio In jacks ....................................................................................13
Connecting to a digital AV receiver.............................................................................13
Receiver has a PCM, Dolby Digital or MPEG decoder................................................................ 13
Product Overview
Front and Rear panels ....................................................................................................14
Remote Control ............................................................................................................. 15
Getting Started
Step 1: Inserting Batteries.............................................................................................16
Using the remote control to operate the system......................................................................... 16
Step 2: Finding your viewing channel...........................................................................16
Step 3: Setting up Progressive Scan feature...............................................................17
Step 4: Selecting the matching color system ............................................................ 18
Step 5: Setting the language .........................................................................................19
On-screen display (OSD) language.................................................................................................... 19
Audio, Subtitle and DVD menu languages....................................................................................... 19
Playback from Disc
Playable discs.................................................................................................................. 20
Supported formats................................................................................................................................. 20
Playback Features
Starting disc playback ................................................................................................... 21
Basic playback controls................................................................................................. 21
Pausing playback...................................................................................................................................... 21
Selecting title/chapter/track ................................................................................................................ 21
Stopping playback................................................................................................................................... 21
Operations for video playback .................................................................................... 22
Using the Disc Menu .............................................................................................................................22
Zooming in ............................................................................................................................................... 22
Resuming playback from the last stopped point............................................................................ 22
Slow Motion............................................................................................................................................. 22
Forward / Reverse Searching .............................................................................................................. 22
Selecting various repeat functions ...................................................................... 23
Repeat play mode................................................................................................................................... 23
Repeating a section within a chapter/track.....................................................................................23
Angle .......................................................................................................................................................... 23
dvp3126-3727_94_eng.indd 6dvp3126-3727_94_eng.indd 6 2007-09-04 2:28:46 PM2007-09-04 2:28:46 PM

English
7
Contents
Viewing the disc playback information ...............................................................24
Title/Chapter/Track selection ............................................................................................................ 24
Time Search ............................................................................................................................................. 24
Special DVD Features ................................................................................................... 25
Playing a Title........................................................................................................................................... 25
Changing the Audio Language............................................................................................................. 25
Subtitles..................................................................................................................................................... 25
Special VCD and SVCD Feature.................................................................................. 25
Playback Control (PBC)........................................................................................................................ 25
Playing MP3/WMA/JPEG/Kodak/Fuji Picture CD................................................26-27
General Operation ................................................................................................................................ 26
Playback selection .................................................................................................................................. 26
Zoom picture (JPEG) ............................................................................................................................ 27
Playback with multi-angles (JPEG) ..................................................................................................... 27
DVD Menu Options
Using the Language setup menu ................................................................................. 28
OSD Language......................................................................................................................................... 28
Subtitle / Audio / DVD Menu.............................................................................................................. 28
Using the Video setup menu ................................................................................... 29-31
Setting the Aspect Ratio ...................................................................................................................... 29
View Mode ............................................................................................................................................... 30
TV System ................................................................................................................................................ 30
Video Out................................................................................................................................................. 30
Smart Picture........................................................................................................................................... 31
Using the Audio setup menu...................................................................................32-34
Front / Center / Surround Speakers................................................................................................. 32
Subwoofer ................................................................................................................................................ 33
Digital Output ......................................................................................................................................... 33
Night Mode .............................................................................................................................................. 34
Down Sampling ....................................................................................................................................... 34
Using the Rating setup menu..................................................................................35-36
Rating level settings .........................................................................................................................35-36
Changing the Password......................................................................................................................... 36
Using the Misc (Miscellaneous) setup menu ......................................................... 37-38
Restoring to the original settings....................................................................................................... 37
Volume Control...................................................................................................................................... 38
Speakers Delay........................................................................................................................................ 38
Others
Software upgrade .......................................................................................................... 39
Troubleshooting.......................................................................................................40~41
Specications ................................................................................................................. 42
Glossary........................................................................................................................... 43
dvp3126-3727_94_eng.indd 7dvp3126-3727_94_eng.indd 7 2007-09-04 2:28:46 PM2007-09-04 2:28:46 PM

English
8
Care and Safety Information
DANGER!
High voltage! Do not open the
device. You run the risk of getting
an electric shock.
The machine does not contain any
user-serviceable parts. Please leave
all maintenance work to qualied
personnel.
Setup
Finding a suitable location
– Place the set on a at, hard and stable
surface. Do not place the set on a
carpet.
– Do not put any equipment or heavy
objects on top of the set.
– Do not position the set on top of
other equipment that might heat it up
(such as receiver or amplier).
– Do not put anything under the set
(such as CDs, magazines).
– Install this unit near the AC outlet and
where the AC power plug can be
reached easily.
Space for ventilation
– Place the apparatus in a location with
adequate ventilation to prevent
internal heat build up. Allow at least
10 cm (4.0”) clearance from the rear
and the top of the set and 5cm (2.0”)
from the left and right to prevent
overheating.
10cm (4.0") 10cm (4.0")
5cm (2.0")
5cm (2.0")
Avoid high temperatures, moisture,
water and dust
– Apparatus shall not be exposed to
dripping or splashing.
– Do not place any sources of danger
on the apparatus (such as liquid lled
objects, lighted candles).
Cleaning discs
Some problems occur because the disc
inside the player is dirty (frozen picture,
sound disruptions, picture distortions).
To avoid these problems, discs should be
cleaned on a regular basis.
To clean a disc, use a micro bre cleaning
cloth and wipe the disc from the center
to the edge in a straight line.
CAUTION!
Do not use solvents such as benzene,
thinner, commercially available cleaners,
or anti-static sprays intended for analog
discs. Since the optical unit (laser) of the
DVD player operates at a higher power
than regular DVD or CD players,
cleaning CDs intended for DVD or CD
players may damage the optical unit
(laser). Therefore, refrain from using a
cleaning CD.
dvp3126-3727_94_eng.indd 8dvp3126-3727_94_eng.indd 8 2007-09-04 2:28:47 PM2007-09-04 2:28:47 PM

English
9
General Information
Accessories supplied
Region
U.S.A. and
Canada regions
U.K and
Europe regions
Asia Pacic,
Taiwan, Korea
Australia,
New Zealand,
Latin America
Russia and
India regions
China, Calcos Islands,
Walls and Futuna
Islands
Discs that can
be played
Remote
control and
two AAA
batteries
Region codes
This DVD player is designed to support
the Region Management System. Check
the regional code number on the disc
package. If the number does not match
the player’s region number (see table
below), the player may be unable to
playback the disc.
Tips:
– It may not be possible to play CD-R/RW
or DVD-R/RW in all cases due to the type of
disc or condition of the recording.
– If you are having trouble playing a certain
disc, remove the disc and try a different one.
Improper formatted disc will not played on
this DVD player.
Composite
video cable
(yellow) and
Audio cables
(white, red)
SUBTITLE
ZOOM
AUDIO
STOP
PLAY/PAUSE
MUTE
SETUP
TITLE
RETURN
MENU
DISC
DISPLAY
NEXT
PREV
dvp3126-3727_94_eng.indd 9dvp3126-3727_94_eng.indd 9 2007-09-04 2:28:47 PM2007-09-04 2:28:47 PM

English
10
IMPORTANT!
– The progressive scan video quality
is only possible when using YPbPr
and a progressive scan television is
required.
Using Component Video jacks
(YPbPr)
AUse the component video cables (red/
blue/green) to connect the DVD player’s
YPbPr jacks to the component video
input jacks (or labeled as YPbPr) on the
television (cable not supplied).
BTo hear sound of this DVD player
through your television, use the audio
cables (white/red) to connect
FRONT (L/R) AUDIO OUT jacks of the
DVD player to the corresponding
AUDIO IN jacks on the television (cable
supplied).
CProceed to page 17 for detailed
progressive scan setup.
Connections
TIPS: Before making or changing any connections, make sure that all the devices are disconnected
from the power outlet.
Connecting to television
IMPORTANT!
– You only need to make one video
connection from the following
options, depending on the
capabilities of your television.
– Connect the DVD player directly
to the television.
Using Composite Video jacks
(CVBS)
AUse the composite video cable (yellow)
to connect the DVD player’s TV OUT
(CVBS) jack to the video input jack (or
labeled as A/V In, Video In, Composite or
Baseband) on the television (cable
supplied).
BTo hear sound of this DVD player
through your television, use the audio
cables (white/red) to connect
FRONT (L/R) AUDIO OUT jacks of the
DVD player to the corresponding
AUDIO IN jacks on the television (cable
supplied).
DIGITAL
OUT TV OUT
COAXIAL
AUDIO OUT COMPONENT VIDEO OUT
FRONT R
FRONT L
REAR R
REAR L
SUBWOOFER
CENTER
AUDIO
IN
V (Pr/Cr)
U (Pb/Cb)
Y
S-VIDEO
IN
VIDEO IN
COMPONENT
VIDEO IN
AUDIO
OUT
V(Pr/Cr)
U(Pb/Cb)
Y
S-VIDEO
IN
VIDEOIN
COMPONENT
VIDEOIN
21
DIGITAL
OUT TV OUT
COAXIAL
AUDIO OUT COMPONENT VIDEO OUT
FRONT R
FRONT L
REAR R
REAR L
SUBWOOFER
CENTER
AUDIO
IN
V (Pr/Cr)
U (Pb/Cb)
Y
S-VIDEO
IN
VIDEO IN
COMPONENT
VIDEO IN
AUDIO
OUT
V(Pr/Cr)
U(Pb/Cb)
Y
S-VIDEO
IN
VIDEOIN
COMPONENT
VIDEOIN
2
1
dvp3126-3727_94_eng.indd 10dvp3126-3727_94_eng.indd 10 2007-09-04 2:28:51 PM2007-09-04 2:28:51 PM

English
11
DIGITAL
OUT TV OUT
COAXIAL
O
OUT COMPONENT VIDEO OUT
FRONT R
FRONT L
R
R
R
L
AUDIO IN
R L
VIDEO
IN
TO TVANT IN
CH3 CH4
ANT IN
ANTIN
1
3
4
2
Connections (continued)
TIPS: Before making or changing any connections, make sure that all the devices are disconnected
from the power outlet.
IMPORTANT!
– If your television only has a single
Antenna In jack (or labeled as 75
ohm or RF In,) you will need an RF
modulator in order to view the
DVD playback on the television. See
your electronics retailer or contact
Philips for details on RF modulator
availability and operations.
Using an accessory RF modulator
AUse the composite video cable (yellow)
to connect the DVD player’s TV OUT
(CVBS) jack to the video input jack on
the RF modulator.
BUse the RF coaxial cable (not supplied) to
connect ANTENNA OUT or TO TV jack
on the RF modulator to the ANTENNA
IN jack on the television.
RF coaxial cable to TV
Back of RF Modulator
(example only)
CTo hear sound of this DVD player
through your TV, use the audio cables
(white/red) to connect FRONT (L/R)
AUDIO OUT jacks of the DVD player to
the corresponding AUDIO IN jacks on
the RF modulator (cable supplied).
DConnect the Antenna or Cable TV
service signal to the ANTENNA IN or
RF IN jack on the RF modulator. (It may
have been connected to your TV
previously. Disconnect it from the TV).
dvp3126-3727_94_eng.indd 11dvp3126-3727_94_eng.indd 11 2007-09-04 2:28:51 PM2007-09-04 2:28:51 PM

English
12
Connections (continued)
TIPS: Before making or changing any connections, make sure that all the devices are disconnected
from the power outlet.
Connecting the power cord
After everything is connected
properly, plug in the AC power cord
to the power outlet.
Never make or change any connections
with the power switched on.
When no disc is loaded, press
STANDBY ON on the DVD player
front panel.
“– – –” may appear on the display
panel.
Connecting to a Multi
Channel Receiver
Receiver has a Dolby Digital
decoder
ASelect one of the video connections
(CVBS VIDEO IN or COMPONENT
VIDEO IN) depending on the options
available on your television.
BConnect the Audio Out Left and Right
jack for Front and Rear speakers to the
corresponding input jacks on your
receiver (cable not supplied).
CConnect the Audio Out for Center
speaker and Subwoofer to the
corresponding inputs on your receiver
(cable not supplied).
DIGITAL
OUT TV OUT
COAXIAL
AUDIO OUT COMPON
E
FRONT R
FRONT L
REAR R
REAR L
SUBWOOFER
CENTER DIGITAL
OUT TV OUT
COAXIAL
AUDIO OUT COMPONENT VIDEO OUT
FRONT R
FRONT L
REAR R
REAR L
SUBWOOFER
CENTER
MULTICHANNEL AUDIO IN
FRONTREAR
CENTER
FRONTREAR
SUBW.
dvp3126-3727_94_eng.indd 12dvp3126-3727_94_eng.indd 12 2007-09-04 2:28:51 PM2007-09-04 2:28:51 PM

English
13
Connecting to a stereo
system
Receiver has a PCM, Dolby Digital
or MPEG decoder
ASelect one of the video connections
(CVBS VIDEO IN or COMPONENT
VIDEO IN) depending on the options
available on your television.
BConnect the COAXIAL jack of the DVD
player to the corresponding Digital Audio
In jack on your receiver (cable not
supplied).
CSet the DVD player’s digital output to
PCM-Only or ALL depending on the
capabilities of your receiver (see page 33
{Digital Output}).
Tip:
– If the audio format of the Digital Output
does not match the capabilities of your
receiver, the receiver will produce a strong,
distorted sound or no sound at all.
Stereo system has right/ left Audio
In jacks
ASelect one of the video connections
(CVBS VIDEO IN or COMPONENT
VIDEO IN) depending on the options
available on your television.
BUse the audio cables (white/red) to
connect FRONT (L/R) AUDIO OUT
jacks of the DVD Player to the
corresponding AUDIO IN jacks on the
stereo system (cable supplied).
Connecting to a digital AV
receiver
Optional connections
TIPS: Before making or changing any connections, make sure that all the devices are disconnected
from the power outlet.
DIGITAL
OUT TV OUT
COAXIAL
AUDIO OUT COMPONENT VIDEO OUT
FRONT R
FRONT L
REAR R
REAR L
SUBWOOFER
CENTER
AUDIO
IN
STEREO
DIGITAL
DIGITAL
OUT TV OUT
COAXIAL
AUDIO OUT COMPONENT VIDEO OUT
FRONT R
FRONT L
REAR R
REAR L
SUBWOOFER
CENTER
AUDIO
IN
DIGITAL
AV Receiver
dvp3126-3727_94_eng.indd 13dvp3126-3727_94_eng.indd 13 2007-09-04 2:28:52 PM2007-09-04 2:28:52 PM

English
14
Product Overview
Front and Rear Panels
STANDBY ON 2
– Turns on the player or switches
to standby mode
Disc Tray
OPEN/CLOSE ç
– Opens or closes the disc tray.
Display panel
– Shows information about the
current status of the DVD player.
STOP
– Stops playback
PLAY/PAUSE u
– Starts or pauses playback.
IR Sensor
– Point the remote control towards
this sensor
DIGITAL
OUT TV OUT
COAXIAL
AUDIO OUT COMPONENT VIDEO OUT
FRONT R
FRONT L
REAR R
REAR L
SUBWOOFER
CENTER
Mains ~(AC Power Cord)
– Connect to a standard AC outlet
Multi-channel Audio Out
– Center speaker, subwoofer, front
and rear speakers multi-channel
connection
COAXIAL (Digital audio out)
– Connect to coaxial AUDIO input
of a digital audio equipment
YPbPr (Component Video Out)
– Connect to YPbPr input of a
television
TV OUT (CVBS)
– Connect to CVBS Video input of a
television
dvp3126-3727_94_eng.indd 14dvp3126-3727_94_eng.indd 14 2007-09-04 2:28:52 PM2007-09-04 2:28:52 PM

English
15
SUBTITLE
ZOOM
AUDIO
STOP
PLAY/PAUSE
MUTE
SETUP
TITLE
RETURN
MENU
DISC
DISPLAY
NEXT
PREV
Product Overview (continued)
Remote Control
DISC MENU
– Enters or exits the disc
contents menu
– Switches on or off the
playback control mode (for
VCD 2.0 only)
OK
– Conrms an entry or
selection
RETURN/TITLE
– To go back to previous
menu/ show title menu
PREV í
– Skips to the previous title/
chapter/track
STOP
– Stops playback
uPLAY/PAUSE
– Starts or pauses playback
SUBTITLE
– To access subtitle language
system menu
ZOOM
– Enlarge a picture on the TV
screen
VOLUME
– Displays the speaker’s
volume level
REPEAT/ REPEAT A-B
– Selects various repeat mode
– Repeats playback a specic
section on a disc
2
– To switch the DVD player
to standby mode or ON
DISPLAY
– Displays information on TV
screen during playback
WX
– Cursor buttons for moving
to the left or right, do a fast
forward/reverse search.
ST
– Cursor buttons for moving
up/down, do a slow
forward/backward
SETUP
– Enters or exits the system
setup menu
NEXT ë
– Skips to the next title/
chapter/track
MUTE
– Disables or enables sound
output
Alphanumeric keypad
– Selects numbered items in
a menu
AUDIO
– Selects an audio language
(DVD/VCD) or an audio
channel
dvp3126-3727_94_eng.indd 15dvp3126-3727_94_eng.indd 15 2007-09-04 2:28:53 PM2007-09-04 2:28:53 PM

English
16
Step 1: Inserting Batteries
AOpen the battery compartment.
BInsert two batteries type R03 or AAA,
following the indications (+ –) inside the
compartment.
CClose the cover.
CAUTION!
– Remove batteries if they are
exhausted or if the remote is not to
be used for a long time.
– Do not use old and new or
different types of batteries in
combination.
– Batteries contain chemical
substances, so they should be
disposed of properly.
Using the remote control to
operate the system
STOP
PLAY/PAUSE
MUTE
SETUP
TITLE
RETURN
MENU
DISC
DISPLAY
NEXT
PREV
AAim the remote control directly at the
remote sensor (IR) on the front panel.
BDo not put any objects between the
remote control and the DVD player
while operating the DVD player.
Step 2: Finding your viewing
channel
APress STANDBY-ON 2on the DVD
player to turn it on.
BTurn on the TV and set it to the correct
video-in channel. You should see the blue
DVD background screen.
Usually these channel are between the
lowest and highest channels and may
be called FRONT, A/V IN, VIDEO.
See your TV’s manual for more
details.
Or, you may go to channel 1 on your
TV, then press the Channel down
button repeatedly until you see the
Video In channel.
Or, the TV remote control may have
a button or turn that chooses
different video modes.
Or, set the TV to channel 3 or 4 if
you are using an RF modulator.
CIf you are using external equipment, (such
as audio system or receiver), turn it on
and select the appropriate input source
for the DVD player output. Refer to the
equipment user’s manual for detail.
Getting Started
dvp3126-3727_94_eng.indd 16dvp3126-3727_94_eng.indd 16 2007-09-04 2:28:53 PM2007-09-04 2:28:53 PM

English
17
Getting Started (continued)
Step 3: Setting up
Progressive Scan
feature
(for Progressive Scan TV only)
The progressive scan displays twice the
number of frames per seconds than
interlaced scanning (ordinary normal TV
system). With nearly double the number
of lines, progressive scan offers higher
picture resolution and quality.
Before you start...
– Ensure that you have connected this
DVD player to a progressive scan TV
using the Y Pb Pr connection (see page
10).
– Ensure that you have completed the
basic installation and set-up.
ATurn on your TV and set to interlace
mode (refer to your TV user manual).
BPress STANDBY ON 2on the
remote control to turn on the DVD
player.
CSelect the correct video-in channel.
 The DVD background menu appears.
DPress SETUP.
EPress STto select { Video }, then
press X.
Language
Video
Audio
Misc
Rating
Aspect Ratio :
View Mode :
TV System :
Video Out :
Smart Picture :
4:3
Auto Fit
NTSC
Component
Personal
Language
Video
Audio
Misc
Rating
Aspect Ratio :
View Mode :
TV System :
Video Out :
Smart Picture :
4:3
Auto Fit
NTSC
Component
Personal
Language
Video
Audio
Misc
Rating
Aspect Ratio :
View Mode :
TV System :
Video Out Interlaced
Smart Picture
P-Scan
4:3
Auto Fit
PAL
FPress STrepeatedly to select
{ Video Out }, then press X.
GSelect { P-Scan }, then press OK to
conrm.
 The menu will appear on the TV.
Activating Progressive Scan
1.Ensure your TV system supports
Progressive Mode
2.If there is a distorted picture on
the TV, wait 15 seconds for
automatic recover
Yes NO
HPress Wto highlight { Yes } and press
OK to conrm.
ITurn on your TV progressive scan mode
(refer to your TV user manual).
 The menu will appear on the TV.
Confirm again to use new setting
Revert to original setting in 14 seconds
Yes NO
JPress Wto highlight { Yes } and press
OK to conrm.
 The setup is now completed and you
can start enjoy the high quality
picture.
To deactivate Progressive Scan
manually:
 Wait for 15 seconds for the auto
recovery.
OR
APress OPEN/CLOSE çon the DVD
player to open the disc tray.
BPress numeric keypad ‘1’ on the
remote control for few seconds.
 The DVD background screen appears.
Tip:
– There are some progressive scan TVs and
High-Denition TVs that are not fully
compatible with this unit, resulting in the
unnatural picture when playing back a DVD
VIDEO disc in the progressive scan mode. In
such a case, turn off the progressive scan
feature on both the DVD player and your TV.
TIPS: The underlined option is the factory default setting.
Press Wto go back to previous menu item. Press SETUP to exit the menu item.
dvp3126-3727_94_eng.indd 17dvp3126-3727_94_eng.indd 17 2007-09-04 2:28:54 PM2007-09-04 2:28:54 PM

English
18
Getting Started (continued)
TIPS: The underlined option is the factory default setting.
Press Wto go back to previous menu item. Press SETUP to exit the menu item.
Step 4: Selecting the
matching color
system
The color system of the DVD player, disc
and TV should match in order for the
disc to play. Before changing the TV
system, determine the color system of
your TV.
Language
Video
Audio
Misc
Rating
Aspect Ratio
View Mode :
TV System :
Video Out :
Smart Picture :
4:3
Auto Fit
NTSC
Component
Personal
Language
Video
Audio
Misc
Rating
Language
Video
Audio
Misc
Rating
Aspect Ratio :
View Mode :
TV System NTSC
Video Out PAL
Smart Picture Multi
4:3
Auto Fit
APress SETUP.
BPress STto select { Video }, then
press X.
CPress STrepeatedly to select
{ TV System }, then press X.
DUse STto select one of the options
below:
{ PAL }
Select this if the connected TV has the
PAL colour system. It will change the
video signal of an NTSC disc and output
it to PAL format.
{ NTSC }
Select this if the connected TV has the
NTSC colour system. It will change the
video signal of a PAL disc and output it to
NTSC format.
{ Multi }
Select this if the connected TV is
compatible with both NTSC and PAL
(multi-system). The output format will be
in accordance with the video signal of the
disc.
ESelect a setting and press OK.
 Follow the instructions show on the
TV to conrm the selection (if any).
Confirm again to use new setting
Revert to original setting in 14 seconds
Yes NO
Changing NTSC to PAL
1.Ensure your TV system supports
PAL Standard
2.If there is a distorted picture on
the TV, wait 15 seconds for
automatic recover
Yes NO
FPress Wto highlight { Yes } and press
OK to conrm.
To reset to default TV color system:
 Wait for 15 seconds for the auto
recovery.
OR
APress OPEN/CLOSE çon the DVD
player to open the disc tray.
BPress numeric keypad ‘3’ on the
remote control for few seconds.
 The DVD background menu appears.
Tips:
– Before changing the current TV colour
setting, ensure that your TV supports the
‘selected TV System’.
– If there is no proper picture on your TV,
wait for 15 seconds for auto recovery.
Select PAL for Asia Pacic region.
Select NTSC for Taiwan region.
dvp3126-3727_94_eng.indd 18dvp3126-3727_94_eng.indd 18 2007-09-04 2:28:54 PM2007-09-04 2:28:54 PM

English
19
Getting Started (continued)
Step 5: Setting the language
The language options are different
depending on your country or region. It
may not correspond to the illustrations
shown on the user manual.
On-screen display (OSD) language
Select this to change the language of this
DVD player screen display menu.
The menu language (on-screen display)
for the system will remain as you set it.
Language
Video
Audio
Rating
Misc
Audio : English
DVD menu : English
OSD language English
Subtitle Hindi
APress SETUP.
BPress STto select { Language }, then
press X.
CPress STto select { OSD Language },
then press X.
DUse STto select a language and press
OK to conrm.
TIPS: The underlined option is the factory default setting.
Press Wto go back to previous menu item. Press SETUP to exit the menu item.
Audio, Subtitle and DVD menu
languages
You can choose your preferred language
or sound track from audio, subtitles and
DVD menu languages. If the selected
language is not available on the disc, the
disc’s default language will be used
instead.
Language
Video
Audio
Rating
Misc
OSD language : English
Subtitle : Auto
DVD menu
Audio English
Hindi
APress SETUP.
BPress STto select { Language }, then
press X.
CPress STto highlight one of the
options below, then press X.
{ Audio }
Select this to change disc sound track
language.
{ Subtitle }
Select this to change the subtitle language.
{ DVD menu }
Select this to change the language of the
disc menu.
DUse STto select a language and press
OK to conrm.
ERepeat steps C- Dfor other language
settings.
dvp3126-3727_94_eng.indd 19dvp3126-3727_94_eng.indd 19 2007-09-04 2:28:55 PM2007-09-04 2:28:55 PM

English
20
IMPORTANT!
– If the INVALID KEY appears on
the TV screen when a button is
pressed, it means the function is not
available on the current disc or at
the current time.
– DVD discs and players are designed
with regional restrictions. Before
playing a disc, make sure the disc is
for the same zone as your player.
Playable discs
Using this DVD player, you can playback
on the following discs:
DVD Video
(Digital Versatile Disc)
DVD±RW (DVD Rewritable)
Audio/Video format or
MP3/WMA/JPEG les.
DVD±R (DVD Recordable)
Audio/Video format or
MP3/WMA/JPEG les.
CD-R (CD-Recordable)
Audio/Video format or
MP3/WMA/JPEG les.
CD-RW (CD-Rewritable)
Audio/Video format or
MP3/WMA/JPEG les.
Audio CD
(Compact Disc Digital Audio)
Video CD
(Formats 1.0, 1.1, 2.0)
Playback from Disc
TIPS: Some discs cannot be played on this DVD player due to the conguration and characteristics of
the disc, or due to the condition of recording and authoring software that was used.
Super Video CD
MP3-Disc
Supported formats
MP3/WMA tracks
– The le extensions has be to be
‘.mp3’, ‘.wma’
– JPEG/ISO format
– Maximum 15 characters display.
– Supported sampling frequencies and
corresponding bit-rates;
32kHz 64 – 320 kbps
44.1kHz, 48kHz 80 – 320 kbps
JPEG pictures
– The le extensions has be to be ‘.JPG’
and not ‘.JPEG.’
– JPEG/ISO format
– It can only display DCF-standard still
pictures or JPEG pictures such as
TIFF.
Tips:
– Maximum 100 sessions for CD and 10
multi border for DVD are supported.
– For DVD-R and DVD-RW multi border,
only nalized disc are supported.
– For DVD+R and DVD+RW multi border
both nalized and unnalized disc are NOT
supported.
dvp3126-3727_94_eng.indd 20dvp3126-3727_94_eng.indd 20 2007-09-04 2:28:55 PM2007-09-04 2:28:55 PM