Philips HTP3350K/55 User manual

TABLE OF CONTENTS
Page
Version 1.3
Service Manual
. Technical Specifications…………....………………………..............1-2
. Safety Instruction, Warning & Notes….……………………....….....1-3
. Mechanical and Dismantling Instructions…………........................3-1
. Software Version & Upgrades, Region Code Change..……..........4-1
. Trouble Shooting Chart……………………………………………….5-1
. Wiring Diagram………………………………………..………..….….6-1
. Electrical Diagrams and Print-layouts..….…………………....….…7-1
. Set Mechanical Exploded view & Part list.…………………..….….8-1
©Copyright 2009 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
All rights reserved. No part of this publication may be reproduced, stored in aretrieval system or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise
without the prior permission of Philips.
CLASS 1
LASER PRODUCT
PHILIPS
GB
Published by SL - 940 BU AVM Printed in The Netherlands Subject to modification
. DFU Instruction..............................................................................2-1
. Revision List..................................................................................9-1
3139 785 34793
DVP3350K/55
HTP3350K/55
DVP3354K/55
DVP/HTP3350K DVP3354K/55

6SHFLÀFDWLRQ
Note
6SHFLÀFDWLRQDQGGHVLJQDUHVXEMHFWWRFKDQJH

without notice.
Accessories supplied
Remote control and batteries
Audio/video cables
Power cable
Playback media
DVD-Video, Video CD/SVCD, Audio CD, CD-R/
CD-RW, DVD+R/+RW, DVD-R/-RW, DivX-CD,
3LFWXUH&'03&':0$&'86%ÁDVKGULYH
USB
Compatibility: Hi-Speed USB (2.0)
Class support: UMS (USB Mass Storage Class)
TV standard
Number of lines:
625 (PAL/50Hz); 525 (NTSC/60Hz)
Playback: Multi-standard (PAL/NTSC)
Video performance
Video DAC: 12 bits, 108 MHz
Y Pb Pr: 0.7 Vpp ~ 75 ohm
Video output: 1 Vpp ~ 75 ohm
Video format
Digital compression:
MPEG 2: DVD/SVCD
MPEG 1: VCD/DivX
Horizontal resolution:
DVD: 720 pixels (50 Hz); 720 pixels (60 Hz)
VCD: 352 pixels (50 Hz); 352 pixels (60 Hz)
Vertical resolution:
DVD: 576 lines (50 Hz); 480 lines (60 Hz)
VCD: 288 lines (50 Hz); 240 lines (60 Hz)
Audio performance
DA converter: 24 bits, 192 kHz
Frequency response:
DVD: 4 Hz - 22 kHz (48 kHz);
4 Hz - 44 kHz (96 kHz)
SVCD: 4 Hz - 20 kHz (44.1 kHz);
4 Hz - 22 kHz (48 kHz)
CD/VCD: 4 Hz - 20 kHz (44.1 kHz)
Signal-Noise (1 kHz): > 90 dB
Dynamic range (1 kHz): > 80 dB
Crosstalk (1 kHz): > 70 dB
Distortion/noise (1 kHz): > 65 dB
MPEG MP3: MPEG Audio L3
Audio format
Digital:
MPEG/AC-3/PCM: Compressed digital (16, 20, 24
bits fs, 44.1, 48, 96 kHz)
MP3 (ISO 9660): 96, 112, 128, 256 kbps &
variable bit rate fs, 32, 44.1, 48 kHz
Analog sound stereo
Dolby surround compatible downmix from Dolby
Digital multi-channel sound
Connections
Y Pb Pr output: Cinch 3x
Video output: Cinch (yellow)
Audio output (L+R): Cinch (white/red)
Digital output:
1 coaxial: IEC60958 for CDDA/LPCM;
IEC61937 for MPEG 1/2, Dolby Digital
Main unit
Dimensions (w x h x d): 360 x 38 x 203 (mm)
Net Weight: approximately 1.3 kg
Power
Power supply rating: 110 V - 240V; 50/60 Hz
Power consumption: < 10 W
Power consumption in standby mode: < 1 W
/DVHU6SHFLÀFDWLRQ
Type: Semiconductor laser InGaAIP (DVD), AIGaAs
(CD)
Wave length: 658 nm (DVD), 790 nm (CD)
Output Power: 7.0 mW (DVD), 10.0 mW (VCD/CD)
Beam divergence: 60 degrees
1-2

Safety instruction
1. General safety
Safety regulations require that during a repair:
. Connect the unit to the mains via an isolation transformer.
. Replace safety components indicated by the symbol ,
only by components identical to the original ones. Any
other component substitution (other than original type)
may increase risk of fire or electrical shock hazard.
Safety regulations require that after a repair, you must
return the unit in its original condition. Pay, in particular,
attention to the following points:
. Route the wires/cables correctly, and fix them with the
mounted cable clamps.
. Check the insulation of the mains lead for external
damage.
. Check the electrical DC resistance between the mains
plug and the secondary side:
1) Unplug the mains cord, and connect a wire between
the two pins of the mains plug.
2) Set the mains switch the “on” position (keep the
mains cord unplug).
3) Measure the resistance value between the mains
plug and the front panel, controls, and chassis
bottom.
4) Repair or correct unit when the resistance
measurement is less than 1M
¡
.
5) Verify this, before you return the unit to the
customer/user (ref. UL-standard no. 1492).
6) Switch the unit “off”, and remove the wire between
the two pins of the mains plug.
2.Laser safety
This unit employs a laser. Only qualified service personnel
may remove the cover, or attempt to service this device
(due to possible eye injury).
Laser device unit
Type :SemiconductorlaserGaAlAs
Wavelength : 650nm (DVD)
: 780nm (VCD/CD)
Output power : 7mW (DVD)
:10mW(DVD/CD)
Beam divergence: 60 degree
Note: Use of controls or adjustments or performance of
procedure other than those specified herein, may result in
hazardous radiation exposure. Avoid direct exposure to
beam.
Safet
y
instruction, Warnin
g
& Notes
1-3

Warning
1.General
. All ICs and many other semiconductors are susceptible to
electrostatic discharges (ESD). Careless handing during
repair can reduce life drastically. Make sure that, during
repair, you are at the same potential as the mass of the
set by a wristband with resistance. Keep components and
tools at this same potential. Available ESD protection
equipment:
1) Complete kit ESD3 (small tablemat, wristband,
connection box, extension cable and earth cable)
4822 310 10671.
2) Wristband tester 4822 344 13999.
. Be careful during measurements in the live voltage
section. The primary side of the power supply , including
the heat sink, carries live mains voltage when you
connect the player to the mains (even when the player is
“off”!). It is possible to touch copper tracks and/or
components in this unshielded primary area, when you
service the player. Service personnel must take
precautions to prevent touching this area or components
in this area. A “lighting stroke” and a stripe-marked
printing on the printed wiring board, indicate the primary
side of the power supply.
. Never replace modules, or components, while the unit is
“on”.
2. Laser
. The use of optical instruments with this product, will
increase eye hazard.
. Only qualified service personnel may remove the cover
or attempt to service this device, due to possible eye
injury.
. Repair handing should take place as much as possible
with a disc loaded inside the player.
. Text below is placed inside the unit, on the laser cover
shield:
Notes: Manufactured under licence from Dolby
Laboratories. The double-D symbol is trademarks of Dolby
Laboratories, Inc. All rights reserved.
CAUTION: VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN, AVOID EXPOSURE
TO BEAM.
1-4

Lead-Free requirement for service
INDENTIFICATION:
Regardless of special logo (not always indicated)
One must treat all sets from 1.1.2005 onwards, according
next rules.
Important note: In fact also products a little older can also
be treated in this way as long as you avoid mixing
solder-alloys (leaded/ lead-free). So best to always use
SAC305 and the higher temperatures belong to this.
Due to lead-free technology some rules have to be
respected by the workshop during a repair:
xUse only lead-free solder alloy Philips SAC305 with
order code 0622 149 00106. If lead-free solder-paste is
required, please contact the manufacturer of your
solder-equipment. In general use of solder-paste within
workshops should be avoided because paste is not easy
to store and to handle.
xUse only adequate solder tools applicable for lead-free
solder alloy. The solder tool must be able
oTo reach at least a solder-temperature of 400°C,
oTo stabilize the adjusted temperature at the
solder-tip
oTo exchange solder-tips for different applications.
xAdjust your solder tool so that a temperature around
360°C – 380°C is reached and stabilized at the solder
joint. Heating-time of the solder-joint should not exceed
~ 4 sec. Avoid temperatures above 400°C otherwise
wear-out of tips will rise drastically and flux-fluid will be
destroyed. To avoid wear-out of tips switch off un-used
equipment, or reduce heat.
xMix of lead-free solder alloy / parts with leaded solder
alloy / parts is possible but PHILIPS recommends
strongly to avoid mixed
solder alloy types (leaded and lead-free). If one cannot
avoid, clean carefully the
solder-joint from old solder alloy and re-solder with new
solder alloy (SAC305).
xUse only original spare-parts listed in the
Service-Manuals. Not listed standard-material
(commodities) has to be purchased at external
companies.
xSpecial information for BGA-ICs:
- always use the 12nc-recognizable soldering
temperature profile of the specific BGA (for
de-soldering always use highest lead-free
temperature profile, in case of doubt)
- lead free BGA-ICs will be delivered in so-called
‘dry-packaging’ (sealed pack including a silica gel
pack) to protect the IC against moisture. After
opening, dependent of MSL-level seen on
indicator-label in the bag, the BGA-IC possibly
still has to be baked dry. This will be
communicated via AYS-website.
Do not re-use BGAs at all.
xFor sets produced before 1.1.2005, containing
leaded soldering-tin and components, all needed
spare-parts will be available till the end of the
service-period. For repair of such sets nothing
changes.
xOn our website:
www.atyourservice.ce.Philips.com
You find more information to:
BGA-de-/soldering (+ baking instructions)
Heating-profiles of BGAs and other ICs used in
Philips-sets
You will find this and more technical information
within the “magazine”, chapter “workshop news”.
For additional questions please contact your local
repair-helpdesk.
Notes
1-5

Descripción general del
producto
Unidad principal
a2(Modo de espera encendido)
Enciende el reproductor de DVD o•
pasa al modo de espera.
bBandeja de discos
cPanel de visualización
dZ (Abrir/Cerrar)
Abre o cierra la bandeja de discos.•
eu(Reproducir/Pausa)
Inicia, hace una pausa o reanuda la•
reproducción del disco.
fToma (USB)
Conecta una unidad USB Flash.•
gMIC
Entrada de audio desde un micrófono.•
4
31 2 6
57
Remote control
4
3
6
7
9
8
1
5
2
16
17
12
15
13
14
10
11
18
a2(Modo de espera encendido)
Enciende el reproductor de DVD o•
pasa al modo de espera.
bZ (Abrir/Cerrar)
Abre o cierra la bandeja de discos.•
cDISC MENU
Accede o sale del menú del disco.•
Pasa al modo de disco.•
Para VCD y SVCD, activa o desactiva el•
modo PBC (control de reproducción).
2-1

dv V b B (Botones de navegación)
Para navegar por los menús.•
Avanza (• B) o retrocede (b)
rápidamente. Púlselos varias veces para
incrementar la velocidad de búsqueda.
Avanza (• v) o retrocede (V)
rápidamente. Púlselos varias veces para
incrementar la velocidad de búsqueda.
e2BACK
Regresa al menú de pantalla anterior.•
En discos DVD, se desplaza hacia el•
menú de títulos.
Para la versión 2.0 de VCD o SVCD•
con PBC encendido, regresa al menú.
fí/ë(Anterior/Siguiente)
Pasa al título, capítulo o pista anterior o•
siguiente.
Manténgalos presionados para avanzar•
o retroceder rápidamente..
g(USB)
Cambia al modo USB y muestra el•
contenido del dispositivo.
hBotones numéricos
Selecciona un elemento para•
reproducirlo.
iSUBTITLE
Selecciona el idioma de subtítulos para•
DVD o DivX.
Accede al menú para copiar o eliminar•
información del USB.
j,ZOOM
Ajusta el formato de la imagen a la•
pantalla del televisor.
Acerca o aleja la imagen.•
kVOCAL
Cambia el canal de audio de un disco•
de karaoke.
lKARAOKE
Accede o sale del menú de karaoke.•
mAUDIO/CREATE MP3
Selecciona un idioma o canal de audio.•
Accede al menú para crear archivos•
MP3.
nx(Detener)
Detiene la reproducción del disco.•
ou(Reproducir/Pausa)
Inicia, hace una pausa o reanuda la•
reproducción del disco.
pINFO
En un disco, muestra el estado actual o•
la información del disco.
Para secuencias de diapositivas, muestra•
una vista en miniatura de los archivos
de fotos.
qOK
Confirme la entrada o selección.•
rSETUP
Accede o sale del menú de•
configuración.
2-2

Mechanical and Dismantling Instructions
Dismantling Instruction
The following guidelines show how to dismantle the player.
Step1: Remove 5 screws around the Top Cover, and then remove the Top Cover (Figure 1).
Figure 1
Step2: If it is necessary to dismantle Loader or Front Panel, the Front door should be removed first. (Figure 2)
Note: Make sure to operate gently otherwise the guider would be damaged.
Figure 2
3-1
Please kindly note that dismantle the front door
assembly carefully to avoid damage tray and the front door.

Mechanical and Dismantling Instructions
Dismantling Instruction
Step3: If the tray can’t open in normal way, you can make it through the instruction as below (Figure 3).
Note: Make sure to operate gently otherwise the guider would be damaged.
Figure 3
Step4: Dismantling Front Panel, disconnect the connectors (XP5, XP6. XP7), need release 4 snaps of Front Panel
and 2 snaps of bottom cabinet , then gently pull the Panel out from the set. (Figure 4 - Figure 6)
Figure 4
3-2
XP2
XP4
XP3
XP5
XP7
XP6
XP1
SNAP
SNAP
SNAP
SNAP
SNAP

3-3
Mechanical and Dismantling Instructions
Dismantling Instruction
Figure 5
Step5: Dismantling Loader, disconnect the 3 connectors (XP2, XP3, XP4) aiming in the below figure, and remove 1 screw that
connects the loader and the bottom cabinet. (Figure 5 & 6)
Figure 6