Philips AT921 User manual

AT940, AT921, AT893, AT890, AT753,
AT752, AT750
Register your product and get support at
Enregistrez votre produit et bénéficiez d’une assistance à l’adresse suivante
www.philips.com/welcome

1

AT940,AT921,AT893,AT890,AT753,AT752,AT750
ENGLISH 6
FRANÇAIS (CANADA) 23

6
Introduction
Congratulations on your purchase and welcome
to Philips! To fully benefit from the support that
Philips offers, register your product at
www.philips.com/welcome.
Please read this user manual, as it contains
information about the wonderful features of this
shaver as well as some tips to make shaving easier
and more enjoyable.
General description (Fig. 1)
A Protection cap
B Shaving unit
C Shaving unit release button
D Shaver on/off button (AT893/AT890/AT753/
AT752/AT750)
E Charging light (AT893/AT890/AT753/AT752/
AT750)
F Charging stand (AT940/AT921 only)
G Trimmer (AT940/AT921/AT893/AT890 only)
H Trimmer release slide (AT940/AT921/AT893/
AT890 only)
I Shaver on/off button (AT940/AT921 only)
J Battery symbol and plug symbol (AT940/AT921
only)
K Adapter
L Cleaning brush
Not shown: Storage pouch (AT940/AT921/AT893/
AT890 only)
Note: You can nd the type number on the back of the
shaver.
ENGLISH

Important
Read this user manual carefully before you use the
appliance and the charging stand (AT940/AT921
only). Save it for future reference.
Danger
- Make sure the adapter does not get wet.
Warning
- The adapter contains a transformer. Do not cut
off the adapter to replace it with another plug, as
this causes a hazardous situation.
- This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
- Children should be supervised to ensure that they
do not play with the appliance.
- Always unplug the shaver before you clean it
under the tap.
Caution
- Never use water hotter than 80°C to rinse the
shaver.
- Be careful with hot water. Always check if the
water is not too hot, to prevent your hands from
getting burnt.
- Do not immerse the charging stand (AT940/
AT921 only) in water or any other liquid, nor rinse
it under the tap.
- The shaver and the charging stand (AT940/AT921
only) are not dishwasher-proof.
- Water may leak from the socket at the bottom
of the shaver when you rinse it.This is normal
and not dangerous because all electronics are
enclosed in a sealed power unit inside the shaver.
ENGLISH 7

- Do not use the shaver, adapter or charging
stand (AT940/AT921 only) if it is damaged, as
this may cause injury. Always replace a damaged
adapter or charging stand with one of the original
type.
- Charge and store the appliance at a temperature
between 10°C and 35°C.
- Always place and use the shaver and the charging
stand (AT940/AT921 only) on a surface that is
fluid-resistant.
- Only use the adapter and the charging
stand (AT940/AT921 only) supplied.
- Always put the protection cap on the shaver
to protect the shaving heads when you are
travelling.
- If the shaver is subjected to a major change
in temperature, pressure or humidity, let
it acclimatise for 30 minutes before you use it.
Compliance with standards
- This shaver complies with the internationally
approved safety regulations and can be safely used
in the bath or shower and cleaned under the tap.
- This Philips appliance complies with all standards
regarding electromagnetic fields (EMF). If handled
properly and according to the instructions in this
user manual, the appliances are safe to use based
on scientific evidence available today.
General
- The appliance is equipped with an automatic
voltage selector and is suitable for mains voltages
ranging from 100 to 240 volts.
- The adapter transforms 100-240 volts to a safe
low voltage of less than 24 volts.
ENGLISH8

Charging
Note: The shaver cannot be used directly from the
mains.
AT940/AT921/AT893/AT890 only: It takes approx. 1
hour to fully charge the shaver.
AT753/AT752/AT750: It takes approx. 8 hours to
fully charge the shaver.
When you charge the shaver for the first time
or after a long period of disuse, let it charge until
the white battery symbol lights up continuously
(AT940/AT921) or the charging light lights up green
continuously (AT893/AT890/AT753/AT752/AT750.
A fully charged shaver provides up to 21 (AT940/
AT921), 17 (AT893/AT890) or 14 (AT753/AT752/
AT750) cordless shaves.
The shaving time may be less than expected as
a result of your shaving behaviour, your cleaning
habits or your beard type.
Charge indications
Battery low
- AT940/AT921:When the battery is almost empty
(when there are only 5 or fewer shaving minutes
left), the orange plug symbol starts to flash.When
you switch off the shaver, the orange plug symbol
continues to flash for a few seconds.
- AT893/AT890/AT753/AT752/AT750:When the
battery is almost empty (when there are only
5 or fewer shaving minutes left), the charging
light starts to flash orange.When you switch off
the shaver, the charging light continues to flash
orange for a few seconds.
ENGLISH 9

Quick charging (AT940/AT921/AT893/AT890
only)
- AT940/AT921:When you start charging the
empty battery, both the white battery symbol and
the plug symbol flash. After approx. 3 minutes,
the orange plug symbol goes out, while the
battery symbol continues to flash.The shaver now
contains enough energy for a 5-minute shave.
- AT893/AT890:When you start charging the
empty battery, the charging light alternately flashes
orange and green. After approx. 3 minutes the
charging light continues to flash green.The shaver
now contains enough energy for a 5-minute shave.
Charging
- AT940/AT921:When the shaver is charging, the
white battery symbol flashes.
- AT893/AT890/AT753/AT752/AT750:When the
shaver is charging, the charging light flashes green.
Battery fully charged
- AT940/AT921:When the battery is fully charged,
the white battery symbol lights up continuously.
Note: After approx. 30 minutes, the battery symbol
goes out to save energy.
ENGLISH10

- AT893/AT890/AT753/AT752/AT750:When the
battery is fully charged, the charging light lights up
green continuously.
Note: After approx. 30 minutes, the charging light goes
out to save energy.
Charging with the adapter
1 Put the small plug in the shaver.
2 Put the adapter in the wall socket.
,The charging light shows the charging status of
the shaver (see section ‘Charge indications’ in
this chapter).
Charging in the charging stand (AT940/
AT921 only)
1 Put the small plug in the charging stand.
2 Put the adapter in the wall socket.
3 Place the shaver in the charging stand.
,The charging light shows the charging status of
the shaver (see section ‘Charge indications’ in
this chapter).
Using the shaver
Note: This shaver can be used in the bath or shower. It
can therefore not be used directly from the mains for
safety reasons.
ENGLISH 11

Shaving tips and tricks
- This shaver is suitable for both wet and dry use.
Use the shaver with shaving gel or foam for extra
skin comfort, or use the shaver dry for extra
convenience.
Note: We advise you to use the shaver with shaving gel
or foam when you use it for a wet shave. Do not use
thick shaving cream or shaving oil with this shaver.
- For optimal shaving results, make circular
movements during use.
- The shaver is waterproof and can be used in the
bath or shower.
- Your skin may need 2 or 3 weeks to get
accustomed to the Philips shaving system.
Wet shaving
1 Apply some water to your skin.
2 Apply shaving foam or shaving gel to your skin.
3 Rinse the shaving unit under the tap to ensure
that the shaving unit glides smoothly over your
skin.
4 Press the on/off button once to switch on the
shaver.
5 Move the shaving heads in circular movements
over your skin.
ENGLISH12

Note: Rinse the shaver under the tap regularly to
ensure that it continues to glide smoothly over your
skin.
6 After shaving, press the on/off button once to
switch off the shaver and dry your face.
7 Clean the shaver (see chapter ‘Cleaning and
maintenance’).
Note: Make sure you rinse all foam or shaving gel off
the shaver.
Dry shaving
1 Press the on/off button once to switch on the
shaver.
2 Move the shaving heads in circular movements
over your skin.
3 After shaving, press the on/off button once to
switch off the shaver.
4 Clean the shaver (see chapter ‘Cleaning and
maintenance’).
Trimming (AT940/AT921/AT893/AT890 only)
You can use the trimmer to groom your sideburns
and moustache.
1 Push the trimmer slide downwards to open
the trimmer.
2 Press the on/off button once to switch on the
shaver.
,You can now start trimming.
3 After trimming, press the on/off button once to
switch off the shaver.
ENGLISH 13

4 Clean the trimmer (see chapter ‘Cleaning and
maintenance’).
5 Close the trimmer (‘click’).
Cleaning and maintenance
Never use compressed air, scouring pads, abrasive
cleaning agents or aggressive liquids such as petrol
or acetone to clean the shaver and the charging
stand (AT940/AT921 only).
Always unplug the shaver before you clean it under
the tap.
- Clean the shaver after every shave for optimal
shaving performance.
- Regular cleaning guarantees better shaving
performance.
- For the best cleaning results, we advise you to use
the Philips Cleaning spray (HQ110).
- Be careful with hot water. Always check if the
water is not too hot, to prevent your hands from
getting burnt.
Note: Water may leak from the socket at the bottom
of the shaver when you rinse it. This is normal and not
dangerous because all electronics are enclosed in a
sealed power unit inside the shaver.
ENGLISH14

Cleaning the shaving unit under the tap
1 Switch off the shaver.
2 Press the release button to open the shaving
unit.
3 Rinse the shaving unit and hair chamber under
a hot tap for 30 seconds.
Be careful with hot water.Always check if the
water is not too hot, to prevent your hands from
getting burnt.
- Rinse the hair chamber and the inside of the
shaving unit.
- Rinse the outside of the shaving unit.
4 Close the shaving unit and shake off excess
water.
Be careful not to hit the shaving unit against
anything while shaking off excess water.
Never dry the shaving unit and the hair chamber
with a towel or tissue, as this may damage the
shaving unit.
5 Open the shaving unit again and leave it open
to let the shaver dry completely.
ENGLISH 15

Cleaning the shaving unit with the cleaning
brush
1 Switch off the shaver.
2 Press the release button to open the shaving
unit.
3 Pull the shaving unit off the shaver.
4 Turn the lock anticlockwise (1) and remove the
retaining frame (2).
5 Remove and clean one shaving head at a time.
Each shaving head consists of a cutter and a
guard.
Note: Do not clean more than one cutter and guard
at a time, since they are all matching sets. If you
accidentally mix up the cutters and guards, it may take
several weeks before optimal shaving performance is
restored.
- Remove the cutter from the shaving guard and
clean it with the brush.
ENGLISH16

- Clean the inside and outside of the shaving guard
with the brush.
6 Put the shaving heads back into the shaving
unit.
Make sure that the projections of the shaving
heads fit exactly into the recesses.
7 Put the retaining frame back into the shaving
unit and turn the lock clockwise.
8 Insert the lug of the shaving unit into the slot
in the top of the shaver (1).Then close the
shaving unit (2).
Note: If the shaving unit does not close smoothly, check
if you have inserted the shaving heads properly and if
the retaining frame is locked.
Cleaning the trimmer with the cleaning
brush (AT940/AT921/AT893/AT890 only)
Clean the trimmer every time you have used it.
1 Switch off the shaver.
2 Push the trimmer slide downwards to open
the trimmer.
3 Clean the trimmer with the short-bristled side
of the cleaning brush. Brush up and down along
the trimmer teeth.
4 Close the trimmer (‘ click’).
ENGLISH 17

Tip: For optimal trimming performance, lubricate the
trimmer teeth with a drop of sewing machine oil every
six months.
Storage
There are several ways to store the shaver or to
take it with you when you travel:
- Always put the protection cap on the shaver to
prevent damage.
- AT940/AT921/AT893/AT890 only: Store the
shaver in the pouch supplied.
- AT940/AT921 only: Store the shaver in the
charging stand.
Replacement
For maximum shaving performance, we advise
you to replace the shaving heads every year.
Replace damaged shaving heads right away.
Only replace the shaving heads with original HQ9
Philips Shaving Heads (for AT940/AT921) or HQ8
Philips Shaving Heads (for AT893/AT890/AT753/
AT752/AT750).
1 Switch off the shaver. Disconnect the shaver
from the mains or remove it from the charging
stand (AT940/AT921 only).
2 Press the release button to open the shaving
unit.
3 Pull the shaving unit off the shaver.
ENGLISH18

4 Turn the lock anticlockwise (1) and remove the
retaining frame (2).
5 Remove the shaving heads and place new ones
in the shaving unit.
Make sure that the projections of the shaving
heads fit exactly into the recesses.
6 Put the retaining frame back into the shaving
unit and turn the lock clockwise.
7 Insert the lug of the shaving unit into the slot
in the top of the shaver (1).Then close the
shaving unit (2).
Note: If the shaving unit does not close smoothly, check
if you have inserted the shaving heads properly and if
the retaining frame is locked.
Accessories
To retain the top performance of your shaver, make
sure you clean it regularly and replace its shaving
heads at the recommended time.
Shaving heads
- We advise you to replace your shaving heads
every year. Always replace with HQ9 Philips
Shaving Heads (for AT940/AT921) or HQ8 Philips
Shaving Heads (for AT893/AT890/AT753/AT752/
AT750).
Cleaning
- Use Cleaning spray (HQ110) to clean the shaving
heads thoroughly.
ENGLISH 19

Environment
- Do not throw away the appliance with the normal
household waste at the end of their life, but
hand them in at an official collection point for
recycling. By doing this, you help to preserve the
environment.
- The built-in rechargeable shaver battery contains
substances that may pollute the environment.
Always remove the battery before you discard or
hand in the shaver at an official collection point.
Dispose of the battery at an official collection
point for batteries. If you have trouble removing
the battery, you can also take the appliance to a
Philips service centre.The staff of this centre will
remove the battery for you and will dispose of it
in an environmentally safe way.
Removing the rechargeable shaver battery
Only remove the rechargeable battery when you
discard the shaver. Make sure the rechargeable
battery is completely empty when you remove it.
1 Disconnect the shaver from the mains or
remove it from the charging stand (AT940/
AT921 only).
2 Let the shaver run until it stops.
3 Undo the screws in the back of the shaver and
in the hair chamber.
4 Remove the front panel and the back panel.
5 Bend the 6 hooks aside and take out the
power unit.
ENGLISH20