Philips HQ7890/22 User manual

HQ7895, HQ7890

1 2 3 4
56 7 8
9 10 11 12
13 14 15 16
17 18 19 20

HQ7895, HQ7890
ENGLISH 6
DANSK 18
DEUTSCH 30
ESPAÑOL 44
SUOMI 57
FRANÇAIS 69
NEDERLANDS 82
NORSK 95
 107
SVENSKA 120
ITALIANO 132

6
Introduction
Congratulations on your purchase and welcome to Philips! To fully benet
from the support that Philips offers, register your product at
www.philips.com/welcome.
Important
Read this user manual carefully before you use the shaver and the
Jet Clean system. Save the user manual for future reference.
Danger
- Make sure the adapter does not get wet (Fig. 1).
Warning
- Be careful with hot water.Always check if the water is not too hot,
to prevent your hands from getting burnt.
- The adapter contains a transformer. Do not cut off the adapter to
replace it with another plug, as this causes a hazardous situation.
- The shaver and the Jet Clean system are not intended for use by
persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliances by a
person responsible for their safety.
- Children should be supervised to ensure that they do not play with
the shaver and the Jet Clean system.
Caution
- Do not use the shaver or the Jet Clean system if it is damaged.
- Do not immerse the shaver in water (Fig. 2).
- This shaver is not suitable for shaving in the shower.
- Charge, use and store the shaver at a temperature between 5°C and
35°C.
- Water may leak from the socket at the bottom of the shaver when
you rinse it.This is normal and not dangerous because all electronics
are enclosed in a sealed power unit inside the shaver (Fig. 3).
- Always put the protection cap on the shaver to protect the shaving
heads when you are travelling.
ENGLISH

- The shaver, the Jet Clean system and the other accessories are not
dishwasher-proof.
- Only use the adapter supplied.
- If the adapter is damaged, always have it replaced with one of the
original type in order to avoid a hazard.
- Only use the Jet Clean systemwith the original HQ200 cleaning uid.
- Do not immerse the Jet Clean system in water nor rinse it under the
tap. (Fig. 4)
- Use and store the Jet Clean system at a temperature between 5°C
and 35°C.
- Always place the Jet Clean system on a stable, level and horizontal
surface to prevent leakage.
- Always place the Jet Clean system on a uid-resistant surface.
- When the Jet Clean system is ready for use, do not move it to prevent
leakage of cleaning uid.
- The Jet Clean system thoroughly cleans but does not disinfect your
shaver, therefore do not share the shaver with others.
Compliance with standards
- The shaver complies with the internationally approved IEC safety
regulations and can be safely cleaned under the tap (Fig. 5).
- The shaver and the Jet Clean system comply with all standards
regarding electromagnetic elds (EMF). If handled properly and
according to the instructions in this user manual, the appliances are
safe to use based on scientic evidence available today.
General
- The adapter transforms 100-240 volts to a safe low voltage of less
than 24 volts.
ENGLISH 7

Charging
Make sure the shaver is switched off before you charge it.
Charging takes approx. 1 hour.
You can also shave without charging by connecting the shaver to the mains.
A fully charged shaver has a cordless shaving time of up to 55 minutes.
1 Chargetheshaverwhenthebottomlightashesorange.
Charge indications
Charging
- When you start charging the empty shaver, the bottom light ashes
orange.When the battery contains enough power for one shave, the
middle charging light starts ashing green (Fig. 6).
Battery fully charged
- When the battery is fully charged, the top charging light lights up
green continuously.
Battery low
- When the battery is almost empty i.e. when there are only 5 or less
shaving minutes left, the bottom charging light starts to ash orange.
When you switch off the shaver, this light still ashes orange a few times.
Charging with the adapter
1 Puttheapplianceplugintheshaver(Fig.7).
2 Puttheadapterinthewallsocket.
3 Remove the adapter from the wall socket and pull the appliance
plugoutoftheshaverwhenthebatteryisfullycharged.
Charging in the Jet Clean system
1 Place the shaver in the holder and completely push down the lever
tolocktheshaverintoplace(Fig.8).
,ThecharginglightontheJetCleansystemashestoindicatethat
theshaverischarging.
,Whenthecharginglightlightsupcontinuously(afterapprox.1
hour),theshaverisfullycharged(Fig.9).
ENGLISH8

2 Movetheleverupwardsuntilitdoesnotgoanyfurther(1)and
removetheshaverfromtheJetCleansystem(2).(Fig.10)
,Thecharginglightgoesout.
Using the shaver
Shaving
1 Presstheon/offbuttononcetoswitchontheshaver.
2 Move the shaving heads over your skin in circular
movements(Fig.11).
- Shaving on a dry face gives the best results.
- Your skin may need 2 or 3 weeks to get accustomed to the Philips
shaving system.
Note: Do not make straight movements.
3 Presstheon/offbuttononcetoswitchofftheshaver.
4 Cleantheshaver(seechapter‘Cleaningandmaintenance’).
5 Puttheprotectioncapontheshavereverytimeyouhaveusedit,
topreventdamage(Fig.12).
Trimming
You can use the trimmer to groom your sideburns and moustache.
1 Pushtheslidedownwardstoopenthetrimmer(Fig.13).
Note:You can activate the trimmer while the motor is running.
2 Closethetrimmer(‘click’)(Fig.14).
ENGLISH 9

Cleaning and maintenance
The best and most hygienic way to clean the shaver is in the Jet Clean
system.You can also clean the shaver by rinsing it under the tap or with
the brush supplied.
Regular cleaning guarantees better shaving performance.
Note:Water may leak from the socket at the bottom of the shaver when you
rinse it.This is normal and not dangerous.
Cleaning the shaver in the Jet Clean system supplied
Preparing the Jet Clean system for use
Fill the cleaning chamber before rst use and when the cleaning light
ashes to indicate that the uid level is too low. When the uid level
drops below the minimum level, the cleaning light ashes with intervals
and the holder returns to its starting position.
If you use the Jet Clean system to clean the shaver every day, rell the
cleaning chamber approx. every 15 days.
1 Simultaneously press the release buttons on both sides of the
cleaningchamber(1)andlifttheJetCleansystemoffthecleaning
chamber(2)(Fig.15).
The cleaning chamber remains behind.
2 Unscrew the dosing cap from the bottle with HQ200 Cleaning
Fluidandremovetheairtightseal.
3 FillthecleaningchamberwithcleaninguiduptotheMAX
indication(Fig.16).
4 PlacetheJetCleansystembackontothecleaningchamber(Fig.17).
Make sure the release buttons snap back into place.
5 Put the appliance plug in the Jet Clean system and put the adapter
inthewallsocket(Fig.18).
,Theholderautomaticallymovestothehighestposition.
The Jet Clean system is now ready for use.
ENGLISH10