Philips HQ8174CC User manual

HQ8174CC, HQ8170CC
ENGLISH 4
DEUTSCH 20
ESPAÑOL 38
FRANÇAIS 56
ITALIANO 73
NEDERLANDS 90
PORTUGUÊS 108
TÜRKÇE 126

4
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benet from the support that Philips
offers, register your product at
www.philips.com/welcome.
Important
Read this user manual carefully before you use the
shaver and the washing machine and save it for
future reference.
The shaver and the washing machine are not
intended for use by persons (including children)
with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of these appliances by
a person responsible for their safety.
Children should be supervised to ensure that
they do not play with the shaver or the washing
machine.
Only use the powerplug supplied.
The powerplug transforms 100-240 volts to a safe
low voltage of less than 24 volts.
The powerplug contains a transformer. Do not cut
off the powerplug to replace it with another plug,
as this causes a hazardous situation.
Do not use a damaged powerplug.
If the powerplug is damaged, always have it
replaced with one of the original type in order to
avoid a hazard.
Make sure the powerplug does not get wet.
Charge, use and store the shaver at a temperature
between 5°C and 35°C.
Do not recharge the shaver in a closed pouch.
-
-
-
-
-
-
-
-
-
-
ENGLISH

Always unplug the shaver before you clean it
under the tap.
The shaver complies with the internationally
approved IEC safety regulations and can be safely
cleaned under the tap.
Be careful with hot water.Always check if the
water is not too hot, to prevent your hands from
getting burnt.
This washable shaver is not suitable for shaving in
the shower.
Do not immerse the shaver in water.
Water may leak from the socket at the bottom
of the shaver when you rinse it.This is normal
and not dangerous because all electronics are
enclosed in a sealed power unit inside the shaver.
Only use the washing machine with the original
HQ200 Cleaning Fluid.
Empty the cleaning chamber and rinse it
thoroughly with hot tap water every 15 days.
The washing machine thoroughly cleans but does
not disinfect your shaver, therefore do not share
the shaver with others.
Never immerse the washing machine in water nor
rinse it under the tap.
Use and store the washing machine at a
temperature between 5°C and 35°C.
Always place the washing machine on a stable,
level and horizontal surface to prevent leakage.
Always place and use the washing machine on a
surface that is uid-resistant.
When the washing machine is ready for use, do
not move it to prevent leakage of cleaning uid.
-
-
-
-
-
-
-
-
-
-
-
-
-
-
ENGLISH 5

Electromagnetic elds (EMF)
These Philips appliances comply with all standards
regarding electromagnetic elds (EMF). If handled
properly and according to the instructions in this
user manual, the appliances are safe to use based on
scientic evidence available today.
Charging
Make sure the shaver is switched off before you
charge it.
Charging takes approx. 1 hour.
You can also shave without charging by connecting
the shaver to the mains.
A fully charged shaver has a cordless shaving time of
up to 55 minutes.
1 Charge the shaver when the bottom light
burns or ashes red.
Charge indications
Charging
When you start to charge the empty shaver,
the bottom light ashes red. When the battery
contains enough power for one shave, all
lights ash green sequentially.
Battery fully charged
When the battery is fully charged, all lights burn
green.
A few hours after charging, all lights go out.
Remaining battery capacity
The number of lights that are on show how
much power is left in the battery. The battery
capacity is only shown when you switch the
shaver on or off.
,
,
,
ENGLISH6

When all lights burn green, the battery is 100%
charged.
When the bottom light burns green, 20% of the
battery capacity is left.
Battery running low
When the battery is running low, the bottom
light turns red.
When you switch off the shaver, this light ashes a
few times.
Charging with the powerplug
Do not recharge the shaver in a closed pouch.
1 Put the appliance plug in the shaver.
2 Put the powerplug in the wall socket.
3 Remove the powerplug from the wall socket
and pull the appliance plug out of the shaver
when the battery is fully charged.
Charging in the washing machine
1 Place the shaver in the holder and push the
lever down completely to lock the shaver into
place.
The charging light on the washing machine ashes to
indicate that the shaver is charging.
When the charging light lights up continuously
(after approx. 1 hour), the shaver is fully charged.
-
-
,
,
ENGLISH 7

2 Move the lever upwards until it does not go
any further (1) and remove the shaver from the
washing machine (2).
The charging light goes out.
Using the shaver
Shaving
1 Press the on/off button once to switch on the
shaver.
The blue light ring round the on/off button goes on
to indicate that the motor is running.
Note:When you switch on the shaver, all lights go on
and then the remaining battery capacity is shown for a
few seconds.
2 Move the shaving heads quickly over your skin.
Make both straight and circular movements.
Shaving on a dry face gives the best results.
Your skin may need 2 or 3 weeks to get
accustomed to the Philips shaving system.
3 Press the on/off button once to switch off the
shaver.
The blue light ring round the on/off button goes out.
4 Clean the shaver (see chapter ‘Cleaning and
maintenance’).
5 Put the protection cap on the shaver every
time you have used it, to prevent damage.
-
-
ENGLISH8

Trimming
You can use the trimmer to groom your sideburns
and moustache.
1 Push the slide downwards to open the
trimmer.
You can activate the trimmer while the motor is
running.
2 Close the trimmer (‘click’).
Cleaning and maintenance
The best and most hygienic way to clean the
shaver is in the washing machine. You can also
clean the shaver by rinsing it under the tap or
with the brush supplied.
The light above the tap symbol starts to ash
after every shave to remind you that the shaver
needs to be cleaned (except when the bottom
light burns red).
Regular cleaning guarantees better shaving
performance.
Note:Water may leak from the socket at the bottom
of the shaver when you rinse it.This is normal and not
dangerous.
Cleaning the shaver in the washing machine
supplied
Preparing the washing machine for use
Fill the cleaning chamber before rst use and when
the cleaning light ashes to indicate that the uid
,
,
ENGLISH 9

level is too low. When the uid level drops below
the minimum level, the cleaning light ashes with
intervals and the holder returns to its starting
position.
If you use the washing machine to clean the shaver
every day, rell the cleaning chamber approx. every
15 days.
1 Simultaneously press the release buttons on
both sides of the cleaning chamber (1) and lift
the washing machine off the cleaning chamber
(2).
The cleaning chamber remains behind.
2 Unscrew the dosing cap from the bottle with
HQ200 Cleaning Fluid and remove the airtight
seal.
3 Fill the cleaning chamber with cleaning uid up
to the MAX indication.
4 Place the washing machine back onto the
cleaning chamber.
Make sure the release buttons snap back into place.
5 Put the appliance plug in the washing machine
and put the powerplug in the wall socket.
The holder automatically moves to the highest
position.
The washing machine is now ready for use.
Using the washing machine
1 Place the shaver in the holder and push the
lever down completely to lock the shaver into
place.
The charging light on the washing machine ashes to
indicate that the shaver is being charged.
ENGLISH10

2 Press the start button to start the cleaning
program.
The cleaning light starts to ash and the shaver is
automatically lowered into the cleaning uid.
During the cleaning program, which takes
approx. 1 hour, the cleaning light ashes
continuously.
During the rst phase of the cleaning program,
the shaver automatically switches on and off
several times and is put in different positions.
During the second phase of the cleaning
program, the shaver is placed in the drying
position. It stays in this position until the end
of the program. The cleaning light lights up
continuously.
After the cleaning program, the shaver
automatically returns to its starting position and
the charging program is started. The charging
light ashes.
Note: If you press the start button or open the lever
during cleaning, the cleaning program is aborted and
reset. In this case, the cleaning light stops ashing and
the holder returns to its starting position.
Note: If the powerplug is removed from the wall socket
during cleaning, the cleaning program is aborted.
The holder remains in its current position.When
the powerplug is put back into the wall socket, the
holder moves to the highest position.
Note: If the uid volume in the cleaning chamber drops
below the minimum level during the cleaning program,
the program is aborted. The cleaning light ashes with
intervals and the holder returns to its starting position.
,
,
,
,
ENGLISH 11

Cleaning the washing machine
The cleaning chamber is not dishwasher-proof.
Clean the cleaning chamber every two weeks.
1 Simultaneously press the buttons on both sides
of the washing machine (1) and lift the washing
machine off the cleaning chamber (2).
The cleaning chamber remains behind.
2 Pour any remaining cleaning uid out of the
cleaning chamber.
You can simply pour the cleaning uid down the sink.
3 Rinse the cleaning chamber under the tap.
4 Place the washing machine back onto the
cleaning chamber.
Make sure the release buttons snap back into place.
5 Clean the washing machine with a moist cloth.
Cleaning the shaver under the tap
Be careful with hot water. Always check if the
water is not too hot, to prevent your hands from
getting burnt.
1 Switch off the shaver, remove the powerplug
from the wall socket and pull the appliance plug
out of the shaver.
,
,
ENGLISH12

2 Press the release button to open the shaving
unit.
3 Rinse the shaving unit and the hair chamber
under a hot tap for some time.
Make sure you clean the inside as well as the
outside of the shaving unit.
4 Close the shaving unit and shake off excess
water.
Never dry the shaving unit with a towel or tissue,
as this may damage the shaving heads.
5 Open the shaving unit again and leave it open
to let the shaver dry completely.
You can also clean the hair chamber without water
with the brush supplied.
Cleaning the shaver with the brush supplied
Shaving heads
1 Open the shaving unit, turn the lock
anticlockwise (1) and remove the retaining
frame (2).
,
ENGLISH 13

2 Clean the cutters and guards with the brush
supplied.
Do not clean more than one cutter and guard
at a time, since they are all matching sets. If you
accidentally mix up the cutters and guards, it
may take several weeks before optimal shaving
performance is restored.
3 Put the shaving heads back into the shaving
unit. Put the retaining frame back into the
shaving unit and turn the lock clockwise.
4 Close the shaving unit.
Trimmer
Clean the trimmer every time you have used it.
1 Switch off the shaver, remove the powerplug
from the wall socket and pull the appliance plug
out of the shaver.
2 Clean the trimmer with the brush supplied.
3 Lubricate the trimmer teeth with a drop of
sewing machine oil every six months.
Storage
Put the protection cap on the shaver to prevent
damage.
,
ENGLISH14

Store the shaver in the pouch or place it in the
washing machine.
Replacement
Replace the shaving heads as soon as the light
above the shaving unit symbol starts to ash.
Replace damaged or worn shaving heads with HQ9
Philips Shaving Heads only.
Note: Do not mix up the cutters and the guards to
guarantee optimal shaving performance.
1 Switch off the shaver, remove the powerplug
from the wall socket and pull the appliance plug
out of the shaver.
2 Press the release button to open the shaving
unit.
3 Turn the lock anticlockwise (1) and remove the
retaining frame (2).
4 Remove the shaving heads and place new ones
in the shaving unit. Put the retaining frame
back into the shaving unit and turn the lock
clockwise.
Make sure that the projections of the shaving
heads t exactly into the recesses.
5 Close the shaving unit.
,
,
ENGLISH 15

Accessories
The following accessories are available:
HQ8500/HQ8000 powerplug.
HQ9 Philips Shaving Heads.
HQ110 Philips Shaving Head Cleaning Spray.
HQ8010 Car Cord.
HQ200 Philips Cleaning Fluid.
Environment
Do not throw away the appliances with the
normal household waste at the end of their life,
but hand them in at an ofcial collection point for
recycling. By doing this, you help to preserve the
environment.
The built-in rechargeable shaver battery contains
substances that may pollute the environment.
Always remove the battery before you discard
and hand in the shaver at an ofcial collection
point. Dispose of the battery at an ofcial
collection point for batteries. If you have trouble
removing the battery, you can also take the shaver
to a Philips service centre.The staff of this centre
will remove the battery for you and will dispose of
it in an environmentally safe way.
Disposal of the battery
Only remove the battery if it is completely empty.
1 Remove the powerplug from the wall socket
and pull the appliance plug out of the shaver.
2 Let the shaver run until it stops and undo the
two screws in the back of the shaver.
-
-
-
-
-
-
-
ENGLISH16

3 Undo the two screws in the hair chamber.
4 Undo the three screws in the power unit.
5 Bend the 4 hooks aside (1) to take out the
power unit (2).
Be careful, the hooks are very sharp.
6 Remove the power unit cover with a
screwdriver.
7 Remove the battery.
Be careful, the battery strips are very sharp.
Do not connect the shaver to the mains again after
you have removed the battery.
Guarantee & service
If you need information or if you have a problem,
please visit the Philips website at www.philips.com
or contact the Philips Customer Care Centre
in your country (you nd its phone number in
the worldwide guarantee leaet). If there is no
Customer Care Centre in your country, go to
your local Philips dealer or contact the Service
ENGLISH 17

Department of Philips Domestic Appliances and
Personal Care BV.
Guarantee restrictions
The shaving heads (cutters and guards) are not
covered by the terms of the international guarantee
because they are subject to wear.
Frequently asked questions
1 Why does the shaver not shave as well as it
used to?
The washing machine may not have cleaned the
shaver properly, because the cleaning uid in the
cleaning chamber is soiled or the cleaning uid
level is too low. Clean the shaver thoroughly
before you continue shaving. If necessary, clean
and rell the cleaning chamber (see chapter
‘Cleaning and maintenance’).
Long hairs may obstruct the shaving heads. Clean
the cutters and guards with the brush supplied
(see chapter ‘Cleaning and maintenance’).
The shaving heads may be damaged or
worn. Replace the shaving heads (see chapter
‘Replacement’).
2 Why does the shaver not work when I press
the on/off button?
The battery may be empty. Recharge the battery
(see chapter ‘Charging’).
The shaver may not be connected to the mains.
Put the appliance plug in the shaver and put the
powerplug in the wall socket.
3 Why does the shaving unit come off the
shaver?
,
,
,
,
,
ENGLISH18

The shaving unit may not be placed correctly.
Put the shaving unit back onto the shaver by
inserting the hinge into the slot in the rim of the
hair chamber. Then push the shaving unit home
until it locks into place (‘click’).
4 Why is the shaver not entirely clean after I
have cleaned it in the washing machine?
The cleaning uid in the cleaning chamber may
be soiled. Empty and rinse the cleaning chamber.
The cleaning uid level may be too low. If the
uid volume in the cleaning chamber drops
below the minimum level during the cleaning
program, the program is aborted. The cleaning
light ashes with intervals and the holder
returns to its starting position. Rell the
cleaning chamber with cleaning uid up to the
MAX indication (see chapter ‘Cleaning and
maintenance’).
5 Why does the washing machine not work
when I press the start button?
The washing machine may not be connected to
the mains. Put the appliance plug in the washing
machine and put the powerplug in the wall
socket.
There may not be an electrical connection
between the washing machine and the shaver.
Open the lever and close it again until the
charging light on the washing machine starts to
ash.
,
,
,
,
,
ENGLISH 19

20
Einführung
Herzlichen Glückwunsch zu Ihrem Kauf und
willkommen bei Philips! Um den Support von Philips
optimal zu nutzen, registrieren Sie Ihr Produkt bitte
unter www.philips.com/welcome.
Wichtig
Lesen Sie diese Bedienungsanleitung vor dem
Gebrauch des Rasierers und des Reinigungsgeräts
aufmerksam durch und bewahren Sie sie für eine
spätereVerwendung auf.
Der Rasierer und das Reinigungsgerät sind für
Benutzer (einschl. Kinder) mit eingeschränkten
physischen, sensorischen oder psychischen
Fähigkeiten bzw. ohne jegliche Erfahrung oder
Vorwissen nur dann geeignet, wenn eine
angemessene Aufsicht oder ausführliche Anleitung
zur Benutzung dieser Geräte durch eine
verantwortliche Person sichergestellt ist.
Achten Sie darauf, dass Kinder nicht mit dem
Rasierer und dem Reinigungsgerät spielen.
Verwenden Sie mit diesem Gerät ausschließlich
das mitgelieferte Netzteil.
Das Netzteil wandelt Netzspannungen von 100
bis 240Volt in eine sichere Betriebsspannung von
unter 24Volt um.
Das Netzteil enthält einenTransformator. Ersetzen
Sie das Netzteil keinesfalls durch einen anderen
Stecker, da dies den Benutzer gefährden kann.
Benutzen Sie keinesfalls ein beschädigtes Netzteil.
Wenn das Netzteil defekt oder beschädigt ist, darf
es nur durch ein Original-Ersatzteil ausgetauscht
werden, um Gefährdungen zu vermeiden.
Achten Sie darauf, dass das Netzteil nicht nass
wird.
-
-
-
-
-
-
-
-
DEUTSCH

21
Benutzen und laden Sie den Rasierer bei
Temperaturen zwischen 5° C und 35°
C. Bewahren Sie ihn auch in diesem
Temperaturbereich auf.
Nehmen Sie den Rasierer zum Laden aus der
Tasche.
Ziehen Sie stets das Netzteil aus der Steckdose,
bevor Sie den Rasierer unter ießendem Wasser
reinigen.
Der Rasierer erfüllt die internationalen IEC-
Sicherheitsvorschriften und kann ohne Bedenken
unter ießendem Wasser gereinigt werden.
Gehen Sie vorsichtig mit heißem Wasser um.
Achten Sie darauf, dass das Wasser nicht zu heiß
ist und Sie sich nicht die Hände verbrühen.
Dieser abwaschbare Rasierer eignet sich nicht für
die Rasur unter der Dusche.
Tauchen Sie den Rasierer nicht in Wasser.
Möglicherweise tritt beim Abspülen des Geräts
Wasser aus der Buchse unten am Rasierer aus.
Das ist normal und völlig ungefährlich, da die
gesamte Elektronik im Inneren des Rasierers
versiegelt ist.
Verwenden Sie zum Säubern des Rasierers nur
das Reinigungsgerät mit der HQ200 Original-
Reinigungsüssigkeit.
Entleeren Sie die Reinigungskammer alle 2 Wochen
und spülen Sie sie gründlich unter ießendem
heißen Wasser aus.
Das Reinigungsgerät reinigt Ihren Rasierer
gründlich, desinziert ihn jedoch nicht. Deshalb
sollten Sie Ihren Rasierer nicht mit anderen
Personen teilen.
-
-
-
-
-
-
-
-
-
-
-
DEUTSCH 21

22
Tauchen Sie das Reinigungsgerät niemals in Wasser.
Spülen Sie es auch nicht unter ießendem Wasser
ab.
Verwenden Sie das Reinigungsgerät bei einer
Temperatur zwischen 5°C und 35°C. Bewahren
Sie es auch in diesemTemperaturbereich auf.
Stellen Sie das Reinigungsgerät stets auf eine
stabile, ebene und waagerechte Unterlage, um
Auslaufen von Flüssigkeit zu vermeiden.
Stellen Sie das Reinigungsgerät immer auf eine
wasserundurchlässige Oberäche.
Wenn das Reinigungsgerät betriebsbereit ist,
darf es nicht bewegt werden, damit keine
Reinigungsüssigkeit ausläuft.
Elektromagnetische Felder (EMF; Electro
Magnetic Fields)
Diese Philips Geräte erfüllen sämtliche Normen
bezüglich elektromagnetischer Felder (EMF).
Nach aktuellen wissenschaftlichen Erkenntnissen
sind die Geräte sicher im Gebrauch, sofern sie
ordnungsgemäß und entsprechend den Anweisungen
in dieser Bedienungsanleitung gehandhabt werden.
Laden
Bei Beginn des Ladevorgangs muss der Rasierer
ausgeschaltet sein.
Die Ladedauer beträgt ca. 1 Stunde.
Sie können sich auch bei leerem Akku rasieren,
indem Sie den Rasierapparat an das Netz
anschließen.
Mit vollständig aufgeladenem Akku können Sie sich
bis zu 55 Minuten kabellos rasieren.
-
-
-
-
-
DEUTSCH22