Philips PQ225 User manual

ENGLISH
Introduction
Congratulations on your purchase and
welcome to Philips! To fully benet from
the support that Philips offers, register your
product at www.philips.com/welcome.
General description (Fig. 1)
1 Protection cap
2 Shaving heads
3 Shaving unit
4 Hair chamber
5 On/off button
6 Charging light
7 Socket for micro USB plug
8 Wheel of retaining frame
9 Retaining frame
10 Cutter
11 Guard
12 Release button
13 Cleaning brush
14 Adapter
15 Micro USB plug
16 Storage pouch (PQ288 only)
17 Philips Cleaning Spray (HQ110)
(Optional)
Important
Read this user manual carefully before you
use the appliance and save it for future
reference.
Danger
- Warning: Keep the appliance and the
adapter dry.
- This symbol means: Forbidden to clean
under a running tap (Fig. 2).
Warning
- The adapter contains a transformer.
Do not cut off the adapter to replace
it with another plug, as this causes a
hazardous situation.
- Warning: Do not use this appliance
close to a bathtub, shower or other
containers lled with water.
- This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning
use of the appliance by a person
responsible for their safety.
- Children should be supervised to
ensure that they do not play with the
appliance.
Caution
- Do not use the shaver or the adapter
if it is damaged.
- Only use the adapter supplied to
charge the appliance.
- If the adapter is damaged, always have
it replaced with one of the original type
in order to avoid a hazard.
- Charge, use and store the shaver at a
temperature between 5°C and 35°C.
- Do not use the shaver in combination
with pre-shave lotions, creams, foams,
gels or other cosmetic products.
General
- The adapter transforms 100-240 volts
to a safe low voltage of less than
24 volts.
Compliance with standards
- This Philips appliance complies with all
standards regarding electromagnetic
elds (EMF). If handled properly
and according to the instructions in this
user manual, the appliance is safe to use
based on scientic evidence available
today.
- This shaver complies with the
applicable IEC safety standards.
Charging
Make sure the shaver is switched off when
you start to charge it.
When you charge the shaver for the rst
time or after a long period of non-use, let it
charge continuously for 12 hours. Charging
normally takes approx. 8 hours.
Charge the appliance when the motor
stops or starts running slower.
For optimal performance, only charge the
shaver when the battery is low.
Do not leave the appliance connected to
the mains for more than 24 hours.
1 Put the micro USB plug in the
shaver (Fig. 3).
2 Put the adapter in the wall socket.
,The charging light goes on to indicate
that the appliance is charging (Fig. 4).
Note: Charge the shaver for at least 8 hours
but not more than 24 hours.
PQ288, PQ229, PQ225, PQ222
Register your product and get support at
www.philips.com/welcome
4222.002.5273.3
2 3 4
5 6 7
8 9 10
11 12 13
14 15 16
17 18 19
20 21 22
23 24 25
1

3 Remove the adapter from the wall
socket and pull the micro USB plug
out of the shaver when the battery is
fully charged (Fig. 5).
Note:The shaver does not run from the mains.
When the battery is empty, you have to
recharge the battery before you can use the
shaver again.
Cordless shaving time
A fully charged shaver has a cordless shaving
time of approximately 30 minutes.
Using the appliance
Note:The shaver cannot be used directly from
the mains.
1 Remove the protection cap.
2 Press the on/off button to switch on
the shaver (Fig. 6).
3 Move the shaving heads over your
skin. Make both straight and circular
movements (Fig. 7).
Note: Shave on a dry face only. Do not use the
shaver in combination with gel, foam or water.
Note:Your skin may need 2 or 3 weeks to get
accustomed to the Philips shaving system.
4 Press the on/off button to switch off
the shaver.
5 Clean the shaver after every
shave (see chapter ‘Cleaning and
maintenance’).
6 Put the protection cap on the shaver
to prevent damage and to avoid
dirt accumulation in the shaving
heads (Fig. 8).
Note: Make sure that the lug of the protection
cap covers the release button.
Cleaning and maintenance
Never use scouring pads, abrasive cleaning
agents or aggressive liquids such as petrol
or acetone to clean the appliance.
Clean the shaver after every shave to
guarantee better shaving performance. For
the best cleaning result, we advise you to
use Philips Cleaning Spray (HQ110). Ask
your Philips dealer for information.
Note: Philips Shaving Head Cleaning
Spray (HQ110) may not be available in all
countries. Contact the Consumer Care Centre
in your country about the availability of this
accessory.
After every shave: shaving
unit and hair chamber
1 Switch off the shaver, remove the
adapter from the wall socket and pull
the micro USB plug out of the shaver.
2 Clean the top of the appliance with
the cleaning brush supplied (Fig. 9).
3 Press the release button (1) and pull
the shaving unit in a straight upward
movement off the shaver (2). (Fig. 10)
4 Clean the inside of the shaving unit
with the cleaning brush (Fig. 11).
5 Clean the hair chamber with the
cleaning brush (Fig. 12).
6 Put the shaving unit back onto the
shaver (Fig. 13).
Every two months: shaving
heads
Note: Do not use cleaning agents or alcohol
to clean the shaving heads. Only use Philips
Cleaning Spray (HQ110).
1 Switch off the shaver, remove the
adapter from the wall socket and pull
the small plug out of the shaver.
2 Press the release button (1) and pull
the shaving unit in a straight upward
movement off the shaver (2) (Fig. 10).
3 Turn the orange wheel anticlockwise
(1) and remove the retaining frame
(2) (Fig. 14).
4 Remove and clean one shaving head
at a time. Each shaving head consists
of a cutter and a guard (Fig. 15).
Note: Do not clean more than one cutter and
guard at a time, since they are all matching
sets. If you accidentally mix up the cutters
and guards, it may take several weeks before
optimal shaving performance is restored.
5 Remove the guard from the
cutter (Fig. 16).
6 Clean the cutter with the short-
bristled side of the cleaning brush.
Brush carefully in the direction of the
arrows (Fig. 17).
7 Clean the guard with the long-bristled
side of the cleaning brush (Fig. 18).
8 Put the cutter back into the guard
after cleaning (Fig. 19).
9 Put the shaving heads back into the
shaving unit (Fig. 20).
10 Put the retaining frame back into the
shaving unit (1) and turn the orange
wheel clockwise (2) (Fig. 21).
11 Put the shaving unit back onto the
shaver (Fig. 13).
Storage
Keep the appliance dry.
Use and store the appliance at a
temperature between 5°C and 35°C.
1 Switch off the shaver.
2 Put the protection cap on the shaver
after use to prevent damage and to
avoid dirt accumulation in the shaving
heads (Fig. 8).
Note: Make sure that the lug of the protection
cap covers the release button.
3 Put the shaver in the storage pouch
(PQ288 only).
Replacement
Replace the shaving heads every two years
for optimal shaving results.
Replace damaged or worn shaving heads
with Philips shaving heads only (HQ4+ for
China or HQ56 for the rest of the world).
For instructions on how to remove the
shaving heads, see chapter ‘Cleaning and
maintenance’, section ‘Every two months:
shaving heads’.
Ordering accessories
To purchase accessories for this
appliance, please visit our online shop at
www.shop.philips.com/service. If the
online shop is not available in your country,
go to your Philips dealer or a Philips service
centre. If you have any difculties obtaining
accessories for your appliance, please
contact the Philips Consumer Care Centre
in your country. You nd its contact details
in the worldwide guarantee leaet.
To retain the top performance of your
shaver, make sure you clean it regularly
and replace its shaving heads at the
recommended time.
Shaving heads
- We advise you to replace your shaving
heads every two years. Always replace
them with Philips shaving heads only
(HQ4+ for China or HQ56 for the
rest of the world) (Fig. 22).
Cleaning
- Use Philips Cleaning Spray (HQ110) to
clean the shaving heads thoroughly.
Environment
- Do not throw away the appliance
with the normal household waste at
the end of its life, but hand it in at an
ofcial collection point for recycling.
By doing this, you help to preserve the
environment (Fig. 23).
- The built-in rechargeable battery
contains substances that may pollute
the environment. Remove the battery
before you discard and hand in the
appliance at an ofcial collection point.
Dispose of the battery at an ofcial
collection point for batteries. If you
have trouble removing the battery, you
can also take the appliance to a Philips
service centre.The staff of this centre
will remove the battery for you and will
dispose of it in an environmentally safe
way (Fig. 24).
Removing the rechargeable
battery
Only remove the rechargeable battery
when you discard the shaver. Make
sure the battery is completely empty
when you remove it.
1 Remove the adapter from the wall
socket and pull the micro USB plug
out of the shaver.
2 Let the shaver run until it stops and
undo the screw at the back of the
shaver (Fig. 25).
3 Remove the back panel of the shaver
with a screwdriver.
4 Remove the rechargeable battery.
Do not connect the shaver to the mains
again after you have removed the battery.
Guarantee and service
If you need service or information or if
you have a problem, please visit the Philips
website at www.philips.com/support or
contact the Philips Consumer Care Centre
in your country. You nd its phone number
in the worldwide guarantee leaet. If there
is no Consumer Care Centre in your
country, go to your local Philips dealer.
Guarantee restrictions
The shaving heads (cutters and guards)
are not covered by the terms of the
international guarantee because they are
subject to wear.
Troubleshooting
This chapter summarises the most common
problems you could encounter with the
appliance. If you are unable to solve the
problem with the information below, visit
www.philips.com/support for a list of
frequently asked questions or contact the
Consumer Care Centre in your country.
Problem Possible
cause
Solution
The
shaver
does not
shave as
well as it
used to.
The shaving
heads are
dirty.You
have not
cleaned the
shaver well
enough or
you have not
cleaned it for
a long time.
Clean the
shaving heads
thoroughly
before you
continue
shaving. See
chapter
‘Cleaning and
maintenance’.
Long
hairs obstruct
the shaving
heads.
Clean the
cutters and
guards with
the clean-
ing brush
supplied.
See chapter
‘Cleaning and
maintenance’,
section ‘Every
two months:
shaving
heads’.

简体中文
简介
感谢您的惠顾，欢迎光临飞利浦！
为了您能充分享受飞利浦提供的支持，
请在 www.philips.com/welcome
上注册您的产品。
基本说明 (图 1)
1 保护盖
2 剃须刀头
3 剃毛刀头部件
4 毛发储藏室
5 开/关按钮
6 充电指示灯
7 微型 USB 插头接口
8 固定架的滚轮
9 固定架
10 刀片
11 网罩
12 释放钮
13 清洁刷
14 适配器
15 微型 USB 插头
16 存储袋（仅限于 PQ288）
17 飞利浦清洁喷雾剂 (HQ 110)
（可选）
注意事项
使用本产品之前，请仔细阅读本使用说
明书，并妥善保管以备日后参考。
危险
-警告：让产品和电源适配器保持
干燥。
-警告符号注释：禁止用在打开的水
龙头下进行清洗。 (图 2)
警告
-电源适配器内含有一个变压器。切
勿自行更换插头，否则将导致严重
后果。
-警告：不要在盛水的浴缸、淋浴、
洗脸盆或其他器皿附近使用本器
具。
-本产品不打算由肢体不健全、感觉
或精神上有障碍或缺乏相关经验和
知识的人（包括儿童）使用，除非
有负责他们安全的人对他们使用本
产品进行监督或指导。
-应照看好儿童，确保他们不玩耍本
产品。
注意
-如果剃须刀或适配器已损坏，请勿
再使用。
-为产品充电，须用随产品提供的电
源适配器。
Problem Possible
cause
Solution
You mixed
up the
cutters and
guards when
you placed
them back
into the
retaining
frame after
cleaning.
Put each
cutter in the
other guard.
If you do not
switch the
cutters, it
may take 2
to 3 weeks
until optimal
shaving
performance
is restored.
The shaving
heads are
damaged or
worn.
Replace
the shaving
heads. See
chapter ‘Re-
placement’.
The
shaver
does not
work
when I
press the
on/off
button.
The re-
chargeable
battery is
empty.
Recharge
the battery.
See chapter
‘Charging’.
My
skin is
irritated
after
shaving.
Your skin
needs time
to get used
to the Philips
shaving
system.
Skin irritation
during the
rst 2-3
weeks of use
is possible.
After this
period, the
skin irritation
usually disap-
pears.
The
rotation
speed
of the
shaving
heads is
slower
than
usual.
Too much
dirt has
collected in
the shaving
heads.
Clean the
shaving heads.
See chapter
‘Cleaning and
maintenance’.
The re-
chargeable
battery is
low.
Recharge
the battery.
See chapter
‘Charging’.
Problem Possible
cause
Solution
The ap-
pliance
makes a
strange
noise.
Too much
dirt has
collected in
the shaving
heads.
Clean the
shaving heads.
After clean-
ing, lubricate
the central
point on the
inside of the
guards with
Philips Clean-
ing Spray
(HQ110).
See chapter
‘Cleaning and
maintenance’.
The shaving
heads are
damaged or
worn.
Replace
the shaving
heads. See
chapter ‘Re-
placement’.
使用本产品
注意： 剃须刀不能连在电源上直接使
用。
1 取下保护盖。
2 按下开/关按钮启动剃须刀。 (图 6)
3 将剃须刀头在皮肤上移动。作直线
和迂回动作。 (图 7)
注意： 仅限在干爽的面部剃须。请勿
将本剃须刀与凝胶、剃须泡沫或水结
合使用。
注意： 您的皮肤可能需要 2 到 3 周才
能适应飞利浦剃须系统。
4 按开/关按钮关闭剃须刀电源。
5 每次剃须后均应清洁剃须刀（见“
清洁和保养”一章）。
6 请盖上剃须刀保护盖，以防止损坏
剃须刀头并避免其内积聚灰尘。
(图 8)
注意： 确保保护盖的凸缘盖住释放钮。
清洁和保养
不要使用钢丝球、研磨性清洁剂或腐
蚀性液体（例如汽油或丙酮）来清洁
产品。
每次剃须后均应清洁剃须刀，以保证
更好的剃须效果。为了获得最佳的清
洁效果，建议您使用飞利浦清洁喷雾
剂 (HQ110)。有关详情，请咨询飞利浦
经销商。
注意： 并非所有国家/地区都销售飞利
浦剃须刀头清洁喷雾剂 (HQ110)。请向
当地的客户服务中心了解是否有售。
每次剃须后：清洗剃须刀头部
件和胡茬储藏室
1 关闭剃须刀电源，从电源插座上拔
下适配器，并从剃须刀上拔下微型
USB 插头。
2 用随附的清洁刷清洁产品顶部。
(图 9)
3 按释放按钮 (1)，垂直向上移动剃须
刀头部件，将其从剃须刀 (2) 中拉
出。 (图 10)
4 用清洁刷清洁剃须刀头部件的内
侧。 (图 11)
5 用清洁刷清洁胡茬储藏室。 (图 12)
-如果适配器已损坏，则务必更换原
装型号适配器，以免发生危险。
-必须在 5 摄氏度至 35 摄氏度之间
的温度下充电、使用和存放剃须
刀。
-请勿将本剃须刀与剃须润滑液、面
霜、泡沫、凝胶或其它护肤产品结
合使用。
概述
-电源适配器可将 100-240 伏的电压
转换为 24 伏以下的安全低电压。
符合标准
-这款飞利浦产品符合关于电磁场
(EMF) 的相关标准。据目前的科学
证明，如果正确使用并按照本用户
手册中的说明进行操作，本产品是
安全的。
-这款剃须刀符合 IEC 家电安全标
准。
充电
请确保开始充电前，剃须刀电源已关
闭。
如果是第一次为剃须刀充电，或长时间
未使用后充电，应让其连续充电 12 小
时。充电通常需要约 8 小时。
当马达停转或转速开始下降时，为产
品充电。
为确保最佳性能，只能在电池电量不足
时为剃须刀充电。
不要将本产品与电源接通超过 24 小
时。
1 将微型 USB 插头插入剃须刀。
(图 3)
2 将电源适配器插入电源插座。
,充电指示灯亮起，表示剃须刀正在
充电。 (图 4)
注意： 至少让剃须刀充电 8 小时，但
不要超过 24 小时。
3 电池充满后，从电源插座上拔下适
配器，并从剃须刀上拔出微型 USB
插头。 (图 5)
注意： 本剃须刀不能插电使用。当电池
电量耗尽时，请在再次使用剃须刀前为
电池充电。
不接电源的剃须时间
完全充电的剃须刀在不连接电源的情况
下最长可使用达 30 分钟。

更换
每两年更换一次刀头以获得最佳的剃
须效果。
只能使用飞利浦剃须刀头（适用于中
国的 HQ4+ 或适用于世界其他各地的
HQ56）更换损坏或磨损的剃须刀头。
有关如何拆卸剃须刀头的说明，请参
阅“清洁和保养”一章中的“每两个
月：清洁剃须刀头”部分。
订购附件
要购买本产品的附件，请访问我们
的在线商城 www.shop.philips.com/
service。如果您的国家/地区没有在线
商城，请联系您的飞利浦经销商或飞利
浦服务中心。如果您购买产品的附件有
困难，请联系您所在国家/地区的飞利浦
客户服务中心。可在全球保修卡中找到
其详细联系信息。
为了保持剃须刀的最佳性能，请确保定
期清洁并在推荐的时间更换剃须刀头。
剃须刀头
-建议您每两年更换一次剃须刀头。
务必仅使用飞利浦剃须刀头（适用
于中国的 HQ4+ 或适用于世界其他
各地的 HQ56）进行更换。 (图 22)
清洁
-使用飞利浦清洁喷雾剂 (HQ110) 彻
底清洁剃须刀头。
环保
-弃置产品时，请不要将其与一般生
活垃圾堆放在一起；应将其交给官
方指定的回收点。这样做有利于环
保。 (图 23)
-内置充电电池含有可能会污染环境
的物质。弃置产品并将产品送到官
方指定的回收站之前，应将电池
取出。到官方指定的电池回收站处
理电池。如果您在取出电池时遇到
问题，您也可以将产品送至飞利浦
维修中心。维修中心的员工会帮您
取出电池，并以环保的方式进行处
理。 (图 24)
卸下充电电池
只有在丢弃剃须刀时才可取下充电电
池。请确保在取下电池时电量已完全
耗尽。
1 从电源插座上拔下适配器，并从剃
须刀上拔出微型 USB 插头。
2 让剃须刀运行直到停止，拧下剃须
刀背部的螺钉。 (图 25)
6 将剃须刀头组件重新安装到剃须刀
上。 (图 13)
每两个月：清洁剃须刀头
注意： 请勿使用清洁剂或酒精来清洁
剃须刀头。只能使用飞利浦清洁喷雾剂
(HQ110)。
1 关闭剃须刀电源，从电源插座上拔
下适配器，并从剃须刀上拔下小插
头。
2 按释放按钮 (1)，垂直向上移动剃须
刀头部件，将其从剃须刀 (2) 中拉
出。 (图 10)
3 逆时针转动橙色轮轴 (1) 并取下固
定架 (2)。 (图 14)
4 一次取下并清洁一个剃须刀头。每
个剃须刀头包含一组刀片和网罩。
(图 15)
注意： 不要同时清洁多组刀片和网罩，
因为它们都是相互匹配的。如果不小心
将刀片和网罩弄混，则需要数周时间才
能恢复产品的最佳剃须性能。
5 从刀片上卸下网罩。 (图 16)
6 用清洁刷的短毛一侧清洁刀片。按
箭头方向小心地清洁。 (图 17)
7 用清洁刷的长毛一侧清洁网罩。
(图 18)
8 清洁后，将刀片重新装回至网罩。
(图 19)
9 将剃须刀头重新放入剃须刀头部
件。 (图 20)
10 将固定架放回剃须刀头部件内 (1)，
并沿顺时针方向转动橙色轴轮 (2)
。 (图 21)
11 将剃须刀头组件重新安装到剃须刀
上。 (图 13)
存储
保持器具干燥。
必须在 5°C 至 35°C 之间的温度下使
用和存放本产品。
1 关闭剃须刀。
2 使用后请盖上剃须刀保护盖，以防
止损坏剃须刀头并避免其内积聚灰
尘。 (图 8)
注意： 确保保护盖的凸缘盖住释放钮。
3 请将剃须刀放入存储袋（仅限于
PQ288）。
问题 可能的原因 解决方法
剃须刀头已
损坏或磨
损。
更换剃须刀
头。见“更
换”一章。
按下开/
关钮
时，剃
须刀不
工作。
充电电池的
电量已耗
尽。
给电池充
电。见“充
电”一章。
我在剃
须后出
现皮肤
过敏。
您的皮肤需
要一定的时
间来适应飞
利浦剃须
刀。
在前 2-3 周
的使用过程
中，可能会
出现皮肤过
敏。在此之
后，皮肤过
敏通常会消
失。
剃须刀
头的转
速比平
时慢。
剃须刀头中
积聚了太多
的灰尘。
清洁剃须刀
头。请参
阅“清洁和
保养”一
章。
充电电池的
电量不足。
给电池充
电。见“充
电”一章。
产品发
出奇怪
的噪
音。
剃须刀头中
积聚了太多
的灰尘。
清洁剃须刀
头。清洁
后，用飞利
浦清洁喷雾
剂 (HQ110)
润滑网罩内
侧的中央
点。请参
阅“清洁和
保养”一
章。
剃须刀头已
损坏或磨
损。
更换剃须刀
头。见“更
换”一章。
3 使用螺丝刀卸下剃须刀的背部面
板。
4 卸下充电电池。
取出电池之后，不要再将剃须刀与电源
连接在一起。
保修与服务
如果您需要服务或信息，或者有任何疑
问，请访问飞利浦网站：www.philips.
com/support。您也可与您所在国家/地
区的飞利浦客户服务中心联系（可从全
球保修卡中找到其电话号码）。如果您
所在的国家/地区没有飞利浦客户服务中
心，请与当地的飞利浦经销商联系。
保修条款
由于剃须刀头（刀片和网罩）属于易磨
损物品，因此不在国际保修条款的涵盖
范围之列。
故障种类和处理方法
本章归纳了使用本产品时最常见的一些
问题。如果您无法根据以下信息解决问
题，请访问 www.philips.com/support
查阅常见问题列表，或联系您所在国家/
地区的客户服务中心。
问题 可能的原因 解决方法
剃须刀
的剃须
效果没
有以前
好。
剃须刀头变
脏。您没有
将剃须刀清
洁干净，或
长时间未清
洁过剃须
刀。
先彻底清洁
剃须刀头，
再继续剃
须。请参
阅“清洁和
维护”一
章。
过长的胡须
堵塞了剃须
刀头。
用随附的清
洁刷清洁刀
片和网罩。
见“清洁和
保养”中“
每两个月：
剃须刀头”
部分。
您清洁后将
刀片和网罩
装回固定架
时弄混了刀
片和网罩。
您将刀片放
到了其他网
罩中。如果
您不调换刀
片，可能要
花 2 至 3 周
的时间才能
恢复最佳剃
须状态。
03/08/2012