Philips QC5390 User manual

Register your product and get support at
www.philips.com/welcome
User manual
QC5390

3-22 mm 23-42 mm
QC5380/80QC530/80
1

6
Introduction
Congratulations on your purchase and welcome to Philips! To fully
benet from the support that Philips offers, register your product at
www.philips.com/welcome.
General description (Fig. 1)
1 Cutting element
2 On/off button
3 Zoom wheel
4 Handle
5 Charging light
6 Socket for appliance plug
7 Small comb
8 Large comb
9 Barber comb (QC5390/80 only)
10 Scissors (QC5390/80 only)
11 Adapter
12 Appliance plug
13 Pouch (QC5390/80 only)
14 Cleaning brush
Preparing for use
Note:You can also use the appliance directly from the mains when the battery
is empty.
Charging
Charge the appliance for at least 1 hour before you use it for the rst
time and after a long period of non-use.
When the appliance is fully charged, it has a cordless operating time of
up to 60 minutes.
When the charging light lights up orange, the battery is running low
(approx. 10 minutes of operating time left) and you need to recharge
the appliance.
1 Make sure the appliance is switched off.
2 Insert the appliance plug into the socket of the appliance and put the
adapter in the wall socket.
,The charging light starts ashing green to indicate that the appliance
is charging.
,When the batteries are fully charged, the charging light lights up
green continuously. After 30 minutes the charging light goes out to
save energy.
ENGLISH

Using the appliance
Clipping with comb
The appliance comes with 2 combs for different hair lengths.
The hair length settings are indicated in millimetres on the comb.
The settings correspond to the remaining hair length after clipping.
1 Select the comb you want to use.
The small comb cuts the hair to a length of 3mm to 22mm.
The large comb cuts the hair to a length of 23mm to 42mm.
2 Slide the comb straight into the guiding grooves on both sides of
the handle (‘click’).
3 To set the comb to the desired setting, turn te zoom wheel to
the desired hair length setting.
,The display on front of the appliance shows the selected hair length
in millimetres after cutting.
,After 8 minutes, the display goes out to save energy.To activate
the display again, turn the zoom wheel or press the on/off button.
Tip:Write down the hair length settings you selected to create a certain
hairstyle as a reminder for future clipping sessions.
4 Press the on/off button to switch on the appliance.
5 Move the appliance through the hair slowly.
Tips
- To clip most effectively, move the appliance against the hair
growth direction.
- Since all hair does not grow in the same direction, you need to move
the appliance in different directions (upwards, downwards and across).
- Make sure that the at part of the comb is always fully in contact
with the scalp to obtain an even result.
- Make overlapping passes over the head to ensure that you cut all
the hair that needs to be cut.
6 Regularly remove cut hair from the comb.
If a lot of hair has accumulated in the comb, remove the comb from
the appliance and blow and/or shake the hair out of it.
42
39
36
ENGLISH 7

Contouring without comb
You can use the appliance without comb to clip hair very close to the skin
(0.5mm) or to contour the neckline and the area around the ears.
Be careful when you clip without comb because the cutting
element removes every hair it touches.
1 Pull the comb off the appliance.
2 Before you start to contour the hairline around the ears, comb the
hair ends over the ears.
3 Press the on/off button to switch on the appliance.
4 Tilt the appliance in such a way that only one edge of the cutting
element touches the hair ends when you shape the contours around
the ears.
Only cut the hair ends.The hairline should be close to the ear.
5 To contour the neckline and sideburns, turn the appliance and make
downward strokes.
Move the appliance slowly and smoothly. Follow the natural hairline.
ENGLISH8

Cleaning
Clean the appliance every time you have used it with the cleaning brush
and with warm water (max. 40°C).
Never use compressed air, scouring pads, abrasive cleaning agents or
aggressive liquids such as petrol, acetone or ethereal oils to clean the
appliance.
Note:The appliance does not need any lubrication.
1 Switch off the appliance and disconnect it from the mains.
2 Remove the comb from the appliance and clean it with the
cleaning brush.
3 Brush the outside of the shaving unit.
4 Push the centre top end of the cutting element upwards with your
thumb until it opens.
5 Use the cleaning brush to remove the cut hair.
6 Clean the appliance under a warm running tap.
ENGLISH 9