Philips 8500 User manual

8500 series
EN User manual SC 用户手册
Please read this instructions carefully
before using the appliance.
使用产品前请仔细阅读本使用说明书。
Please keep this instruction book for future reference.
保留备用。

2www.philips.com/welcome
3
4
5
6
6
7
8
9
10
10
11
11
12
13
13
14
14
15
15
16
17

3
www.philips.com/welcome

4www.philips.com/welcome

5
www.philips.com/welcome
12 2
1
11
10
8
9
7
3
2
3
1
1
2
1
2
2
3
1
4
1
2
6
3
5
12

6www.philips.com/welcome
3
1
3
2
3
3
1
3
2
4

7
www.philips.com/welcome
4
6
7
5
3
9
8
3
1
2

8www.philips.com/welcome
EN The appliance is suitable to be used with tap water. However, if you live in an area
with hard water, we recommend that you mix an equal amount of tap water with
distilled or demineralized water. This will prevent fast scale build up and prolong
the lifetime of the appliance.
SC 本产品可使用自来水。但如果您居住的区域水质较硬，我们建议您将等量的自来水
与蒸馏水或软化水混合使用。这样可以防止水垢快速积聚，从而延长产品的使用
寿命。
2
1
3
2
1

9
www.philips.com/welcome
3
1
2
~90 秒
EN Press steam trigger for 10s before ironing to prevent water stains on garment.
SC 熨烫前，按下蒸汽开关 10 秒钟，防止在衣物上产生水渍。

10 www.philips.com/welcome
2
按两次
蒸汽持续 8 分钟
按一次
1
EN Press steam trigger twice quickly for continuous steam.
SC 快速按下蒸汽开关两次，即可连续喷出蒸汽。
1
按两次
按住
2 秒
蒸汽
持续
3 秒

11
www.philips.com/welcome
2
4
5
6
1 3

12 www.philips.com/welcome

13
www.philips.com/welcome

14 www.philips.com/welcome
4-3
4-1
4-2
1
2
1
2
3
2
10 分钟
1
10 分钟

15
www.philips.com/welcome
1
2
3
60 分钟
4
3
5
6
2
3
1

16 www.philips.com/welcome
1
2
2
1
3
2
1
7
4
6
5
10
2
1
8
2
1
9
1
2

17
www.philips.com/welcome
EN If you have any problems, visit www.philips.com/support for a list of frequently
asked questions or contact the Consumer Care Center in your country.
Problem Possible cause Solution
The appliance produces no
steam.
The steamer has not heated
up suciently (power button
ashes).
Let the appliance heat up for 90 seconds.
When the appliance is ready for use, the
light turns steady.
Auto shut-o has been activated
when the appliance has not
been used for more than
10minutes (powerbutton
ashes).
Press the power button and wait for
90seconds for the appliance to heat up
again.
Steam trigger has not been
pressed to emit steam.
Press the steam trigger to activate steam.
Low water level in the tank or
the tank is not inserted properly.
Rell the water tank and insert it
properly.
Steam lock has been activated
for 8 minutes.
Steam lock feature comes with
automatic release function. Double
tap on the steam trigger again for
continuous steam (refer to ).
Water leaks out from the
steamer base.
The water tank is not inserted
properly.
Insert the tank properly.
Water tank has been overlled. Fill water up to its MAX marking.
Steam lock cannot be
activated.
Fail to enter steam lock function. Double tap to activate the steam lock
function (refer to ).
Steam does not stop
automatically after placing
the steamer head onto the
holder.
Steam lock function is activated. Press once to deactivate steam lock
(refer to ).
The board cover becomes
wet or there are water
droplets on the garment
during steaming.
Steam has condensed on
the board cover after a long
steaming session.
Leave it to dry before storage. Replace
the board cover if it has worn out.
Purchase a new board cover from a
Philips Authorized Service Center.
Board is shaky during use. The pole is not secured to the
base of the product.
Make sure the last lever at the bottom
is locked.
The board is not secured onto
the pole.
Insert the two board clips fully until you
hear a “click” sound.

18 www.philips.com/welcome
Problem Possible cause Solution
Board cannot be tilted
or used in the horizontal
position.
The board tilting lever has not
been released.
Ensure the tilting lever is unlocked to
allow board to be tilted to a desired
position.
Once a desired position is attained, lock
the tilting lever to secure board.
( refer to /  )
Water droplets drip
from the steamer head,
sometimes the appliance
produces a croaking sound.
Steam condenses into water
in the hose and aect smooth
steam ow.
Lift the steamer head to straighten the
hose vertically.
At the start of a steaming session, set
the steam setting to be in MAX mode.
Hold the steamer head away from the
garment and press the steam trigger for
10 seconds to release the initial gush of
water droplets.
White akes come out of
the steamer head within
rst few usage sessions.
This is normal as the appliance
has gone through quality
tests and may have some
residualparticles.
Simply shake/ brush the akeso the
garment. Do not use wet cloth.
Dirty water, brown stains
or white akes come out of
the steamer head and stain
the garment.
Chemical or additives is added
into the water tank.
Never use chemical or additives with the
appliance. Fill the water tank with water
and allow it to steam out 1 full tank to
rinse o chemical residues.
For stain on garment, rinse o any stains
under running water.
For stain on steamer head, wipe any
deposits o the steamer head with a
damp cloth.
Depending on where you stay,
the water hardness level may
be high and results in fast scale
builds up.
Ensure that water tank is emptied after a
steaming session. It is recommended to
use a combination of demineralization/
distilled water (50%) mixed with tap
water (50%).
At the start of a steaming session, set
the steam setting to be in MAX mode.
Hold the steamer head away from the
garment and press the steam trigger for
10 seconds to release the initial gush of
water droplets.
For stain on garment, rinse o any stains
under running water.
For stain on steamer head, wipe any
deposits o the steamer head with a
damp cloth.

19
www.philips.com/welcome
问题 可能的原因 解决方法
产品无法产生
蒸汽。
蒸汽挂烫机未充分加热
（电源开关闪烁）。
让产品加热 90 秒钟。当产品可供使
用时，指示灯将持久亮起。
超过 10 分钟未使用产品
时，自动关熄功能启动
（电源按钮闪烁）。
按下电源开关并等待 90 秒钟，让产
品重新加热。
未按下蒸汽开关，无法释放
蒸汽。
按下蒸汽开关以激活蒸汽功能。
水箱中的水位低或水箱未正
确插入。
为水箱加水并正确装入。
蒸汽锁已激活 8 分钟。 蒸汽锁闭功能带有自动释放功能。
再次双击蒸汽开关以释放持久蒸汽
（请参阅 ）。
蒸汽挂烫机底座
漏水。
水箱没有正确地插入。 请正确插入水箱。
水箱加注过量。 将水加至 MAX（最多）标记处。
无法激活蒸汽锁。 未能进入蒸汽锁闭功能。 双击以激活蒸汽锁闭功能
（请参阅 ）。
将蒸汽喷头放在支
架上后，蒸汽不会
自动停止。
蒸汽锁闭功能已激活。 按下一次可停用蒸汽锁
（请参阅 ）。
熨衣板罩变湿或在
熨烫过程中衣物上
出现水滴。
长时间熨烫操作后，蒸汽会
冷凝在熨衣板罩上。
存放前请将其晾干。如果熨衣板罩
已破损，请将其更换。请从飞利浦
授权服务中心购买新的熨衣板罩。
Problem Possible cause Solution
When ironing at the
horizontal position, the
location of the iron dock
(where you rest the iron
on) is interfering with my
ironing.
The iron dock is located at the
side of the board instead of the
top of the board.
Change the location of the iron dock
to the top of the board when ironing
horizontally. Refer to .
The board is too high for
me at horizontal position.
Pole height is not adjusted
when changing from vertical/tilt
position to horizontal position.
Lower the pole height when ironing
horizontally. Refer to .
SC 如果您有任何问题，请访问 www.philips.com/support 查阅常见问题列表，或联
系您所在国家/地区的客户服务中心。

20 www.philips.com/welcome
问题 可能的原因 解决方法
熨衣板在使用过程
中摇晃。
伸缩杆未固定到产品底
座上。
请确保锁紧底部最后一节撑杆。
熨衣板未固定到伸缩杆上。 将两片熨衣板完全插入，直至听到
“咔哒” 一声。
熨衣板无法
倾斜或在
水平位置
使用。
未松开可倾斜杆。 确保将倾斜杆解锁，以便熨衣板倾
斜到所需的位置。
达到所需的位置后，请将倾斜杆锁
止以固定熨衣板。
（请参阅 /  ）
水滴从蒸汽喷头上
滴下，有时产品会
发出咕噜声。
蒸汽在输送管内凝结成水，
影响蒸汽流的平稳畅通。
提起蒸汽喷头以垂直拉直蒸汽输
送管。
在开始蒸汽熨烫时，请将蒸汽设置
为MAX（强力）模式。将蒸汽喷头
远离衣物，按住蒸汽开关 10 秒钟，
以释放初始涌出的水滴。
在前几次熨烫期
间，蒸汽喷头出现
白色水垢。
这属于正常现象，因为产品
经过质量检测，可能存在些
许残余颗粒。
只需抖落/掸去衣物上的水垢即可。
请勿使用湿布。
蒸汽喷头出现脏
水、褐色污渍或白
色水垢，在衣物上
留下污渍。
在水箱中添加了化学品或添
加剂。
切勿在产品中使用化学品或添加
剂。向水箱中注入水，让 1 满水箱
的水通过生成蒸汽排出，以冲洗掉
化学残留物。
对于在衣物上留下的污渍，请在自
来水下冲洗掉所有污渍。
对于蒸汽喷头上的污渍，请用湿布
擦去蒸汽喷头上的所有沉积物。