Philips Azur GC4233 User manual

Azur
GC4243, GC4238, GC4233, GC4223, GC4218

2

ENGLISH 4
ESPAÑOL 12
PORTUGUÊS 20
ITALIANO 28
 36
TÜRKÇE 45
GC4243, GC4238, GC4233, GC4223, GC4218
3

Important
Read these instructions for use carefully before using the appliance and
save them for future reference.
- Never leave the iron unattended when it is connected to the mains.
- This appliance is not intended for use by children.
- Infirm persons should not be allowed to use the appliance without
supervision. Keep an eye on children to make sure that they do not
play with the appliance.
- The soleplate of the iron can become extremely hot and may cause
burns if touched.
- Never use the appliance if it is damaged in any way.
- When you have finished ironing, when you clean the appliance, when
you fill or empty the water tank and also when you leave the iron
even for a short while: set the steam control to position O, put the
iron on its heel and remove the plug from the wall socket.
- If the mains cord is damaged, it must be replaced by Philips, a service
centre authorised by Philips or similarly qualified persons in order to
avoid a hazard.
Before first use
1Check if the voltage indicated on the appliance corresponds to
the local mains voltage before you connect the appliance.
C2Remove the protective heat cover from the soleplate (type
GC4243 only). Remove any sticker or protective foil from the
soleplate.
3Let the iron heat up to maximum temperature and pass the
iron over a piece of damp cloth for several minutes to remove
any residues from the soleplate.
BThe iron may give off some smoke when you use it for the first time.This
will cease after a short while.
Preparing for use
Filling the water tank
Never immerse the iron in water.
1Remove the mains plug from the wall socket.
C2Set the steam control to position O (= no steam).
3Open the cap of the filling opening.
4Tilt the iron backwards.
ENGLISH4

C5Fill the water tank with tap water up to the maximum level by
means of the filling cup.
Do not fill the tank beyond the MAX indication.
◗If the tap water in your area is very hard, we advise you to mix it
with an equal amount of distilled water or to use distilled water
only.
Do not put additives, vinegar, starch or chemically descaled water in the
water tank.
C6Close the cap of the filling opening.You will hear a click.
Setting the temperature
C1Type GC4243 only: remove the protective heat cover.
Do not leave the protective heat cover on the soleplate during ironing.
2Put the iron on its heel.
C3Set the temperature dial to the required ironing temperature
by turning it to the appropriate position.
- Check the garment label for the required ironing temperature.
-1Synthetic fabrics (e.g. acrylic, nylon, polyamide, polyester)
-1Silk
-2Wool
-3Cotton, linen
- If you do not know what kind(s) of fabric(s) an article is made of,
determine the right ironing temperature by ironing a part that will
not be visible when you wear or use the article.
- Silk, woollen and synthetic materials: iron the reverse side of the
fabric to prevent shiny patches. Avoid using the spray function to
prevent stains.
- Start ironing the articles that require the lowest ironing temperature,
such as those made of synthetic fibres.
4Put the mains plug in an earthed wall socket.
ENGLISH 5
N
Y
L
O
N
S
O
I
E
L
A
I
N
E
C
O
T
O
N
L
I
N
N
Y
L
O
N
S
I
L
K
W
O
O
L
C
O
T
T
O
N
L
I
N
E
N

C5When the amber temperature pilot light has gone out, wait a
while before you start ironing.
The amber pilot light will go on from time to time during ironing.
Using the appliance
Steam ironing
1Make sure that there is enough water in the water tank.
C1Select the appropriate steam setting. Make sure that the steam
setting you select is suitable for the ironing temperature
selected:
- 1 - 3 for moderate steam (temperature settings 2to 3)
- 4 - 6 for maximum steam (temperature settings 3to MAX)
See 'Setting the temperature'.
BThe iron will start producing steam as soon as the set temperature has
been reached.
Ironing without steam
C1Set the steam control to position O (= no steam).
2Select the recommended ironing temperature.
See 'Setting the temperature'.
Features
Spraying
You can use the spray function to remove stubborn creases at any
temperature.
Make sure that there is enough water in the water tank.
C1Press the spray button several times to moisten the article to
be ironed.
ENGLISH6

Shot of steam
A powerful 'shot' of steam helps remove stubborn creases.
The shot-of-steam function can only be used at temperature settings
between 2and MAX.
C1Press and release the shot-of-steam button.
Drip stop
This iron is equipped with a drip-stop function: the iron automatically
stops producing steam when the temperature is too low to prevent
water from dripping out of the soleplate.When this happens you may
hear a sound.
Vertical shot of steam
C1The shot-of-steam function can also be used when you hold
the iron in vertical position.
Never direct the steam at people.
Automatic anti-calc function
C1The built-in anti-calc system reduces the build-up of scale and
guarantees a longer life for the iron.
ENGLISH 7

Electronic safety shut-off function (types GC4243, GC4238
and GC4233 only)
C1The electronic safety shut-off function automatically switches
off the iron if it has not been moved for a while.
◗The red auto-off pilot light starts blinking to indicate that the iron
has been switched off by the safety shut-off function.
To let the iron heat up again:
- Pick up the iron or move it slightly.
- The red auto-off pilot light goes out. If the temperature of the
soleplate has dropped below the set ironing temperature, the amber
temperature pilot light goes on.
- If the amber pilot light goes on after you have moved the iron, wait
for it to go out before you start ironing.
- If the amber pilot light does not go on after you move the iron, the
soleplate still has the right temperature and the iron is ready for use.
Alert light
C◗Types GC4243 and GC4238 only:
- The iron is equipped with a blue alert pilot light.
- The blue alert light burns as long as the iron is plugged in, even if the
iron has been switched off by the safety shut-off function.
Cleaning and maintenance
Using the calc-clean function
You can use the calc-clean function to remove scale and impurities.
◗Use the calc-clean function once every two weeks. If the water in
your area is very hard (i.e. when flakes come out from the
soleplate during ironing), the calc-clean function should be used
more frequently.
1Set the steam control to position O.
2Fill the water tank to the maximum level.
ENGLISH8

Do not put vinegar or other descaling agents in the water tank.
C3Select the maximum ironing temperature.
4Put the plug in the wall socket.
5Unplug the iron when the amber temperature pilot light has
gone out.
C6Hold the iron over the sink, press and hold the calc-clean
button and gently shake the iron to and fro.
BSteam and boiling water will come out of the soleplate. Impurities and
flakes (if any) will be flushed out.
7Release the calc-clean button as soon as all the water in the
tank has been used up.
Repeat the calc-clean process if the iron still contains a lot of impurities.
After the calc-clean process
- Put the plug in the wall socket and let the iron heat up to allow the
soleplate to dry.
- Unplug the iron when it has reached the set ironing temperature.
- Move the hot iron gently over a piece of used cloth to remove any
water stains that may have formed on the soleplate.
- Let the iron cool down before you store it.
After ironing
1Remove the mains plug from the wall socket and let the iron
cool down.
2Wipe flakes and any other deposits off the soleplate with a
damp cloth and a non-abrasive (liquid) cleaning agent.
3Clean the upper part of the iron with a damp cloth.
C4Regularly rinse the water tank with water. Empty the water
tank after cleaning.
ENGLISH 9
N
Y
L
O
N
S
O
I
E
L
A
I
N
E
C
O
T
O
N
L
I
N
N
Y
L
O
N
S
I
L
K
W
O
O
L
C
O
T
T
O
N
L
I
N
E
N

Storage
1Remove the mains plug from the wall socket and set the steam
control to position O.
2Empty the water tank.
C3a) Let the iron cool down.Wind the mains cord around the
cord storage facility and fix it with the cord clip.
b) Always store the emptied iron horizontally on a stable surface and
use a cloth to protect the soleplate.
C4Protective heat cover (types GC4243 only)
a) Put the iron on the protective heat cover.
Do not use the protective heat cover during ironing.
b) Wind the mains cord around the cord storage facility.
c) Store the iron with the protective heat cover horizontally on a stable
surface.
Guarantee & service
If you need information or if you have a problem, please visit the Philips
Web site at www.philips.com or contact the Philips Customer Care
Centre in your country (you will find its phone number in the
worldwide guarantee leaflet). If there is no Customer Care Centre in
your country, turn to your local Philips dealer or contact the Service
Department of Philips Domestic Appliances and Personal Care BV.
Troubleshooting
This chapter summarises the most common problems you could
encounter with your iron. Please read the different sections for more
details. If you are unable to solve the problem, please contact the
Customer Care Centre in your country.
ENGLISH10