Philips ELANCE GC3006 User manual

ServiceManual
Philips Domestic Appliances and Personal Care
Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification
Steam Iron Elance
GC 3006
PRODUCT INFORMATION
Features
- Colour classic blue
- Careeza soleplate
- Tank capacity (300ml)
- Steam rate (30 g/min)
- Shot of steam (75 g/min)
- Integrated cord winder
- Cord length : 2 m.
4322 277 00716
02/03
This product meets the requirement regarding
interference suppression on radio and television.
TECHNICAL INFORMATION
Voltage : 220 - 240 V
Frequency : 50 - 60 Hz
Power consumption : 1800 W
Water advice : Suitable for tap water use. However if
the tap water in your area is very hard,
we advise you to mix it with a equal
portion of distilled water or to use
distilled water only.
Cleaning of the Iron : Use only the Calc clean button for
cleaning of the Iron.
Never use vinegar, starch or chemically
descaled water.
Soleplate
Careeza is a multi layer chemical substance that gives an excellent
gliding over various fabrics and better care for the garments.

DISASSEMBLY ADVICE IRON
DIAL 1
BACKPLATE 2
CORD SET 3
SWIVEL 4
Remove Screw A (1x)
Remove BACKPLATE 2
Remove Screw B (2x)
cord clamping
INLAY 5
LAMP ASSY 6
FILLING DOOR 7
STEAM SLIDER 8
LAMP COVER 9
SOS KNOB 10
SPRAY KNOB 11
TANK SEAL 12
remove Screw A (1x)
remove BACKPLATE 2
remove Screw B (2x)
cord clamping
remove INLAY 5
DOSING UNIT 13
remove Screw A (1x)
remove BACKPLATE 2
remove Screw B (2x)
cord clamping
remove INLAY 5
remove Screw C (2x)
remove Screw D (2x)
remove DOSING UNIT 13
HANDLE 14
RATTLE SPRING 15
PUMP 16
remove Screw A (1x)
remove BACKPLATE 2
remove Screw B (2x)
cord clamping
remove INLAY 5
remove Screw C (2x)
remove Screw D (2x)
remove DOSING UNIT 13
remove Screw E (2x)
remove HANDLE 14
TANK 17
THERMOSTAT
BUSH 18
remove Screw A (1x)
remove BACKPLATE 2
remove Screw B (2x)
cord clamping
remove INLAY 5
remove Screw C (2x)
remove Screw D (2x)
remove DOSING UNIT 13
remove Screw E (2x)
remove HANDLE 14
remove Screw F (2x)
remove TANK 17
SHIELD 19
remove Screw A (1x)
remove BACKPLATE 2
remove Screw B (2x)
cord clamping
remove INLAY 5
remove Screw C (2x)
remove Screw D (2x)
remove DOSING UNIT 13
remove Screw E (2x)
remove HANDLE 14
remove Screw F (2x)
remove TANK 17
remove Screw G (1x)
remove SHIELD 19
COVER 20
SOS SEAL 21
DOSING SEAL 22
SOLEPLATE ASSY 23
remove Screw A (1x)
remove BACKPLATE 2
remove Screw B (2x)
cord clamping
remove INLAY 5
remove Screw C (2x)
remove Screw D (2x)
remove DOSING UNIT 13
remove Screw E (2x)
remove HANDLE 14
remove Screw F (2x)
remove TANK 17
remove Screw G (1x)
remove SHIELD 19
remove Screw H (2x)
remove COVER 20

PARTS LIST IRON
Screws : d x 1
A, B 3.5 x 16 mm
C2.5 x 14 mm
D3.5 x 15 mm
E3.5 x 17 mm (with washer 1mm)
F4.0 x 12 mm (with washer 1mm)
G4.0 x 10 mm
Pos Description Service code
1.
2.
3.
4.
5.
Dial (Ger/Swe)
Backplate
Cordset (Europe)
Swivel
Inlay
4239 021 11880
4239 022 53110
4239 000 07970
4239 025 92070
4239 021 07280
6.
7.
8.
9.
10.
Lamp assy
Filling door assy
Steam slider
Lamp cover
SOS knob
4239 021 03140
4239 021 10050
4239 026 10150
4239 026 08280
4239 026 10030
11.
12.
13.
14.
15.
Spray knob
Tank seal
Dosing unit
Handle
Rattle spring
4239 026 10080
4239 015 54400
4239 021 08510
4239 026 08050
4239 026 08840
16.
17.
18.
19.
20.
Pump
Tank Assy (non Drip stop)
Thermostat bush
Heat shield
Cover (non Drip stop)
4239 020 90560
4239 022 53200
4239 015 98410B
4239 010 07850
4239 026 09750
21.
22.
23.
24.
SOS seal
Dosing seal
Soleplate assy 230 V / 1800 W
Lamp holder
4239 015 51450
4239 015 54660
4239 022 53180
4239 026 01220
RESISTOR
LAMP
FUSE
N
L
E
HEATING
UNIT
INPUT
THERMOSTAT

EXPLODED VIEW IRON

IMPORTANT + ADJUSTMENT AND CONTROLS
IMPORTANT
Due to high voltage of the iron, only the specified cord sets must be used.
NOTES :
1) For standardisation reasons :
Type plate : No info. about the typenumber and voltage have been stamped onto the typeplate.
When replacing the typeplate, engrave at least typenumber onto the typeplate with a sharp object.
2) After the product had been repaired, it should function properly and has to meet the safety requirements and
legal regulations as laid down and officially established at this moment.
ADJUSTMENTS AND CONTROLS
Thermostat
Thermostat, fitted to the soleplate 23 has already been adjusted by the supplier and secured by glue.
To avoid mal-function of the iron, NEVER re-adjust the thermostat.
NOTE : the thermostat can only be ordered together with the soleplate assembly 23.