Philips SpeedCare GC6625 User manual

Published by Philips Consumer Lifestyle Printed in the Netherlands © Copyright reserved Subject to modification
ServiceManual
Philips Consumer Lifestyle
SpeedCare Steam Generator
GC6625
14/05
Product information
Fast & powerful crease removal
•Soleplate: Ceramic soleplate
•Vertical steam
•Steam pressure: . bar
•Power:  W
•Steam boost:  g
•Continuous steam output:  g/min
Easy to use
•Water tank capacity:  ml
•Filling and emptying water: Extra large filling hole
•Refill any time
•Heatup time:  min
•Storage solution: Carry lock
•Hose storage: Hose storage compartment
•Cord freedom (swivel):  degree cord freedom
•Hose length: . m
•Power cord length: . m
Calc management
•Suitable for tap water
•Calc clean solution: Smart Calc Clean
•Calc clean reminder
•Filtered water recommended
Safety Information
•This product meets the requirements regarding
interference suppression on radio and TV.
•After the product has been repaired, it should function
properly and has to meet the safety requirements and
legal regulations as officially laid down at this moment.
Technical information
•Weight of iron : . kg
•Weight of iron  base : . kg
•Product dimensions : . x . x . cm
•Packaging dimensions : . x . x . cm
•Voltage :    V
•Frequency :    Hz
•Power :  W

2-7
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Remove
Fig 1: Thermistor is part of the Power PBCA Asm

GC6625
3-7
Disassembly advice - Stand
SCREW CAP 57
SILICON CUSHION 56
INSULATION BASE 55
UNIT BASE COVER 51
BOTTOM FOOT 40
WATER TANK ASM 36
UNIT BASE BODY 43
Remove SCREW CAP 57
Remove Screws A1, A2
Remove SILICON CUSHION 56
Remove INSULATION BASE 55
Remove Screws C1, C2, C3, C4, C5, C6, C7
Remove UNIT BASE COVER 51
Remove BOTTOM FOOT 40
Remove Screws D1, D2, D3, D4, D5, D6, D7
Remove WATER TANK ASM 36
Remove UNIT BASE BODY 43
PUMP BRACKET 41, 44
PUMP ASSY 42
CORD CLAMP 45
CORD BOX COVER 50
TERMINAL BLOCK 46
SWITCH BRAKET & ROCKER SWITCH 47
POWER CORD ASM 52
Remove SCREW CAP 57
Remove Screws A1, A2
Remove SILICON CUSHION 56
Remove INSULATION BASE 55
Remove Screws C1, C2, C3, C4, C5, C6, C7
Remove UNIT BASE COVER 51
Remove BOTTOM FOOT 40
Remove Screws D1, D2, D3, D4, D5, D6, D7
Remove WATER TANK ASM 36
Remove UNIT BASE BODY 43
Remove Screw E1, E2
Remove PUMP BRACKETS 41, 44
Remove PUMP ASSY 42
Remove Screw F1, F2, F3, F4
Remove CORD CLAMP 45
Remove Screw G1
Remove CORD BOX COVER 50
Remove Screw H1
Remove TERMINAL BLOCK 46
Remove Screw I1, I2
Remove SWITCH BRACKET & ROCKER SWITCH 47
Remove POWER CORD ASM 52

4-7
Power cord
Hose cord
Power board
Dosing head
Soleplate
Thermistor
Control board
Fixed water tank
Stand Iron
Water pump
Pressure relief valve
(opens at 2 bar)
Potentiometer (connected to T-dial
to set soleplate’s temperature)
Pos Service code Description
Control PCB assy
Control PCB box
Lamp cover
Steam knob
Housing
Knob cylinder
Knob spring
Steam tube connector
Base
Thermal insulation pad
Soleplate assy
ber tube
Throat clamp
Bend connector
Throat clip
Potentiometer box
Cord clamp
Dial knob
Top cover
Cord bushing
Power PCB box
Power PCB asm
Silicon pad
Switch hole cover
Button
Connection wire asm
Wire connector
Iron base support
Pos Service code Description
Release button
Lock fastener
Location fastener
Bolt base
Water tank asm
Seal ring
Water tube connector
Silicon tube
Bottom foot
Pump assy
Unit base body
Cord clamp
Terminal block
Switch bracket & Rocker switch
Safety valve asm
Silicon tube
Cord box cover
Unit base cover
Insulation base
Screw cap
Calc clean container & sticker
73639
73641

5-7
A2
A1
E1
H1
H2
H3
H4
E2
C1
D1
F2
F1
G1
G3
B1
G2
16
12
25
2
6
7
26
9
11
5
27
13
28
8
1
3
18
21
20
10
24
4
22
15
23
14
17
19
59

GC6625
6-7
A2
C1 C2
C6
G1
H1
E1
D1
D2
D4
D5
D3
D6
D8
D7
E2
F1
F2
F4
F3
I1 I2
A1
C3
C5 C7
C4
38 42 44
34
35
36
43
37
41
33
32
31
57
52
55
45
50
49
47
40
46
39
58
51
48
56
Exploded view - Stand

7-7
•Due to the high wattage of the iron, only the cord set must be used.
•Should damage be observed on the , it must be replaced.
•Continued usage is not allowed.
•If is provided without type plate information eg. Type number, voltage etc. When replacing the cover,
engrave the type number & voltage on the type plate with a sharp object.
•After the product has been repaired, it should function properly and has to meet the safety requirements & legal regulation
as laid do ally established at this moment.
•The following tests are common checks that are conducted on a repaired product before it is returned to the consumer.
Check the soleplate temperature is within IEC requirement.
Soleplate temperature ( Deg C)
Materials, for example
Test-
point
= =
Minimum Maximum
Check that leakage current is within IEC requirement.
Measure leakage current between LIVE/NEUTRAL & EARTH.
Check that there is no water leakage from any part of product during operation.
Check that the functionality of the product (product dependent) eg. Steaming, steam trigger, variable steam, SOS, PCBA
etc is working properly.
Check that there are no loose parts eg. Extra screws in
When replacing fuse, to also service the water tubes which is probably choked with calc.
All failed PCBAs including to be packed with ESD bags for shipment.
ned screws in terms of length and material used.
Repair Instruction
The torque of the thermistor-soleplate screw is 9-12kg f.cm.
230170