Philips DTR2000/00 User manual

Doc.DTR2000 version N/B 19/12/03 9:01 Page 1

WELCOME TO DIGITAL TELEVISION
Congratulations on choosing the Philips DTR 2000 digital terrestrial receiver.
The DTR 2000 will allow you:
- To access to a wider variety of digital terrestrial television and radio channels,including Pay-TV(*).
- To benefit from digital video and audio quality.
- To easily access television channels via your aerial.
(*)To watch Pay-TV channels, you need to take out a subscription.
2
English
Doc.DTR2000 version N/B 19/12/03 9:01 Page 2

QUICK INSTALLATION
QUICK START UP
You already have an aerial.
Your aerial is correctly pointed at the terrestrial transmitter
corresponding to your area.
Your digital receiver connection is according to the diagram
depicted in chapter 5.1 or 5.2.
Your digital receiver is ON and the“WELCOME” screen is
displayed for a short time.Then the“First Installation” screen
is displayed.The selection is on“Language”.
- Select the desired language using the uor ibutton.
- Press the ybutton to move to“Country”.
- Select the desired country and press“OK”.
The next screen allows you to select theTV format.
- Press the uor ibutton to select the appropriateTV
format and press“OK”.
The receiver starts scanning for channels and reports
scanning progress and number of channels found.When
scanning is completed:
- Either scanning was performed successfully and the
number of channels found is displayed.You can start
watchingTV.
- Or scanning failed and the“Channel installation failed”
screen is displayed.If so proceed to chapter 6.2.
Note: If the first installation has already been performed
successfully but you want to set another country, use the
Reinstallation feature, available from the Setup menu.
English
QUICK INSTALLATION 3
Doc.DTR2000 version N/B 19/12/03 9:01 Page 3

4SCANNING FAILURE
English
SCANNING FAILURE
Scanning failed.Before starting a new scanning,check:
- the aerial cable,
- the aerial cable connection to your digital receiver. Refer
to the connection diagrams in chapter 5.1 or 5.2.
- channel(s) availability in the region corresponding to your
area.
To exit the“Channel installation”failure screen:
- Press“OK”.The“Signal quality testing”screen is displayed,
with bargraphs indicating the signal strength and quality.
- Select a channel number using the remote control
numerical keys and press“OK”.
If the signal is good enough (indicated by green bar meters),
press OK to launch a new scanning.When scanning ends
successfully, the channels found are displayed and the digital
receiver tunes the first channel in the list.If so proceed to
chapter 7.
Note: If you could still not install the channels after checking the
quality of the signal delivered by your aerial, either your aerial is
not pointing properly at the digital TV transmitter, or your aerial
installation needs to be upgraded, or you are not in the coverage
area to correctly receive digital television.
For a proper diagnosis, call your electrical retailer.
Doc.DTR2000 version N/B 19/12/03 9:01 Page 4

1Safety instructions 7
2Unpacking / installing the receiver
in your existing setup 8
2.1 Unpacking 8
2.2 Installing the receiver in your existing
setup 8
3Product description 9
3.1 Front view 9
3.2 Rear view 10
4Preparing your remote control 11
4.1 Inserting batteries 11
4.2 Using the remote control 12
5Connecting your digital receiver 13
5.1 Connecting to aTV using one SCART
socket. 13
5.2 Connecting to aTV andVCR both
fitted with SCART sockets 14
5.3 Connecting to your HiFi /Audio receiver
equipment.(Analogue / Digital) 15
5.4 Connecting of aVideo projector to
your receiver to watch DigitalTV
programmes on a video projector 15
6Day to day operation 16
6.1 Switch your receiver on/off (low
power, standby) 16
6.2 SelectTV or Radio service in running
mode 16
6.3 Change channels 16
6.3.1 Using number buttons 16
6.3.2 Using“P+”/“P-”buttons 16
6.3.3 Using the“BACK”button
(last channel recall) 16
6.3.4 Using channel lists
(Service selector) 17
6.4 Banner 17
6.5 Volume control -Vol+ /Vol- / Mute 18
6.6 Temporarily change the Subtitles
selection 18
6.7 Temporarily change theAudio
language selection 18
6.8 Guide (Event selector) 19
6.9 Recording timers 19
6.10 Using theTV/STB button 20
6.11 Watching locked channels 20
6.12 How do I reset my receiver 20
7Changing the settings of your
receiver 21
7.1 Menus and settings 21
7.2 “Setup”menu 21
7.2.1 Channels installation 22
7.2.1.1 Update 22
7.2.1.2 Custom update 22
7.2.1.3 Full reinstallation 22
7.2.1.4 Installation success/failure 22
7.2.2 TV/VCR configuration 23
7.2.2.1 TV Format 23
7.2.2.2 TV output signal 23
English
TABLE OF CONTENTS 5
TABLE OF CONTENTS
Doc.DTR2000 version N/B 19/12/03 9:01 Page 5

7.2.2.3 TV audio signal 23
7.2.2.4 VCR output signal 23
7.2.2.5 VCR recording control 24
7.2.3 Time Setting 24
7.2.4 Remote Control Setting 24
7.2.5 Reinstallation 25
7.3 Favourites lists 25
7.3.1 Create a Favourites list 25
7.3.2 Modify a Favourites list 25
7.3.2.1 Add/Skip a channel
(green button) 25
7.3.2.2 Lock/unlock a channel
(red button) 26
7.3.2.3 Sort/move a channel
(yellow button) 26
7.3.2.4 Skip/Add all channel
(blue button) 26
7.3.2.5 Saving confirmation popup 26
7.3.3 Delete a Favourites list 27
7.4 Timers 27
7.4.1 Add timer 27
7.4.2 Modify timer 28
7.4.3 Delete timer 28
7.4.4 SleepTimer 28
7.5 New channels 28
7.6 Subscription Settings 29
7.7 User preferences 29
7.7.1 Languages 29
7.7.2 Parental Control 29
7.7.3 Pin code change 30
7.8 System Information 27
8Menu tree 31
9More about recording
(VCR or DVD control) 32
9.1 Connection for Easy recording 32
9.2 Digital receiver andVCR or
DVD settings 33
9.3 Recording with theVCR control
feature 33
10 Troubleshooting guide
(references to be updated!!!) 34
11 Technical specifications 36
6TABLE OF CONTENTS
English
Doc.DTR2000 version N/B 19/12/03 9:01 Page 6

All the safety and operating Instructions should
be read and understood before using the
receiver.
For best results,position your receiver away
from radiators or other heat sources.Leave a
space of at least 3 cm around the receiver for
ventilation making sure that the ventilation
holes are not obstructed.
This receiver is intended for use in a domestic
environment only and should never be
operated or stored in excessively hot,humid
or damp conditions.
Make sure no objects or fluids enter the
housing through the ventilation slots.Should
this happen,disconnect your receiver from the
mains and consult your retailer.
To clean the receiver, use a damp chamois
leather. Never use an abrasive cloth,sponge or
cleaner.
When connecting or disconnecting cables to
the receiver always ensure the receiver is
disconnected from the mains.
Please wait before connecting your receiver -
read on.
Do not disassemble the equipment.There are
no user serviceable parts.
Mains connection
Before connecting the receiver to the mains,
check that the mains supply voltage
corresponds to the voltage printed on the rear
of the receiver. If the mains voltage is different,
consult your dealer.
Please wait before connecting your
receiver - read on.
English
SAFETY INSTRUCTIONS 7
1 Safety instructions
Doc.DTR2000 version N/B 19/12/03 9:01 Page 7

2.1 Unpacking
Start by unpacking your receiver.You will find
the following cables and accessories:
- The digital terrestrial receiver
- The remote control and batteries
(2 x LR6AA 1,5V)
- One SCART lead
- One RF coaxial lead
- A mains cord
- A user manual
- A Guarantee card
- A stand for using the receiver in the upright
position.
Note: As advised in chapter 5, use the SCART lead
provided. It has been selected to get the best
picture quality and performance out of your digital
receiver.
Plastic bags can be dangerous.To avoid
suffocation keep the bag away from babies and
children.
The symbol on the packaging means that
material is recyclable.
If the receiver will not be used for a long time,
unplug the mains cord from the wall socket.
2.2 Installing the receiver in
your existing set-up
Your receiver can be integrated in different
ways within your existingAudio-Video set up.
The receiver can be used in the horizontal or
vertical position.If you decide to use your
receiver in the upright position,follow the
instructions below:
- Unpack the stand,place it on a horizontal
surface with click fit side on the left and lug
side on the right.
- Position the receiver as shown below (rear
panel on the left side / coaxial connectors
on the bottom side).
- Insert the stand lug in the slot located on
the front of the receiver,close to the Philips
badge.
- Rock the receiver to insert the stand lug fully
in the slot until it is locked by the click fit.
From now on,your receiver can be used in the
upright position.
Note:To remove the stand, unlock the click fit at
the rear side of the stand, rocking and pulling back
the receiver to extract it from the stand lug.
8UNPACKING
English
2 Unpacking / Installing the receiver in your
existing set-up
Doc.DTR2000 version N/B 19/12/03 9:01 Page 8

Note: If you have put your receiver in “standby” or “low power” mode and the red, right-hand LED is blinking, it
indicates that a free over-the-air upgrade of your receiver is taking place. Do not interrupt this operation.Wait
until the LED stops blinking and the left-hand LED is either orange or red (signalling either “standby” or “low
power” mode).You can then continue as normal.
3.1 Front view
English
PRODUCT DESCRIPTION 9
3 Product description
1LOW POWER button: . . . . . . . . . . Switch receiver ON or to“low power”mode.
Reset the receiver after a 5 second key press.
2TV/RADIO button . . . . . . . . . . . . . . . Toggle betweenTV and Radio mode.
3“-”button . . . . . . . . . . . . . . . . . . . . . . . . Channel down.
4Multicolour LED indicator . . . . . . Display receiver status (see status indicator table).
5Red LED indicator . . . . . . . . . . . . . . . Display receiver status (see status indicator table).
Blink at remote control command reception.
6“+”button . . . . . . . . . . . . . . . . . . . . . . . . Channel up.
7Smart Card slot . . . . . . . . . . . . . . . . . . Insert the smart card with the chip facing up.
Status indicator table
LED Right-hand LED Left-hand LED
Mode (Green/Orange) (Red)
Receiver off mains
Low power mode Red
Standby mode Orange
TV/Radio mode Green
Timer mode from running mode Green Red
Timer mode from standby mode Orange Red
QW
ERTYU
Doc.DTR2000 version N/B 19/12/03 9:01 Page 9

10 PRODUCT DESCRIPTION
English
3.2 Rear view
1 VCR (*) . . . . . . . . . . . . . . . . . . . . . . . . . . SCART (1) socket to connect your video recorder
or DVD player/recorder
2 Digital audio output (*) . . . . . . . . Coaxial Digital audio output to connect your HIFI /
Audio receiver system
3 Serial (*) . . . . . . . . . . . . . . . . . . . . . . . . . RJ 9 socket for serial data transfer during servicing
4 AERIAL IN (*) . . . . . . . . . . . . . . . . . . . Input to connect your UHF aerial
5 230V~50Hz 10W max (**) . . . Socket to connect the Mains cord
6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Label showing the type and serial number of the receiver
7 TV (*) . . . . . . . . . . . . . . . . . . . . . . . . . . . . SCART (1) socket to connect to yourTV set or a video
projector (2)
8 L/RAudio out (*) . . . . . . . . . . . . . . . Left/Right audio outputs to connect your HIFI /
Audio receiver system
9 RF out (*) . . . . . . . . . . . . . . . . . . . . . . . . RF output to be connected to the aerial input of your video
recorder orTV set. Refer to chapter 5 for recommended
connection diagrams.
(1) SCART is also called Euroconnector or Peritel.
(2) To connect a video projector to the TV SCART socket, refer to chapter 5.4.
* Safety Extra Low Voltage (SELV)
** Hazardous Voltage (HV)
QWER
TY IO
U
Doc.DTR2000 version N/B 19/12/03 9:01 Page 10