Philips SRP2024R/27 User manual

7252
User manual
v1 5/19
Scan this code to
watch a video on how
to set up this remote
www.byjasco.com/remote
Audio/Video
SRP2024R/27

2
Install your Roku remote.............................................2
Setup..............................................................................3
Button Functions .........................................................4
Programming Your Remote ........................................6
Direct Code Entry...................................................6
Auto Code Search ..................................................8
Controlling Combo Devices ..................................9
Using Your Remote ....................................................10
Primary Audio Control.........................................10
Code Identication ...............................................11
Reset to Factory Settings ....................................11
Troubleshooting......................................................... 12
Warranty...................................................................... 13
FCC Statement ........................................................... 14
Table of Contents
Install your Roku remote
1 2 3
4
Remove the
two retaining
screws, then
carefully remove
the battery
compartment
cover
Install 2
AAA batteries,
noting correct
polarity
Replace the
battery cover
and reinstall the
two retaining
screws, and your
remote is ready
to use
Carefully slide
your Roku
remote into
the cradle
IMPORTANT:SAVE THIS MANUAL AND CODE
LIST FOR FUTURE REFERENCE
Compatible with streaming device remotes for Roku®
Express+, Premier, Premier+, Streaming Stick and
Streaming stick+ models only.

3
Setup
Your universal remote requires two (2) AAA
batteries (not included). Alkaline batteries are
recommended.
Battery Installation
1. On the back of the remote, remove the two
retaining screws at the bottom. Pull down on
the textured surface and slide battery cover
downward to remove.
2. Match the (+) and (-) marks on the batteries
to the (+) and (-) marks inside the battery
compartment, then insert two (2) AAA
batteries. Be sure to use fresh batteries.
3. Position battery cover slightly below opening
and push upward to lock into place. Reinstall
the two retaining screws.
NOTE:If your remote stops operating properly,
replace the batteries with new ones.
Battery Precautions
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc),
or rechargeable (Ni-Cd, Ni-MH, etc.) batteries.
• Always remove old, weak or worn-out batteries
promptly and recycle or dispose of them in
accordance with local and national regulations.
Battery Saver
Your remote automatically turns o if the buttons
are held down for more than 8 seconds. This will
save your batteries should your remote get stuck
in a place where the buttons remain depressed
(e.g., between sofa cushions).
Code Saver
You have up to 10 minutes to change the batteries
in your remote without losing the codes you have
programmed.

4
Button Functions
A
1 2 3
4 5 6
7
(-)
8
0
9
B C D
MENU
INPUT
TV
STR
DVD
AUD
EXIT
OK
ENTER
SETUP
SLEEP
CH
6
9
8
13
14
15
21
11
10
12
16
17
18
19
20
5
4
7
1
2
3

5
Button Functions
1. Power - Turns devices ON/OFF (on side)
2. Volume up/down (on side)
3. Mute - Mutes sound (on side)
4. Home/Guide - Access features on streaming
devices or Guide on cable/satellite receivers
5. Input - Selects video inputs
6. Menu - Displays the on-screen menu
7. TV, STR, DVD, AUD - Selects the device
to control
8. Ok - Selects menu items for the controlled
device
9. Up/down/left/right menu navigation
10. Exit - Exit on-screen menus
11. Info - Displays on-screen show/content
information
12. Channel up/down
13. Record, play, stop, rewind, fast forward, pause
14. ABCD - Access additional features for DVRs,
cable and satellite receivers
15. Numbers - Enter numbers for direct channel
selection
16. Previous Channel - Returns to the previously
selected channel
17. DVD/Blu-ray™open/close - Open/close a player,
or List features on cable/satellite receivers
18. Sleep - Sleep timer functions
19. Setup - Used to program the remote
20. Dash (-) - Used to select digital channels
21. Enter -Some devices require enter to be
pressed after channel selection

6
Programming Your Remote
Your remote is designed to control multiple audio/
video devices. To use, you will need to program the
remote for your devices. There are two dierent
methods you can use to program the remote,
Direct Code Entry or Auto Code Search.
• The Direct Code Entry method is the
recommended method as it is the simplest
and quickest method in most cases.
• The Auto Code Search method searches
through all the codes in the remote to nd a
code for your device.
Note:This remote comes preprogrammed for
Roku®boxes and Samsung TVs. Press TV for
Samsung TVs and STR for Roku boxes.
Direct Code Entry (Recommended)
1. Locate the Code List included with
your remote. Find the section for the
type of device you wish to control,
(for example TV, STR, DVD, AUD.
Locate the brand of your device and
circle all the remote codes for the
brand.
2. Press and hold down the SETUP
button on the remote until the red
light on the remote control turns on.
Release the SETUP button. The red
light will remain on.
Note: The red light will either be a
small light at the top of the remote
or the power ON/OFF button.
3. Press and release the device button
on the remote for the type of device
you wish to control, (for example TV,
STR, DVD, AUD). The red light will
blink once and remain on.
Note:Any of the device buttons on
the remote can be programmed
to control any of your devices. For
example, you can use the DVD
device button on the remote to
control a satellite receiver, digital
converter box, streaming media
player or any device category in the
Code List.
A
1 2 3
4 5 6
7
(-)
8
0
9
B C D
MENU
INPUT
TV
STR
DVD
AUD
EXIT
OK
ENTER
SETUP
SLEEP
CH
A
1 2 3
4 5 6
7
(-)
8
0
9
B C D
MENU
INPUT
TV
STR
DVD
AUD
EXIT
OK
ENTER
SETUP
SLEEP
CH
A
1 2 3
4 5 6
7
(-)
8
0
9
B C D
MENU
INPUT
TV
STR
DVD
AUD
EXIT
OK
ENTER
SETUP
SLEEP
CH

7
Programming Your Remote
4. Use the number buttons on the
remote to enter the rst 4-digit
remote code you circled in the Code
List in Step 1. The red light will turn
o after entering the fourth digit.
5. Point the remote at the device.
Test the buttons on the remote to
see if the device responds as you
would expect. If the buttons do not
operate the device, return to Step
2 above and use the next code that
you circled for that device.
6. Repeat Steps 1 – 5 for each device you wish
to control.
Programming Notes
• Some codes may operate only a few functions
of your device. There may be another code in
the Code List that controls more functions.
Test other codes in the Code List for more
functionality.
• If you do not nd a remote code that works your
device or there are no codes in the Code List for
your device, use the Auto Code Search method
in the next section to program your remote.
• For combination devices such as a TV/DVD
combo or TV/VCR combo, you may have to enter
a code for each device. (See Controlling Combo
Devices.)
• Write down the remote codes used to program
the remote for future reference.
A
1 2 3
4 5 6
7
(-)
8
0
9
B C D
MENU
INPUT
TV
STR
DVD
AUD
EXIT
OK
ENTER
SETUP
SLEEP
CH
A
1 2 3
4 5 6
7
(-)
8
0
9
B C D
MENU
INPUT
TV
STR
DVD
AUD
EXIT
OK
ENTER
SETUP
SLEEP
CH

8
Programming Your Remote
Auto Code Search
The Auto Code Search is a process where you can
search through all the codes stored in the remote
to nd a code for your device. It is recommended
that you read through all the steps below to
familiarize yourself with the Auto Code Search
before starting the process.
1. Manually turn on the device you wish
to control.
Note: The Auto Code Search process
cannot be used for devices without
power ON/OFF capability. Use the
Direct Code Entry method in these
cases.
2. Press and hold down the SETUP
button on the remote until the red
light on the remote control turns on.
Release the SETUP button. The red
light will remain on.
Note:The red light will either be a
small light at the top of the remote or
the power ON/OFF button.
3. Press and release the device button
on the remote for the type of device
you wish to control, (for example TV,
STR, DVD, AUD). The red light will
blink once and remain on.
4. With the remote pointed at the
device, press and release the POWER
button on the remote. The remote will
send 10 dierent codes to the device.
The red light will blink once for each
code and remain on after sending the
10 codes.
Did the device turn o?
• If YES, go to Step 5.
• If NO, repeat Step 4 to test the next
10 codes.
5. Manually turn the device back on.
6. With the remote pointed at the
device, press and release the VOL+
button.
A
1 2 3
4 5 6
7
(-)
8
0
9
B C D
MENU
INPUT
TV
STR
DVD
AUD
EXIT
OK
ENTER
SETUP
SLEEP
CH
A
1 2 3
4 5 6
7
(-)
8
0
9
B C D
MENU
INPUT
TV
STR
DVD
AUD
EXIT
OK
ENTER
SETUP
SLEEP
CH
A
1 2 3
4 5 6
7
(-)
8
0
9
B C D
MENU
INPUT
TV
STR
DVD
AUD
EXIT
OK
ENTER
SETUP
SLEEP
CH
A
1 2 3
4 5 6
7
(-)
8
0
9
B C D
MENU
INPUT
TV
STR
DVD
AUD
EXIT
OK
ENTER
SETUP
SLEEP
CH

9
Programming Your Remote
The remote will re-send the rst code of the
10 codes from Step 4. The red light will blink
once and remain on.
Did the device turn o?
• If YES, you have found a code for the
device. Press and release the same device
button you pressed in Step 3. This will
store the code in the remote. Go to Step 7.
• If NO, continue to press and release the
VOL+ button until the device turns o to
test the other 9 codes from Step 4.
Be sure to wait approximately 3 seconds
after each VOL+ button press to allow
the device time to respond to the code.
When the device turns o, you have
found a code for your device. Press and
release the same device button pressed
in Step 3. This will store the code in the
remote. Go to Step 7.
Notes:
• The VOL– button can be used to go
backwards through each batch of 10
codes.
• The red indicator light will ash 2 times
after testing the rst or last code in each
batch of 10.
7. Use the remote to turn the device back
on. Test the buttons on the remote to
see if the device responds as you would
expect. If the buttons do not operate the
device, return to Step 2 and repeat this
process to search for a better code to
operate the device.
8. Repeat this process for each device you
wish to control.
Controlling Combo Devices
Some combo devices (e.g. TV/VCR, TV/DVD, DVD/
VCR, etc.) will require you to set up two dierent
device buttons to control both parts of the combo
device. For example, if you have a TV/DVD combo,
you may need to set up one code under the TV
button to control the TV and a separate code
under the DVD button to control the DVD.
A
1 2 3
4 5 6
7
(-)
8
0
9
B C D
MENU
INPUT
TV
STR
DVD
AUD
EXIT
OK
ENTER
SETUP
SLEEP
CH
A
1 2 3
4 5 6
7
(-)
8
0
9
B C D
MENU
INPUT
TV
STR
DVD
AUD
EXIT
OK
ENTER
SETUP
SLEEP
CH
A
1 2 3
4 5 6
7
(-)
8
0
9
B C D
MENU
INPUT
TV
STR
DVD
AUD
EXIT
OK
ENTER
SETUP
SLEEP
CH

10
Using Your Remote
Primary Audio Control
The primary audio control feature allows you to
select a single device that the volume buttons
always control. For example, the remote can be
in TV mode while the volume buttons control the
volume on your audio receiver or sound bar instead
of your TV.
Enabling the Primary Audio Control
Feature
1. Press and hold down the SETUP
button on the remote until the red
light on the remote control turns on.
Release the SETUP button. The red
light will remain on.
2. Press and release the device button
(TV, AUD, etc.) on the remote for
the device you wish to control the
volume.
3. Press and release the MUTE button.
4. Press and release the VOL+ button.
The red light will blink twice and
turn o.
Disabling the Primary Audio Control
Feature
1. Press and hold down the SETUP
button on the remote until the red
light on the remote control turns on.
Release the SETUP button. The red
light will remain on.
2. Press and release the device button
(TV, AUD, etc.) programmed to
control the primary audio control
feature.
3. Press and release the MUTE button.
4. Press and release the VOL- button.
The red light will blink twice and
turn o.
A
1 2 3
4 5 6
7
(-)
8
0
9
B C D
MENU
INPUT
TV
STR
DVD
AUD
EXIT
OK
ENTER
SETUP
SLEEP
CH
A
1 2 3
4 5 6
7
(-)
8
0
9
B C D
MENU
INPUT
TV
STR
DVD
AUD
EXIT
OK
ENTER
SETUP
SLEEP
CH
A
1 2 3
4 5 6
7
(-)
8
0
9
B C D
MENU
INPUT
TV
STR
DVD
AUD
EXIT
OK
ENTER
SETUP
SLEEP
CH
A
1 2 3
4 5 6
7
(-)
8
0
9
B C D
MENU
INPUT
TV
STR
DVD
AUD
EXIT
OK
ENTER
SETUP
SLEEP
CH
A
1 2 3
4 5 6
7
(-)
8
0
9
B C D
MENU
INPUT
TV
STR
DVD
AUD
EXIT
OK
ENTER
SETUP
SLEEP
CH
A
1 2 3
4 5 6
7
(-)
8
0
9
B C D
MENU
INPUT
TV
STR
DVD
AUD
EXIT
OK
ENTER
SETUP
SLEEP
CH
A
1 2 3
4 5 6
7
(-)
8
0
9
B C D
MENU
INPUT
TV
STR
DVD
AUD
EXIT
OK
ENTER
SETUP
SLEEP
CH
A
1 2 3
4 5 6
7
(-)
8
0
9
B C D
MENU
INPUT
TV
STR
DVD
AUD
EXIT
OK
ENTER
SETUP
SLEEP
CH