Philips SRP3219G/27 User manual

User manual
Audio/Video
SRP3219G/27
v1 12/19
SRP3229G/27
SRP3239R/27
SRP3249B/27

2
Introduction ............................................................. 2
Setup......................................................................... 3
Button Functions ....................................................4
Programming Your Remote ...................................6
Direct Code Entry ..............................................6
Auto Code Search.............................................. 7
Controlling Combo Devices .............................9
Using Your Remote ............................................... 10
Code Identication.......................................... 10
Reset to Factory Settings............................... 10
Primary Audio Control..................................... 11
Troubleshooting................................................12
Warranty..................................................................13
FCC Statement ...................................................... 14
Congratulations on your purchase of this Philips
branded Universal Remote Control. This remote
is capable of operating thousands of audio/
video devices including TVs, Blu-ray™/DVD
players, streaming media players, sound bars,
cable receivers and more!
Table of Contents
SAVE THIS MANUAL AND CODE LIST
FOR FUTURE REFERENCE
https://byjasco.com/urccodes

3
Your universal remote requires two (2) AAA
batteries (not included). Alkaline batteries are
recommended.
Battery Installation
1. On the back of the remote, pull down on
the textured surface and slide battery cover
downward to remove.
2. Match the (+) and (-) marks on the batteries
to the (+) and (-) marks inside the battery
compartment, then insert two (2) AAA
batteries. Be sure to use fresh batteries.
3. Position battery cover slightly below opening
and push upward to lock into place.
NOTE:If your remote stops operating properly,
replace the batteries with new ones.
Battery Precautions
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-
zinc), or rechargeable (Ni-Cd, Ni-MH, etc.)
batteries.
• Always remove old, weak or worn-out
batteries promptly and recycle or dispose of
them in accordance with local and national
regulations.
Battery Saver
Your remote automatically turns o if the
buttons are depressed more than 8 seconds.
This will save your batteries should your remote
get stuck in a place where the buttons remain
depressed (e.g., between the sofa cushions).
Code Saver
You have up to 10 minutes to change the
batteries in your remote without losing the
codes you have programmed.
Setup

4
7
13
14
17
19
20
21
18
16
3
4
1
88
9 9
11 11
2
6
5
15
10
12
Button Functions

5
Button Functions
1. Power - Turns devices ON/OFF
2. TV, STR, AUD - Selects the device to control
3. Info/Options - Displays on-screen show/
content information
4. Exit -Exit on-screen menus
5. Record, play, stop, rewind, fast
forward, pause
6. DVD/Blu-ray™open/close - open/close a
player, or List features on cable/satellite
receivers
7. Up/down/left/right menu navigation
8. Last channel - Returns to the previously
selected channel
9. Channel up/down
10. ABCD - Access additional features for DVRs,
cable and satellite receivers
11. Numbers - Enter numbers for direct
channel selection
12. Dash (-) - Use to select digital channels,
e.g., 4.1
13. Enter key (Some devices require enter to
be pressed after channel selection)
14. Volume up/down
15. Mute - Mutes sound
16. Ok - Selects menu items for the
controlled device
17. Setup - Used to program the remote
18. Streaming App Hotkey - Access top apps
like Netix®, Amazon®Prime, Hulu®and more
19. Home/Guide - Easily access features on
today’s streaming devices, or Guide on
cable/satellite receivers
20. Menu - Displays the on-screen menu
21. Input - Selects video inputs

6
Programming Your Remote
Your remote is designed to control multiple
audio/video devices. To use, you will need to
program the remote for your devices. There
are two dierent methods you can use to
program the remote, Direct Code Entry or
Auto Code Search.
• The Direct Code Entry method is the
recommended method as it is the simplest
and quickest method in most cases.
• The Auto Code Search method searches
through all the codes in the remote to nd a
code for your device.
NOTE:This remote comes preprogrammed for
Roku®boxes and Samsung TVs. Press TV for
Samsung TVs and STR for Roku boxes.
Direct Code Entry (Recommended)
1. Locate the Code List included
with your remote. Find the section
for the type of device you wish to
control, (for example TV, STR, AUD).
Locate the brand of your device
and circle all the remote codes for
the brand.
2. Press and hold down the SETUP
button on the remote until the red
light on the remote control turns
on. Release the SETUP button.
The red light will remain on.
NOTE:The red light will either be a
small light at the top of the remote
or the power ON/OFF button.
3. Press and release the device
button on the remote for the type
of device you wish to control, (for
example TV, STR, AUD). The red
light will blink once and remain on.
NOTE:Any of the device buttons
on the remote can be programmed
to control any of your devices. For
example, you can use the aux device
button on the remote to control a
Satellite Receiver, Digital Converter
Box, Streaming Media Player or any
device category in the Code List.

7
Programming Your Remote
4. Use the number buttons on the
remote to enter the rst 4-digit
remote code you circled in the
Code List in Step 1. The red light
will turn o after entering the
fourth digit.
5. Point the remote at the device.
Test the buttons on the remote
to see if the device responds as
you would expect. If the buttons
do not operate the device, return
to Step 2 above and use the next
code that you circled for that
device.
6. Repeat steps 1 – 5 for each
device you wish to control.
Programming Notes
• Some codes may operate only a few
functions of your device. There may be
another code in the Code List that controls
more functions. Test other codes in the
Code List for more functionality.
• If you do not nd a remote code that works
your device or there are no codes in the
Code List for your device, use the Auto
Code Search method in the next section to
program your remote.
• For combination devices such as a TV/DVD
combo or TV/VCR combo, you may have to
enter a code for each device.
• Write down the remote codes used to
program the remote for future reference.
Auto Code Search
The Auto Code Search is a process where you
can search through all the codes stored in
the remote to nd a code for your device. It is
recommended that you read through all the
steps below to familiarize yourself with the
Auto Code Search before starting the process.

8
Programming Your Remote
1. Manually turn on the device you
wish to control.
NOTE:The Auto Code Search process
cannot be used for devices without
power ON/OFF capability. Use the
Direct Code Entry method in these
cases.
2. Press and hold down the SETUP
button on the remote until the red
light on the remote control turns on.
Release the SETUP button. The red
light will remain on.
NOTE:The red light will either be a
small light at the top of the remote or
the power ON/OFF button.
3. Press and release the device button
on the remote for the type of device
you wish to control, (for example TV,
STRM, AUX). The red light will blink
once and remain on.
4. With the remote pointed at the
device, press and release the
POWER button on the remote. The
remote will send 10 dierent codes
to the device. The red light will blink
once for each code and remain on
after sending the 10 codes.
Did the device turn o?
• If YES, go to Step 5.
• If NO, repeat Step 4 to test the
next 10 codes.
5. Manually turn the device back on.
6. With the remote pointed at the
device, press and release the
VOL button. The remote will re-
send the rst code of the 10 codes
from Step 4. The red light will blink
once and remain on.
Did the device turn o?
• If YES, you have found a code for
the device. Press and release the
same device button you pressed
in Step 3. This will store the code
in the remote. Go to Step 7.

9
Programming Your Remote
• If NO, continue to press and
release the VOL button until
the device turns o to test the
other 9 codes from Step 4. Be
sure to wait approximately
3 seconds after each VOL
button press to allow the device
time to respond to the code.
When the device turns o, you
have found a code for your
device. Press and release the
same device button pressed in
Step 3. This will store the code
in the remote. Go to Step 7.
NOTE:
• The VOL button can be used to
go backwards through each batch
of 10 codes.
• The red indicator light will ash 2
times after testing the rst or last
code in each batch of 10.
7. Use the remote to turn the device
back on. Test the buttons on
the remote to see if the device
responds as you would expect.
If the buttons do not operate the
device, return to Step 2 and repeat
this process to search for a better
code to operate the device.
8. Repeat this process for each
device you wish to control.
Controlling Combo Devices
Some combo devices (e.g. TV/VCR, TV/DVD,
DVD/VCR, etc.) will require you to set up two
dierent device buttons to control both parts
of the combo device. For example, if you have
a TV/DVD combo, you may need to set up one
code under the TV button to control the TV
and a separate code under the DVD button to
control the DVD.

10
Using Your Remote
1. Press and hold down the SETUP
button on the remote until the
red light on the remote control
turns on. Release the SETUP
button. The red light will
remain on.
2. Press and release the desired
device button (TV, STRM, AUD)
you would like the code for.
3. Press and release the
ENTER button.
4. Press and release the #1 button.
Count the number of times the
remote light ashes. This is the
number corresponding to the
rst digit of the code. Repeat the
process by pressing the #2, #3
and #4 buttons for the remaining
digits.
5. Press and release the ENTER
button to exit this mode.
Code Identication
Reset to Factory Settings
1. Press and hold down the SETUP
button on the remote until the
red light on the remote control turns
on. Release the SETUP button. The
red light will remain on.
2. Press and release the
MUTE button.
3. Press and release the number #0
button. The red indicator light will
ash twice.