Philips MICRO UNDERWATER User manual

®
LISTED
[COUVERT "TWIST-LOCK"]
PIVOTANT REGLABLE)]
[DOUILLE A DEUX BROCHES]
INCLUDED)[NON COMPRIS]
[JOINT EN SILICONE]
[PROTECTEUR DE LENTILLE EN
POLYCARBONATE TRANSPARENT]
[CONNECTEUR ETANCHE]
[BOITIER DU LUMINAIRE]
[VIS DE FIXATION DU COUVERCLE]
[CABLE SOUS-MARIN DE 10 PI]
ADJUSTABLE LOCKING
SWIVEL ARM) [BASE EN
BETON (AVEC BRAS
FACTORY SEALED
CLEAR POLYCARBONATE LENS GUARD
50W MAX., 12V
MR16 LAMP (NOT
FIXTURE HOUSING
CONCRETE BASE (WITH
TWIST-LOCK FIXTURE COVER
COVER LOCKING SCREW
10' UNDERWATER CABLE
SILICONE GASKET
LIQUID-TIGHT CONDUIT FITTING
BI-PIN TYPE SOCKET
32000781, revision F
100 Craftway, P.O. Box 128
Littlestown, Pennsylvania 17340-0128
Phone: [phone] Fax: [phone]
INSTALLATION INSTRUCTIONS:
MICRO UNDERWATER
page 1 of 2
SAFETY WARNING:
ALWAYS TURN FIXTURE OFF/DISCONNECT POWER AND ALLOW TO COOL BEFORE
PERFORMING ANY MAINTENANCE, INCLUDING RELAMPING AND CLEANING!
This fixture can become very HOT! The fixture housing and lens, especially if it is glass, can become hot enough
to blister hands. Attention should be paid to where the fixture is mounted, particularly if it can be touched by
children or pets. To help prevent premature failure, decreased performance, overheating and risk of fire, keep
fixture and lens clean and free of leaves, mulch, debris and mineral deposits from water. The fixture and lens
can be cleaned using a soft cloth and a solution of mild liquid soap and warm water. Wipe clean and dry with a
soft, lint-free dry cloth. Avoid polishing fixture or lens.
This fixture is intended for installation in accordance with the National Electrical Code and local code
specifications. Failure to adhere to these codes and instructions may result in serious injury and/or damage
to the ballast and void the warranty. These instructions do not purport to cover all details or variations in
equipment, nor to provide for every possible contingency related to installation, operation, maintenance,
or mounting situation. Should specific problems occur that are not addressed by these instructions, contact
your Sales Representative or distributor for assistance. Retain these instructions for future reference.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE OR INJURY TO PERSONS
IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS!
WARNING - Lamp gets HOT quickly! To reduce the risk of FIRE OR INJURY TO PERSONS:
Do not operate fixture with a missing or damaged lens/lens assembly.
Contact only switch or plug when turning fixture on or off. Do NOT touch hot lens or housing.
Turn off or unplug fixture and allow to cool before relamping. Keep lamp away from combustibles.
Do NOT touch lamp with bare hands at any time, use a soft cloth as oil from skin may damage lamp.

transformateur]
REMARQUE:
Ce schema est conforme au Code
national de l'electricite.
[Support de
[Cable sous-marin]
[Conduit (non compris)]
1 pi
4 pi
[Transformateur (non compris)]
Transformer Support
Conduit (By others)
Underwater Cable
Transformer (Not included)
Not less than 16"
4 ft. 1 ft.
Code Article 680-5, 680-21, and 680-52.
This diagram is per National Electrical
NOTE:
DECK
50W, MR16, WFL, 38°
50W, MR16, MFL, 24°
50W, MR16, NSP, 12°
42W, MR16, WFL, 36°
42W, MR16, MFL, 20°
42W, MR16, NSP, 9°
35W, MR16, WFL, 35°
35W, MR16, MFL, 21°
35W, MR16, NSP, 12°
20W, MR16, WFL, 40°
20W, MR16, NSP, 13°
20W, MR16, VNSP, 6°
des lampes suivantes.]
[Ce luminaire peut etre pourvu
used in this fixture.
The following lamps may be
CAUTION!
1. TO PREVENT ELECTRICAL SHOCK, DISCONNECT TRANSFORMER FROM ELECTRIC SUPPLY BEFORE SERVICING.
2. DO NOT let the fixture freeze. This may cause cracking or deformation that may cause
the fixture to leak, or cause safety problems.
3. DO NOT hold fixture by or pull the underwater cable. If wire is pulled it may break
the liquid-tight seal and void the warranty.
4. DO NOT use the fixture out of water with the polycarbonate lens guard on. If the fixture is not
used as an under-water fixture, remove the clear polycarbonate lens guard or it will distort and soften.
and result in possible leakage.
5. DO NOT loosen or remove the liquid-tight connector, this will damage the factory set seal
8. The fixture is rated Max. 50 W, (12) Volt AC, DO NOT connect fixture to any other voltage.
6. The end of the underwater cable MUST BE POTTED to prevent moisture from entering the cable
and consequently into the fixture. (See fig. 1).
7. The fixture is to be directly connected to a U.L. LISTED Low Voltage Transformer intended for this
application. (See fig. 2).
SERVICING INSTRUCTIONS
1. LAMP INSTALLATION / REPLACEMENT:
a) Remove the fixture from the water.
b) Loosen cover locking screw to remove cover.
c) Unscrew the cover by turning it counterclockwise. Remove the lens
and O-ring.
d) Remove and install lamp. DO NOT exceed the maximum 50 W
rating. The lamp is a standard 12V halogen, type MR-16, bi-pin.
e) To remove lamp, pull on lamp reflector. Do not pull on the small
bulb within the reflector.
f ) To install lamp, plug the lamp into the bi-pin socket. DO NOT touch
the new halogen bulb. Only touch the lamp reflector. Touching
the bulb may shorten lamp life.
g) The O-ring seating surfaces must be clean. Be certain that the
O-ring is in good condition and clean. Reinstall O-ring and lens.
h) Reinstall the fixture cover. Look through the (3) slots on cover, hand
tighten cover by turning it clockwise until the (3) tabs on cover
touch the stops on the housing.
i ) Tighten the cover locking screw to lock in place.
2. MAKE CERTAIN NO WATER OR MOISTURE IS INSIDE FIXTURE PRIOR TO
REASSEMBLING.
3. CLEANING: The lens will require periodic cleaning. Wipe off the
outside of the lens with a soft cloth. DO NOT use abrasives. This may
damage the lens.
page 2 of 2
32000781, revision F