Philips Impact-plus FC 8388 User manual

ServiceManual
Philips Domestic Appliances and Personal Care
Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification
Impact-plus Vacuum cleaner
FC 8388
PRODUCT INFORMATION
- Maximum air displacement : 31 l/sec
- Maximum vacuum water column : 350 cm
- Power consumptio (IEC) 225V : 1400 W
- Dust storage capacity : 2 litres
- Cord length (depends on version) : 6.3 m
- Filter system : 5 filters
- Dimensions cleaner : 37 x 28 x 23 cm
- Weight accessoiries : 4.8 kg
- Noise : 80 dB max.
- Colour : Malibu blue
- Electronic controled motor rpm
- Cordwinder build-in with flat cord
- Dustbag-full indicator in dustcover
OPTIONAL
Exhaust air filter FC 8032 (4822 015 70056)
S-cotton dustbag HR 6997 (4822 480 10115)
S-paper dustbags FC 8021 (4822 480 10113)
Clinic dustbags FC 8022 (8838 022 01010)
4322 277 00868
02/08
SERVICE INFORMATION
- To open the appliance, first remove the screws A,B,C,D.
- To reach the motor remove the screws E.
- To disassemble the cordwider use Torx screw driver no T10,
which is one of set consisting of T20, T15, T10, T9, T8, T7 and
T6 = 4822 395 50145.
- Give attention that the contact fingers (item 45) are placed on the
cord-winder shaft in such a way that the pressure point of the
cordwinder knob to the cord winderlever (item 40) is vertical.
- The spare parts have been standardized as much as possible.
- Component configuration on exploded view may differ in case
of specific versions, however, the actual components are distin-
guished by means of code numbers.
- Item 1 Cotton dustbag is used in those countries where paper
dustbags are not available
- Item 41 Cord-winder spring unit is provided with a long spring,
both long and short cords can be used in combination with this
spring.
- Cordwinder spring has to be tensioned till maximum minus
approx. 1,5 revolution.
This product meets the requirements regard-
ing interference suppression on radio and TV.
After the product has been repaired, it should
function properly and has to meet the safety
requirements as officially laid down at this
moment.

Pos. 12 nc description
1 4822 480 10115 S-cotton dustbag HR 6997 (opt.)
8838 022 01010 Clinic dustbags FC 8022 (opt.)
4822 480 10113 S-paper dustbags FC 8021
2 4322 009 07670 dustbag holder (grey)
3 4322 009 08520 upperhousing (el.)
4 4322 001 73150 inletrubber
5 4322 003 17250 nose piece
6 4322 001 99290 wheel (24)
7 4322 002 22260 spindle
8 4322 009 08510 lower housing
9 4322 003 21150 handle el. (malibu blue)
10 4322 009 08580 vario knob
11 4322 009 08570 dust cover (malibu blue)
12 4322 001 72900 motor buffer
13 4322 001 73160 sealing m.c.
14 4322 000 35360 duo filter
14A 4322 009 08460 duo filter and holder
15 4322 003 17740 hinge (grey)
16 4322 009 07730 cord outlet
17 4322 003 17320 backgrille (grey)
18 4822 015 70056 exhaust filter
19 4322 009 08500 rear wheel
20 4322 003 21200 knobs (malibu blue)
21 4322 000 09750 pedal spring
22 4322 006 20080 Low Volt PCB
4322 006 22210 High Volt PCB
22A 4322 006 50600 switch (soldered version)
23 4322 001 73230 cooling connection
24 4322 003 21030 motor cap (grey)
25 4322 001 72780 buffer ring front
26 4322 006 97400 motor 110 V - 60 Hz / ans
4322 009 06430 motor 220 - 240 V / ans
28 4322 009 07520 motor foam/disc/ans
Pos. 12 nc description
40 4322 003 06620 push rod
41 4322 009 07610 reelhalf springside
42 4322 001 72360 brake tyre
43 4322 009 07640 base plate
44 4322 009 07620 reelhalf contactside
45 4322 009 07630 contact plate
46 4322 006 01880 Argentina L = 6.3 m
4322 006 01380 Australia L = 6.3 m
47 4322 006 01770 Japan / Taiwan L = 5.3 m
48 4322 006 01370 H.K. / U.K. L = 6.3 m
49 4322 006 01400 Euro 4.8 mm L = 6.3 m
50 4322 006 01480 Swiss L = 6.3 m
51 4322 006 01430 Italy L = 6.3 m
54 4341 004 20100 small nozzle
55 4341 003 00240 tube clip (opt.)
56 4322 002 22610 steel tube painted con. 55 cm. (opt.)
57 4341 004 20420 bend + hose
58 4341 005 01240 bend handle
59 4341 004 20170crevice nozzle
60 4322 004 21180 nozzle D272
61 4822 479 20039 nozzle brush
62 4822 479 20038 nozzle strip
63 4322 003 10020 clip telescopic tube
64 4322 004 21050 telescopic tube
M
SPEED
CONTROL UNIT
CORD WINDER
C

C
CD
10
3
6
40
2
1
5
4
45
46÷51
42
11
8
41
43
44
9
7

DAP2211
A
B
B
E
C
D
E
21
22
10
15
18
12
24
25
26
23
20
16
11
19
9
17
28
13
14A
14
22A

DAP2207
60
61
62
57
58
46AUSTRALIA
JAPAN 47
EUROPE Ø 4.8mm 49
CH 50
ITALY 51
48GB
54 59
56
64
5563