Phoenix Model CANARY User manual

Wingspan : 1573mm (62inch)
Length : 1255mm (49.4inch)
Weight : 2650gr
Engine : 40 - 46 two stroke
Radio : 4 channel - 4 servos standard
g
We wish you many enjoyable flights with your plane and one again thank you for your choosing a Phoenix Model products.
Instruction Manual
al
Instruction Man
uc
tion Manua
l
ion Man
Instruction
CANARY

1
1 2
3 4
5 6
7 8
Draw a center line. Remove the covering.
Glue the wing joiner to the wing. Apply the epoxy into the wing section.
Glue the wing by epoxy. Apply the trim tape to the center section of the wing where
they join.
Remove the covering. Glue the two hard wood by C.A glue.
Canary
Instruction Manual
Jo
i
n
i
ng the w
i
ng halves
.
Joining the wing halves.
1
Center line
Installing the aileron servo and linkage.
2

2
910
11 12
13 14
15 16
Mark the shape of the servo box to the wing. Remove the covering.
Glue the servo box by C.A glue. Install and secure the aileron servo.
Install the two nylon control horn. Attach the clevis to the control horn.
Cut away the aileron pushrod. Bend "L" the aileron pushrod.
Canary
Instruction Manual
Nylon control horn
Silicon tube
Silicon tube

3
17 18
19 20
21
22 23
Attach the nylon clasp to the aileron servo arm. Make the same way to install the second aileron pushrod.
Draw a center line. Remove the covering from the fuselage.
Attach the horizontal to the fuselage and check it. Check the horizontal and the wing.
Mark the shape of the fuselage onto the top and bottom of
the horizontal.
Remove the covering from the top of the horizontal.
Canary
Instruction Manual
Nylon clasp
I
nstall
i
ng the hor
i
zontal and vert
i
cal.
Installing the horizontal and vertical.
3
Center line
A1 A2
A1 = A2
A1 A2

4
24 25
26
27 28
29 30
Remove the covering from the bottom of the horizontal. Glue the horizontal and fuselage by epoxy and check it.
Check the horizontal and the wing. Cut away the covering from the fuselage.
Mark the shape of the fuselage onto the both side of the
vertical.
Remove the covering from the vertical.
Remove the covering on the top of the fuselage. Glue the vertical into the fuselage by epoxy and check it.
Canary
Instruction Manual
AA1
BB1

5
31 32
33 34
35 36
Check the fin before it dry and remove the wing out of the
fuselage.
The landing gear and nose gear. Install the collar.
Install the wheel. Cut away the covering on the fuselage.
Install the landing gear. Secure the landing gear.
Canary
Instruction Manual
a1 a2
a1 = a2
J
oinin
g
the landin
g
g
ear and nose
g
ear
.
Joining the landing gear and nose gear.
4
Collar
Gear
Collar

6
37 38
39
40 41
42 43
Install the wheel. Attach the wire pushrod to the steering arm.
Install the nose gear and secure it.
The control horn and pushrod. Insert the silicon tube to the clevis of the rudder pushrod.
Remove the covering. Insert the ruder pushrod into the fuselage.
Canary
Instruction Manual
Installin
g
the rudder and elevator
p
ushrod.
Installing the rudder and elevator pushrod.
5
Silicon tube

7
44 45
46 47
48 49
50 51
Install the nylon control horn. Attach the clevis to the control horn.
Install the rudder servo. Install the metal connector to the servo arm.
Connect the rudder pushrod and the nose gear pushrod to
the rudder servo.
Secure the nose gear pushrod.
Cut away the rudder pushrod. Bend "L" the rudder pushrod.
Canary
Instruction Manual
Control horn
Clevis
Control horn

8
52 53
54 55
56 57
58 59
Attach the nylon clasp to the servo arm. Remove the covering from the slot.
Insert the elevator pushrod into the fuselage. Install the control horn.
Attach the clevis to the control horn. Install the elevator servo.
Cut away the elevator pushrod. Bend "L" the elevator pushrod.
Canary
Instruction Manual

9
60
61 62
63 64
65 66
Attach the nylon clasp to the servo arm.
Cut away the fuel tube. Install the stopper to the tank.
Secure the stopper. Install the silicone tube to the tank.
Slide the fuel tank into the fuselage. Secure the fuel tank by foam and wood.
Canary
Instruction Manual
I
nstallin
g
the fuel tank
.
Installing the fuel tank.
6
5mm