Photon Focus Luxima MV4-D1280-L01-G2 User manual

Photonfocus
MV4 Luxima Camera Series
CMOS camera series with GigE Interface
MV4-D1280-L01-G2
MV4-D1280-L01-GT
MV4-D1280-L01-FB
DR4-D1280-L01-G2
DR4-D1280-L01-GT (available on request)
DR4-D1280-L01-FB (available on request)
MV4-D1952-L01-G2 (available on request)
MV4-D1952-L01-GT
MV4-D1952-L01-FB (available on request)
DR4-D1952-L01-G2 (available on request)
DR4-D1952-L01-GT
DR4-D1952-L01-FB (available on request)
MAN085 04/2021 V1.3

All information provided in this manual is believed to be accurate and reliable. No
responsibility is assumed by Photonfocus AG for its use. Photonfocus AG reserves the right to
make changes to this information without notice.
Reproduction of this manual in whole or in part, by any means, is prohibited without prior
permission having been obtained from Photonfocus AG.
2 of 151 MAN085 04/2021 V1.3

Contents
1 Preface 9
1.1 IMPORTANTNOTICE! ..................................... 9
1.2 AboutPhotonfocus...................................... 10
1.3 Contact............................................. 10
1.4 SalesOffices .......................................... 10
1.5 Furtherinformation...................................... 10
1.6 Legend ............................................. 11
2 Introduction 13
2.1 Introduction .......................................... 13
2.2 CameraNamingConvention................................. 13
2.3 Cameralist........................................... 13
3 Product Specification 15
3.1 Introduction .......................................... 15
3.2 FeatureOverview ....................................... 18
3.3 TechnicalSpecification .................................... 19
3.3.1 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.3.2 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.3.3 SpectralResponse................................... 24
4 Image Acquisition 25
4.1 Overview............................................ 25
4.1.1 Vocabulary....................................... 25
4.1.2 Structure ........................................ 25
4.1.3 Image Acquisition, Frame and Exposure Control Parameters . . . . . . . . . . 26
4.1.4 Image Acquisition, Frame and Exposure Trigger . . . . . . . . . . . . . . . . . 27
4.1.5 Image Acquisition, Frame and Exposure Status . . . . . . . . . . . . . . . . . . 27
4.2 AcquisitionControl ...................................... 28
4.2.1 Acquisition Start and Stop Commands, Acquisition Mode and Acquisition
FrameCount...................................... 28
4.2.2 Acquisition Frame Rate and Acquisition Frame Rate Enable . . . . . . . . . . 28
4.2.3 Acquisition Start Trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.2.4 Acquisition End Trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4.2.5 Acquisition Control Output Signals . . . . . . . . . . . . . . . . . . . . . . . . . 30
4.3 FrameControl ......................................... 31
4.3.1 FrameStartTrigger.................................. 31
4.3.2 Frame Burst Start Trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4.3.3 FrameBurstEndTrigger ............................... 32
4.3.4 Frame Control Output Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.4 ExposureControl ....................................... 34
4.4.1 ExposureMode .................................... 34
MAN085 04/2021 V1.3 3 of 151

CONTENTS
4.4.2 ExposureStartTrigger ................................ 34
4.4.3 ExposureEndTrigger................................. 34
4.4.4 Exposure Control Output Signals . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.5 Overlapped Image Acquisition Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.6 Acquisition-, Frame- and Exposure-Trigger Configuration . . . . . . . . . . . . . . . . 38
4.6.1 Trigger Source Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4.6.2 TriggerSoftware ................................... 39
4.6.3 TriggerMode ..................................... 39
4.6.4 TriggerActivation................................... 39
4.6.5 TriggerDivider..................................... 40
4.6.6 TriggerDelay...................................... 40
4.7 Software Signal Pulse and User Output . . . . . . . . . . . . . . . . . . . . . . . . . . 41
5 Counter & Timer 43
5.1 Counter............................................. 43
5.1.1 CounterUsage..................................... 43
5.1.2 CounterStatus..................................... 44
5.1.3 Counter Active, -Start and -End Signal . . . . . . . . . . . . . . . . . . . . . . . 44
5.1.4 CounterReset ..................................... 44
5.1.5 CounterEventSource................................. 45
5.1.6 CounterTriggerSource................................ 46
5.1.7 CounterResetSource................................. 47
5.2 Timer .............................................. 49
5.2.1 TimerUsage ...................................... 49
5.2.2 TimerStatus ...................................... 49
5.2.3 Timer Active, -Start and -End Signal . . . . . . . . . . . . . . . . . . . . . . . . 50
5.2.4 TimerReset....................................... 50
5.2.5 TimerTriggerSource ................................. 50
6 Encoder 53
6.1 EncoderUsage......................................... 53
6.2 Encodertriggeroutput.................................... 54
6.3 EncoderStatus......................................... 54
6.4 EncoderResetSource..................................... 55
7 I/O Control 57
7.1 InputSignalPath ....................................... 57
7.2 OutputSignalPath ...................................... 58
8 Action Control 59
8.1 ActionCommandUsage ................................... 59
8.2 ActionControlOutput .................................... 60
9 Image Format Control 61
9.1 RegionofInterest(ROI) ................................... 61
9.2 Multiple Regions of Interest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
9.3 Pixelformat .......................................... 65
9.4 Decimation (monochrome cameras) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
10 High Dynamic Range Mode (HDR) 69
10.1 Multiple Slope Mode (High Dynamic Range) . . . . . . . . . . . . . . . . . . . . . . . 69
11 Frame Rate 71
11.1MaximumFrameRate .................................... 71
4 of 151 MAN085 04/2021 V1.3

CONTENTS
12 Pixel Data Processing 73
12.1Overview ............................................ 73
12.2BadPixelCorrection...................................... 74
12.2.1 Enable / Disable the Bad Pixel Correction . . . . . . . . . . . . . . . . . . . . . 74
12.2.2 Calibration of the Bad Pixel Correction . . . . . . . . . . . . . . . . . . . . . . 74
12.2.3 Storing the calibration in permanent memory . . . . . . . . . . . . . . . . . . 75
12.3ColumnFPNCorrection.................................... 75
12.3.1 Enable / Disable the Column FPN Correction . . . . . . . . . . . . . . . . . . . 75
12.3.2 Calibration of the Column FPN Correction . . . . . . . . . . . . . . . . . . . . . 75
12.3.3 Storing the calibration in permanent memory . . . . . . . . . . . . . . . . . . 76
12.4GainandOffset ........................................ 76
12.5 Grey Level Transformation (LUT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
12.5.1Gain........................................... 77
12.5.2Gamma......................................... 79
12.5.3 User-defined Look-up Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
12.5.4 Region LUT and LUT Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
12.6Binning ............................................. 83
12.6.1Description....................................... 83
12.6.2Camerasettings.................................... 83
12.7DualCrosshairs......................................... 85
12.8TestImages........................................... 87
12.8.1Ramp .......................................... 87
12.8.2LFSR........................................... 87
12.8.3 Troubleshooting using the LFSR . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
12.9 Status Line and Image Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
12.9.1ImageAverageValue................................. 89
12.9.2StatusLineFormat .................................. 89
12.9.3CameraTypeCodes.................................. 91
12.10Double Rate (DR cameras only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
12.11FrameCombine ........................................ 92
12.11.1FrameCombineTimeout............................... 92
13 Precautions 95
13.1IMPORTANTNOTICE! ..................................... 95
14 Hardware Interface 99
14.1AbsoluteMaximumRatings ................................. 99
14.2 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
14.3GigECameraConnector ...................................101
14.4 Power Supply / Power Over Ethernet (PoE) . . . . . . . . . . . . . . . . . . . . . . . . 103
14.5 Status Indicator (GigE cameras) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
14.6I/OConnector .........................................105
14.6.1Overview........................................105
14.6.2InputFaultDetection.................................107
14.6.3 Single-ended Line Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
14.6.4EncoderInterface...................................109
14.6.5 Single-ended Line Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
14.6.6 Master / Slave Camera Connection . . . . . . . . . . . . . . . . . . . . . . . . . 112
14.7I/OWiring ...........................................113
14.7.1SeparateGrounds...................................113
14.7.2 Common Grounds with Star Wiring . . . . . . . . . . . . . . . . . . . . . . . . 114
MAN085 04/2021 V1.3 5 of 151

CONTENTS
15 Mechanical Considerations 117
15.1MechanicalInterface .....................................117
15.1.1 MV4-D1280-L01 with GigE Interface . . . . . . . . . . . . . . . . . . . . . . . . 118
15.1.2 MV4-D1952-L01 with GigE Interface . . . . . . . . . . . . . . . . . . . . . . . . 120
15.1.3C-mountM42Adapter ................................123
15.2AdjustingtheBackFocus...................................124
15.3OpticalInterface........................................124
15.3.1CleaningtheSensor..................................124
16 Troubleshooting 127
16.1Noimagescanbeacquired .................................127
16.1.1 No acquisition due to no triggers . . . . . . . . . . . . . . . . . . . . . . . . . . 127
17 Standards Compliance 129
17.1 Directives and General Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
17.2 Country-specific Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
17.2.1 For customers in the USA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
17.2.2 For customers in Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
17.2.3 Pour utilisateurs au Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
17.3Lifesupportapplications...................................130
18 Warranty 131
18.1WarrantyTerms ........................................131
18.2WarrantyClaim ........................................131
18.3BreachofWarranty......................................131
19 Support and Repair 133
19.1TechnicalSupport .......................................133
19.2 Repair and obtaining an RMA Number . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
19.3 Temporal Abandoning and Scrapping . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
20 References 135
A Pinouts 137
A.1 I/OConnector .........................................137
A.2 GigEConnector ........................................139
B Camera Timing 141
B.1 Timed Exposure Mode Camera Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
C Use Cases 143
C.1 Acquisition...........................................143
C.1.1 Camera runs in "free-running" mode . . . . . . . . . . . . . . . . . . . . . . . 143
C.1.2 Camera runs in "constant frame rate" mode . . . . . . . . . . . . . . . . . . . 143
C.1.3 Camera runs in triggered mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
C.1.4 Camera runs in burst triggered mode . . . . . . . . . . . . . . . . . . . . . . . 144
C.1.5 Trigger controlled exposure mode . . . . . . . . . . . . . . . . . . . . . . . . . 145
C.2 Timer ..............................................145
C.2.1 StrobeSignalOutput.................................145
C.3 Counter.............................................146
C.3.1 CounterReset .....................................146
C.3.2 ImageCounter.....................................146
C.3.3 RealTimeCounter ..................................146
C.3.4 Missed Trigger Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
6 of 151 MAN085 04/2021 V1.3

CONTENTS
C.4 Look-UpTable(LUT) .....................................147
C.4.1 Overview........................................147
C.4.2 FullROILUT ......................................147
C.4.3 RegionLUT.......................................148
C.4.4 User defined LUT settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
C.4.5 Predefined LUT settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
C.5 Encoder.............................................148
C.5.1 Configuration of the encoder AB signals . . . . . . . . . . . . . . . . . . . . . 149
C.5.2 Configuration of the encoder Z signal . . . . . . . . . . . . . . . . . . . . . . . 149
C.5.3 Configuration of the encoder ALARM signal . . . . . . . . . . . . . . . . . . . 149
D Document Revision History 151
MAN085 04/2021 V1.3 7 of 151

CONTENTS
8 of 151 MAN085 04/2021 V1.3

1
Preface
1.1 IMPORTANT NOTICE!
READ THE INSTRUCTIONS FOR USE BEFORE
OPERATING THE CAMERA
STORE THE INSTRUCTIONS FOR USE FOR
FURTHER READING
Photonfocus AG
Bahnhofplatz 10
CH-8853 Lachen SZ
Switzerland
www.photonfocus.com
[email protected]
+41 – 55 451 00 00
MAN085 04/2021 V1.3 9 of 151

1 Preface
1.2 About Photonfocus
The Swiss company Photonfocus is one of the leading specialists in the development of CMOS
image sensors and corresponding industrial cameras for machine vision.
Photonfocus is dedicated to making the latest generation of CMOS technology commercially
available. Active Pixel Sensor (APS) and global shutter technologies enable high speed and
high dynamic range (120 dB) applications, while avoiding disadvantages like image lag,
blooming and smear.
Photonfocus’ product range is complemented by custom design solutions in the area of camera
electronics and CMOS image sensors.
Photonfocus is ISO 9001 certified. All products are produced with the latest techniques in order
to ensure the highest degree of quality.
1.3 Contact
Photonfocus AG, Bahnhofplatz 10, CH-8853 Lachen SZ, Switzerland
Sales Phone: [phone] Email: [email protected]
Support Phone: [phone] Email: [email protected]
Table 1.1: Photonfocus Contact
1.4 Sales Offices
Photonfocus products are available through an extensive international distribution network
and through our key account managers. Find your local Photonfocus contact at our homepage
(www.photonfocus.com) or contact us via email at [email protected].
1.5 Further information
Photonfocus reserves the right to make changes to its products and documenta-
tion without notice. Photonfocus products are neither intended nor certified for
use in life support systems or in other critical systems. The use of Photonfocus
products in such applications is prohibited.
Photonfocus and LinLog®are registered trademarks of Photonfocus AG.
CameraLink®and GigE Vision®are a registered mark of the Automated Imag-
ing Association (AIA). Product and company names mentioned herein are trade-
marks or trade names of their respective companies.
Reproduction of this manual in whole or in part, by any means, is prohibited
without prior permission having been obtained from Photonfocus AG.
10 of 151 MAN085 04/2021 V1.3

1.6 Legend
Photonfocus can not be held responsible for any technical or typographical er-
rors.
1.6 Legend
In this documentation the reader’s attention is drawn to the following icons:
Important note, additional information
Important instructions
General warning, possible component damage hazard
Warning, electric shock hazard
Warning, fire hazard
MAN085 04/2021 V1.3 11 of 151

1 Preface
12 of 151 MAN085 04/2021 V1.3

2
Introduction
2.1 Introduction
This manual describes standard Photonfocus MV4 Luxima series cameras that have a Gigabit
Ethernet (GigE) or a 10 Gigabit Ethernet Copper (GT) or Fibre (FB) interface. The cameras
contain the CMOS image sensor LUX1310 and LUX2100 from Luxima.
DR cameras use a proprietary coding algorithm to double the maximal frame rate compared
to a standard GigE camera over one GigE cable.
2.2 Camera Naming Convention
The naming convention of the MV4 Luxima camera series is summarized in Fig. 2.1.
MV 4 - D 1 2 8 0 C - L 0 1 - G 2
Pr e f i x 1
P r e f i x 2
S e n s o r w i d t h
( o p t i o n a l )
S e n s o r t y p e
I n t e r f a c e
t y p e
S e n s o r
M a n u f a c t u r e r
S e n s o r
F a m i l y
Figure 2.1: Camera naming convention
Prefix1 Camera platform and usage prefix. The following prefix are available for this camera
series: MV4 with form factor 59mmx59mm. DR cameras have DR4 as Prefix1.
Prefix2 Camera family specifier. The following specifiers are used in this manual: "D": digital
standard area scan cameras
Sensor width Width of image sensor of the camera in pixels.
Sensor type Sensor types specification: "C": color cameras. Cameras without sensor type
specifier have a standard monochrome sensor.
Sensor Manufacturer Sensor manufacturer. "L": Luxima
Sensor Family Sensor family of the prior indicated manufacturer. "01": LUX series
Interface type Interface type specification: "CL": CameraLink®, "G2": Gigabit Ethernet (GigE
Vision), "GT": 10 Gigabit Ethernet Copper (GigE Vision), "FB": 10 Gigabit Ethernet Fibre
(GigE Vision).
2.3 Camera list
A list of all cameras covered in this manual is shown in Table 2.1.
MAN085 04/2021 V1.3 13 of 151

2 Introduction
Name Resolution Frame Rate Notes
MV4-D1280-L01-G2 1280 x 1024 85 fps 1) Gigabit Ethernet 1.3 MP monochrome
standard camera.
MV4-D1280-L01-GT 1280 x 1024 935 fps 1) 10 Gigabit Ethernet Copper 1.3 MP
monochrome standard camera.
MV4-D1280-L01-FB 1280 x 1024 935 fps 1) 10 Gigabit Ethernet Fibre 1.3 MP
monochrome standard camera.
DR4-D1280-L01-G2 1280 x 1024 165 fps 1) Gigabit Ethernet 1.3 MP monochrome
standard camera.
DR4-D1280-L01-GT 2) 1280 x 1024 1066 fps 1) 10 Gigabit Ethernet Copper 1.3 MP
monochrome standard camera.
DR4-D1280-L01-FB 2) 1280 x 1024 1066 fps 1) 10 Gigabit Ethernet Fibre 1.3 MP
monochrome standard camera.
MV4-D1952-L01-G2 2) 1952 x 1080 53 fps 1) Gigabit Ethernet 2.1 MP monochrome
standard camera.
MV4-D1952-L01-GT 1952 x 1080 581 fps 1) 10 Gigabit Ethernet Copper 2.1 MP
monochrome standard camera.
MV4-D1952-L01-FB 2) 1952 x 1080 581 fps 1) 10 Gigabit Ethernet Fibre 2.1 MP
monochrome standard camera.
DR4-D1952-L01-G2 2) 1952 x 1080 TBD fps 1) Gigabit Ethernet 2.1 MP monochrome
standard camera.
DR4-D1952-L01-GT 1952 x 1080 1000 fps 1) 10 Gigabit Ethernet Copper 2.1 MP
monochrome standard camera.
DR4-D1952-L01-FB 2) 1952 x 1080 1000 fps 1) 10 Gigabit Ethernet Fibre 2.1 MP
monochrome standard camera.
Table 2.1: Camera models covered by this manual (Footnotes: 1)frame rate at at full resolution2)available
on request)
14 of 151 MAN085 04/2021 V1.3

3
Product Specification
3.1 Introduction
The Photonfocus MV4 Luxima GigE camera series is built around the CMOS image sensor
LUX1310 and LUX2100 from Luxima. They provide a resolution of 1280 x 1024 and 1592 x 1080
pixels. The camera series is optimized for low light conditions. The cameras are aimed at
standard applications in industrial image processing where high sensitivity and high frame
rates are required.
The principal advantages are:
• Resolution of 1280x1024 (LUX1310) and 1952 x 1080 (LUX2100) pixels
• Optimized for low light conditions
• Spectral range: monochrome standard: 350 - 950 nm
• Global shutter high-speed CMOS image sensor
• Micro lenses
• Gigabit and 10-Gigabit Ethernet interfaces, GigE Vision and GenICam compliant
• Powered by Wall Adapter or Power Over Ethernet (PoE).
• Reverse voltage protection
• Frame rates MV4-D1280-L01 camera series at maximal resolution 85 fps (GigE) and 935 fps
(10GigE)
• Frame rates MV4-D19520-L01 camera series at maximal resolution 53 fps (GigE) and 581
fps (10GigE)
• I/O capabilities: 4x Isolated inputs or shaft encoder A, B, Z, Y interface (RS422, TTL, D-HTL,
HTL), 3x Isolated outputs (2x open drain, 1x TTL highspeed)
• Up to 8 regions of interest (MROI)
• 2 look-up tables (12-to-8 bit) on user-defined image region (Region-LUT)
• Dual Crosshairs overlay on the image
• Image Binning
• Image information and camera settings inside the image (status line)
• Software provided for setting and storage of camera parameters
• The rugged housing at a compact size of 59 x 59 x 89.6 mm3(GigE), 59 x 59 x 103.2 mm3
(10GigE) and 59 x 59 x 101.8 mm3(10GigE Fibre) makes the Photonfocus MV4 Luxima GigE
camera series the perfect solution for applications in which space is at a premium.
• Lens mount: C-Mount (LUX1310); M42 (LUX2100); C-mount adapter available
• Mechanically adjustable back focus ring
• Exchangeable optical filters available on request
• The DR models use a proprietary coding algorithm to double the maximal frame rate
compared to a standard GigE camera over one GigE cable.
The general specification and features of the camera are listed in the following sections.
MAN085 04/2021 V1.3 15 of 151

3 Product Specification
Figure 3.1: Photonfocus MV4 Luxima GigE camera series
Figure 3.2: Photonfocus MV4 Luxima 10 GigE camera series
Figure 3.3: Photonfocus MV4 Luxima 10 GigE fibre camera series
16 of 151 MAN085 04/2021 V1.3

3.1 Introduction
Figure 3.4: Photonfocus MV4 Luxima 10 GigE ruggedized fibre camera series
MAN085 04/2021 V1.3 17 of 151

3 Product Specification
3.2 Feature Overview
The general specification and features of the camera are listed in the following sections. The
detailed description of the camera features is given in the following chapters.
Characteristics Photonfocus MV4 Luxima GigE Camera Series
Interface Gigabit and 10-Gigabit Ethernet (Copper & Fibre), GigE Vision and
GenICam compliant
Camera Control GigE Vision Suite
Trigger Modes Software Trigger / External isolated trigger inputs / A/B Trigger
Features
• Greyscale / colour resolution 12 bit / 10 bit / 8 bit
• Region of Interest (ROI)
• Up to 8 regions of interest (MROI)
• 2 look-up tables (12-to-8 bit) on user-defined image region
(Region-LUT)
• Test pattern (LFSR and grey level ramp)
• Image information and camera settings inside the image (status line)
• Dual Crosshairs overlay on the image
• Image Binning
• 4 isolated trigger inputs and 3 isolated outputs
Table 3.1: Feature overview
.
18 of 151 MAN085 04/2021 V1.3

3.3 Technical Specification
3.3 Technical Specification
1.3 MPix Cameras 2.1 MPix Cameras
Sensor Manufacturer Luxima
Sensor Type LUX1310 LUX2100
Technology CMOS active pixel
Scanning system progressive scan
Optical format / diagonal 2/3” / 10.82 mm 4/3" / 22.31 mm
Resolution 1280 x 1024 pixels 1952 x 1080 pixels
Pixel size 6.6 µm x 6.6 µm 10 µm x 10 µm
Active optical area 8.45 mm x 6.76 mm 19.52 mm x 10.8 mm
Full well capacity 15 ke−21 ke−
Spectral range standard sensor <350 to 950 nm 2)
Responsivity (@ 560nm / 8bit) 994 x 103DN / (J/m2) 1600 x 103DN / (J/m2)
Quantum Efficiency > 54 % @ 550nm > 50 % @ 550nm
Optical fill factor > 45 % 3) >35 % 3)
Dark current 41100 e−/s @ 25°C 17800 e−/s @ 45°C
Dynamic range 57 dB 54 dB
Micro lenses Yes
Characteristic curve Linear, Piecewise linear (multiple slope)
Shutter mode global shutter
Sensor bit depth 12 bit
Maximal frame rate MV4 GigE 1) 85 fps 53 fps
Maximal frame rate MV4 10GigE 1) 935 fps 581 fps
Maximal frame rate MV4 10GigE Fibre 1) 935 fps 581 fps
Maximal frame rate DR4 GigE models 1) 165 fps TBD fps
Maximal frame rate DR4 10GigE 1) 1066 fps 1000 fps
Maximal frame rate DR4 10GigE Fibre 1) 1066 fps 1000 fps
Camera pixel formats MV4 12 / 10 / 8 bit
Camera pixel formats DR4 8 bit
Digital gain 0.1 to 15.99 (Fine Gain)
Exposure time range 10 µs ... 186 ms 10 µs ... 223 ms
Table 3.2: General specification of the Photonfocus MV4 Luxima GigE camera series (Footnotes: 1)at full
resolution; 2)to 10% of peak responsivity; 3)without micro lenses; 2)In trigger controlled exposure, the
trigger pulse is extended by the camera by 3 µs (LUX1310) resp. 2.667 µs (LUX2100), meaning the minimum
pulse width is 7 µs resp. 7.333 µs)
MAN085 04/2021 V1.3 19 of 151

3 Product Specification
MV4-D1280-L01 GigE Camera Series
Operating temperature / moisture 0°C ... 50°C / 20 ... 80 % (GigE)
0°C ... 40°C / 20 ... 80 % (10GigE)
0°C ... 45°C / 20 ... 80 % (10GigE Fibre)
Storage temperature / moisture -25°C ... 60°C / 20 ... 95 %
Camera Power Supply +12 V DC (- 10 %) ... +24 V DC (+ 10 %)
PoE Conformity IEEE 802.3bt standard Class 4
Trigger signal input range +5 V .. +30 V DC
Maximal power consumption < 8.6 W (GigE)
< 15.8 W (10GigE)
< 11.9 W (10GigE Fibre)
Lens mount C-Mount
I/O Inputs 4x Isolated inputs or shaft encoder A, B, Z, Y interface
(RS422, TTL, D-HTL, HTL)
I/O Outputs 3x Isolated (2x open drain, 1x TTL highspeed)
I/O Control 1x Isolated RS485
Dimensions 59 x 59 x 89.6 mm3(GigE)
59 x 59 x 103.2 mm3(10GigE)
59 x 59 x 101.8 mm3(10GigE Fibre)
Mass 392 g (GigE)
465 g (10GigE)
495 g (10GigE Fibre)
Connector I/O 17-pin M12
Connector Interface Copper X-coded M12
Connector Interface Fibre LC connector for multimode fibre (through included
SFP+ cage)
Conformity CE / RoHS / WEEE
IP Code IP40
Table 3.3: Physical characteristics and operating ranges MV4-D1280-L01 GigE Camera Series
.
20 of 151 MAN085 04/2021 V1.3